HIR Workshop

Objective

The objective of this workshop is to analyze and complete an incomplete house plan with an electrical plan, a plumbing plan, an extra story (floor), a roof, and additional utilities using Autodesk Revit.

Overview

Revit

Autodesk Revit is a Building Information Modeling (BIM) software used by architects, engineers, and contractors to plan, design, construct, and manage building and infrastructure designs. For architects, Revit is used to create floor plans, elevations, and 3D views in addition to rendering and animating the building design. For structural engineers, Revit is used to analyze and evaluate how well a building conforms to building and safety regulations. For mechanical, electrical, and plumbing (MEP) engineers, Revit allows coordination with architects and other engineers to design systems with all the architectural and structural components. For construction professionals, Revit is used to plan and understand construction methods, materials, and schedules.

Plumbing & Electrical Plans

In addition to other technical drawings, architects, engineers, and contractors require plumbing and electrical plans to accurately construct buildings. Plumbing plans show various plumbing fixtures, such as sinks, toilets, and showers, and the pipes connecting these fixtures to water sources and disposal systems. There are three main types of water systems: hot water, cold water, and sanitary water. Hot and cold water systems introduce filtered, ready-to-use water into the plumbing system while sanitary systems remove wastewater from the system and route this water to treatment facilities. Plumbing plans ensure that each component receives the right type of water and has adequate disposal of wastewater.

Electrical plans show the electrical components within a building. These schematics include the electrical circuits within the system. Each electrical circuit is routed to a centralized panel board that houses circuit breakers and fuses, one for each electrical circuit. Electrical plans also show electrical outlets that have two main types: default and ground fault circuit interrupters (GFCI). GFCI outlets are mainly used near water sources as they help prevent water damage to circuits that can cause fatal accidents where current can be inadvertently directed away from the outlet and cause shock. Electrical plans direct the wiring of outlets and other appliances.

LEED Accreditation

Leadership in Energy and Environmental Design (LEED) is an internationally used green building certification program developed by the U.S. Green Building Council. To receive LEED certification, building projects must satisfy prerequisites and earn points to achieve different levels of certification. The different categories for the LEED checklist correspond to principles of design, construction, and maintenance. The eight LEED categories with brief descriptions are:

1. Location and Transportation
   1. Diverse land use
   2. Disability access
   3. Bicycle and EV facilities
   4. Reduced parking footprint
2. Sustainable Sites
   1. Open space
   2. Rainwater management
   3. Heat island reduction
   4. Light pollution reduction
3. Water Efficiency
   1. Water quality management
   2. Water use reduction
   3. Water heating and cooling
   4. Advanced water metering
4. Energy and Atmosphere
   1. Optimize energy performance
   2. Advanced energy metering
   3. Demand response
   4. Renewable energy production
5. Materials and Resources
   1. Waste reduction
   2. Avoid mercury containing materials and devices
   3. Using reusable materials for which life-cycle information is known
6. Indoor Environmental Quality
   1. Air quality management
   2. Interior lighting/daylight
   3. Thermal comfort
   4. Acoustic performance
7. Innovation
   1. Connected building
   2. Intelligent inventory
   3. Security and safety
   4. Sustainability not covered in other topics
8. Regional Priority
   1. Addressing region-specific environmental, social equity, and public health priorities

Third-Party Revit Components

While Revit has a wide range of components, additional components can be downloaded from third-party websites and imported into existing Revit files. Common third-party websites include BIMObject, BIMSmith, and RevitCity. These websites are continuously updated with new components. Making an account with one of these sites will be extremely beneficial in the completion of both your project and this workshop.

Materials and Equipment

• Autodesk Revit 2023 or newer

Procedure

In this workshop, an electrical plan, a plumbing plan, designing and connecting multiple floors, and designing a roof will be completed. An incomplete two-floor house plan is provided to explore these skills. Download the incomplete two-floor house plan RVT file here. To avoid compatibility issues, use Autodesk Revit 2023 or a newer version. The file that is attached above is a .zip file. To extract the files you must download it, click on the folder once, then at the top ribbon click “Extract”. From there you will be able to open the relevant files to complete this workshop.

Plumbing Plan

In this part, a plumbing plan will be created for one bathroom on the first floor. Understanding the implementation of a plumbing plan will be important for the completion of Benchmark B for the Housing in Revit (HIR) semester-long design project (SLDP).

1. Open the file above.
2. Select File Icon then NEW and select Browse in the pop up menu. Open the template file named Plumbing-Default.rte and select OK (Figure 1).

   

   Figure 1: Plumbing Default Template

3. Save the plumbing plan file under an appropriate name.
4. Insert the architectural model by going to the Insert tab and selecting Link Revit. Find the file name of the architectural template and select Open (Figure 2).

   

   Figure 2: Linking Architectural Design

5. Hover the mouse over the design and left-click once a blue box surrounds the design. This will highlight every element in the design (Figure 3).

   

   Figure 3: Highlighted Elements

6. Select the pin icon under the Modify tab (Figure 4). This prevents the linked file from being moved.

   

   Figure 4: Pin Icon

7. Select Edit Type in the Properties sidebar. Check the box corresponding to Room Bounding and select OK (Figure 5).

   

   Figure 5: Room Bounding

8. Go to the View tab, select Callout. Click and drag over a large area of space containing the plumbing fixtures on the first floor (Figure 6).

   

   Figure 6: Callout of the Bathroom

9. Select the Callout plan under the Floor Plans section of the Project Browser (Figure 7).

   

   Figure 7: Viewing the Callout

10. Select Plumbing Fixtures under the Systems tab. Under the Mode tab, select Load Family. Browse through the library of items until the plumbing fixtures used in the incomplete architectural plan are selected. For the bathroom on the first floor on the template, the File Path of the toilet, the sink, and the shower used are shown in Table 1.

Table 1: File Paths for Required Plumbing Components

Components	File Paths
Sink	English Imperial → Plumbing → MEP → Fixtures → Sinks → Sink - Work
Toilet	English Imperial → Plumbing → MEP → Fixtures → Water Closets → Water Closet - Flush Tank
Shower	English Imperial → Plumbing → MEP → Fixtures → Shower → Shower Stall - Rectangular

11. Align the new plumbing fixtures to the original plumbing fixtures from the incomplete architectural plan. Use the spacebar to rotate the fixtures if necessary.
1. Note that in the architectural plan, the sink is 3 ft off the ground. In the plumbing plan, make sure that the sink is also 3 ft off the ground in the Properties sidebar (Figure 8).

   

   Figure 8: Properties Sidebar

12. Three piping systems can be created: a hot water system, a cold water system, and a sanitary system. In this workshop, only the cold water system will be used. To add pipes, click on a fixture and select the Create Pipe icon (Figure 9). Choose the cold water icon and not the sanitary icon.

1. 

   Figure 9: Create Pipe Icon

13. The pipes can be routed in any direction by left-clicking and creating joints. Click and drag the cold water pipe around the bathroom (Figure 10).

1. 

   Figure 10: Cold Water Pipe

14. Multiple fixtures can be added to the same pipeline. Select the fixture and select Connect Into under the Modify tab. Click Connector 1: Domestic Cold Water and select OK. Select the cold water pipe created in Step 12. Complete this step for the shower and the sink. The final plumbing plan for the cold water system is shown in Figure 11. For the Housing in Revit SLDP, the hot water system and the sanitary system must be completed. For this workshop, move on to the electrical plan.

1. 

   Figure 11: Completed Cold Water System

Electrical Plan

In this part, an electrical plan will be created for the first floor of the home. Understanding the implementation of an electrical plan will be important for the completion of Benchmark B for the Housing in Revit (HIR) SLDP.

1. Open Autodesk Revit.
2. Select Models then NEW and select Browse in the pop up menu. Open the template file named Electrical-Default.rte and select OK (Figure 12).

   

   Figure 12: Electrical Default Template

3. Save the electrical plan under an appropriate name.
4. Insert the architectural model by going to the Insert tab and selecting Link Revit. Find the file name of the architectural template and select Open.
5. Hover the mouse over the design and left-click once a blue box surrounds the design. This will highlight every element in the design.
6. Select the pin icon under the Modify tab. This prevents the linked file from being moved.
7. Add a panelboard by accessing the Level 1 Floor Plan of the original file by clicking on the 1 - Power option under the Power listing of the Project Browser (Figure 13).

   

   Figure 13: Level One Floor Power Plan

8. Select Electrical Equipment under the Systems tab. A panel board will be added through the Load Family option. The File Path to the panel board is shown in Table 2.
9. Place the selected panel board on a wall. Sometimes Autodesk Revit will not recognize it as a panel board. If this occurs, insert the panel board using the Add Component tool.

Table 2: File Path for the Panel board

Components	File Paths
Panelboard	Electrical → MEP → Electric Power → Distribution → Lighting and Appliance Panel board - 208V MCB - Surface

10. Press the Esc key to deselect the panel board. Select the panel board again and it should highlight in blue. Select the dropdown arrow near the Create Panel Schedule option under the Modify tab in the project ribbon. Select Use Default Template (Figure 14).

1. 

   Figure 14: Creating Panel Schedule

11. A branch panel schedule will appear. Click on the area to the right of Branch Panel and rename the schedule (Figure 15). Usually the schedule is named after the floor the panel is located on.

1. 

   Figure 15: Renaming the Schedule

12. Return to the electrical plan of the first floor. Under the Systems tab, under Electrical, select the Device option. In the dropdown menu, select the Electrical Fixture option. Select Duplex Receptacle under the Properties window and place the outlets along the interiors of the walls (Figure 16). Use the standard model unless the outlets are placed near a water source, such as a sink. In that case, use the GCFI model.

1. 

   Figure 16: Placing Outlets

13. Add switches. Select the Lighting option on the dropdown menu in the Device option on the Systems tab. In the Properties window, select Lighting Switches Circuit Breaker. Place them next to the door so that they are within arm’s reach once the door is opened (if possible, not on the hinge side).
14. Add ceiling lights. Open the ceiling plan of the first floor by selecting 1 - Ceiling Elec under the Project Browser (Figure 17).

1. 

   Figure 17: Ceiling Plan

15. Select Lighting Fixture under the Systems tab and Electrical subtab. Load the desired lights in through the Load Family option. The file path of the ceiling lights is shown in Table 3. Select Place on Face under the Modify tab and attach the lights to the corresponding area from the architectural plan.

Table 3: File Path for the Ceiling Lights

Components	File Paths
Ceiling Light	Lighting → MEP → Internal → Ceiling Light - Flat Round

16. Create a circuit for the lights and a circuit for the power outlets. To generate the circuit for the lights, select any switch and select Power under the Modify tab (Figure 18). In the Specify Circuit Information window that appears, select 120 V.

1. 

   Figure 18: Creating Electrical Circuit

17. Click on the Panel dropdown menu and select the panel board for the first floor (Figure 19).

1. 

   Figure 19: Panel Designation

18. Select Edit Circuit under the Modify tab. Select the ceiling lights that are connected to the circuit. Select the green check mark to complete the circuit. Repeat this step for all the switches and their corresponding lights.
19. Hover over any components of the electrical circuit and click Tab on the keyboard. A dashed representation of the circuit will temporarily be displayed. Click on the component that was hovered over to create a permanent display (Figure 20).

1. 

   Figure 20: Circuit Display

20. Under the Modify tab, select either Arc Wire or Chamfered Wire. Solid wires will appear to connect all the circuit components and the panel board (Figure 21).

1. 

   Figure 21: Adding Wires to the Circuit

21. Go back to the Panel Schedule view under the Project Browser. A new circuit should appear. Rename the Circuit Description with an appropriate title, such as organization by the type of room.
22. Repeat steps 14-19 for the outlets instead of the lights and switches. Each outlet should be connected to the panel board.
23. The electrical plan is now completed. Only the electrical plan for the first floor will be made for this workshop. Move on to the creation and connection of multiple floors.

Complete the Architectural Plan

In this part, a third floor will be added to the architectural plan. All three floors will then be connected by stairs. A roof will be added to finish the design of the house.

1. Open the incomplete architectural template on Autodesk Revit.
2. Add a third floor. To add multiple floors, use the same procedure. Select one of the Elevations views under the Project Browser window (Figure 22).

   

   Figure 22: Elevations View

3. Select the Datum Level tool in the project ribbon. (Figure 23).

   

   Figure 23: Datum Level Tool

4. Left-click and draw a line in the project space 10 feet above the previous floor to create the elevation. The project browser should be updated with the new elevation views (Figure 24).

   

   Figure 24: Creating New Elevation

5. To extend the walls to the new floor, select the Level 1 Floor Plan in the Project Browser window. Highlight all the walls by holding down Ctrl and left clicking the walls. In the Properties window, change the Top Offset to the height of the top floor. In this workshop, the offset should be 20 ft (Figure 25).
   1. To verify any component in the 3D View, hide elements, such as walls, ceilings, and floors, by right-clicking on the elements and selecting Hide in View. They can be unhidden by selecting the lightbulb icon in the bottom to reveal hidden elements. Red outlines of the hidden elements will be displayed. Selecting Unhide in View once selected will unhide the elements.

   

   Figure 25: Changing Top Offset of the Walls

6. Create a ceiling for the second floor. Select the Level 2 Ceiling Plan under the Project Browser window. Select the Ceiling tool in the Architecture tab. Select the Automatic Ceiling option under the Modify tab. Select the area within the floor to create the ceiling (Figure 26).

   

   Figure 26: Automatic Ceiling

7. Create a floor for the third floor. Select the Level 3 Floor Plan under the Project Browser window. Then select Floor: Architectural in the Architecture tab, and use the line tools in the Draw tab to outline the inner edge of the outer walls (Figure 27). Then select the green check mark.

   

   Figure 27: Adding the Floor

8. Repeat step 6 for the ceiling on the third floor.
9. Add a shaft and stairs to connect the three floors. Select the Level 1 Floor Plan in the Project Browser window. Select the Shaft option in the Architecture tab (Figure 28).

   

   Figure 28: Shaft Option

10. Draw the area of the shaft in an open area. Make the shaft larger than necessary. The size of the shaft can be adjusted after the staircase is placed. The shaft should be placed carefully since it can run through different elements of other floors.
11. Select the Stair option under the Architecture tab. Click and drag the stairs along the shaft to create the stairs. If an error message appears, that means that the stairs are not long enough to extend to the next floor. Extend the stairs and adjust the shaft so that they fit (Figure 29). Alternatively, the Desired Number of Risers under the Properties window and the Actual Run Width under the Project ribbon can be used to adjust the staircase to fit the shaft.
    1. For multiple levels, select Connect Levels under the Modify tab when editing the stairs. In the window that appears, select the levels that the stairs should connect to. Click the green check mark to finish editing.

    

    Figure 29: Creating Stairs

12. Select the shaft. In the Properties window, change the base offset of the shaft to 0 ft so that there is not a hole in the floor. The stairs are now completed.
13. Create a roof. Follow steps 3 - 4 to create a Level 4. Select the Level 3 Floor Plan in the Project Browser window. Select the Roof option in the Architecture tab. In the Properties window, change the Base Level to Level 4. Select the outer layers of the walls, then select the green check mark to complete the roof (Figure 30).

    

    Figure 30: Completed Roof

Designing the Third Floor

Only complete this part of the workshop if there is extra time in the workshop session. Otherwise, begin working on the Housing in Revit SLDP.

Design the interior floor plan of the third floor of the building. Make sure to have at least one bathroom and one bedroom. Windows and lights should be added as needed. Try to use one imported component from a third-party website. To import a component, follow the procedure.

1. Go to revitcity.com or market.bimsmith.com
2. Create an account.
3. Search for the desired components.
4. Download the component.
5. Place the downloaded component into Autodesk Revit through the Load Family option under the Insert tab.

Assignment

Individual Lab Report

There is no lab report for Lab 4.

Team PowerPoint Presentation

There is no team presentation for Lab 4.

References

Autodesk. “Autodesk Revit Overview.” Autodesk, 2022. Retrieved 6 January 2022. http://www.imaginit.com/portals/4/documents/autodesk-revit2018-brochure_evergreen_v3.pdf

U.S. Green Building Council. “LEED v4 for Building Design and Construction.” USGBC, 2019. Retrieved 8 August 2021. https://www.usgbc.org/sites/default/files/LEED%20v4%20BDC_07.25.19_current.pdf.

Appendix

Multi-Floor Plumbing

1. To connect multi-level plumbing plans, edit the middle elevation to match the elevation of the pipe on the higher level.
2. Modify the pipes in any higher levels so that there is a pipe running along the floor of that level by changing the middle elevation to 0 ft.
3. Starting on the lower floor, change the Sloped Piping option to “Slope Up”. Change the middle elevation to the desired elevation. To connect pipes of consecutive floors, change the middle elevation to 10 ft.
4. Check if the piping connection was successful by going to the 3D View. A circle icon will display between the pipes if the connection was successful.

Walkthrough Video

A walkthrough is a method of rendering a Revit model to provide an interactive look at the project. Use the following steps to create a walkthrough video.

1. Define the camera path for the walkthrough.
   1. To do this, select the 3D View in the access toolbar. Click the 3D view drop-down menu -> Walkthrough (Figure 17). Click points in the view to establish the path that the camera will follow. Change the offset in the Options bar to adjust the height of the camera.
      

      Figure 17: Walkthrough in View Tab
   2. After defining the path, click Finish Walkthrough. A walkthrough branch will be added to the Project Browser now (Figure 18). Review the walkthrough video.
      

      Figure 18: Walkthrough in Project Browser
2. Edit the walkthrough video.
   1. When previewing the walkthrough video, the view is static and displays one frame only. To adjust what is visible in the camera, open an Elevations view (North/South/East/West) in the Project Browser. Then select the Tiles tool to tile these views with the walkthrough video.
   2. Select the crop region of the walkthrough and click Edit Walkthrough. Set the frame control on the Option bar to 1 to bring the camera back to the beginning position of the walkthrough. Activate the Site Plan view and set the Controls to Active Camera on the Options bar. Use the grip controls on the camera to adjust the target position and the view depth of the walkthrough camera. The walkthrough video will be updated as the camera is adjusted
   3. Click the Edit Walkthrough tab and use the playback controls to check and review the walkthrough video as it is made.