Product Evaluation (Sensors)
3D Modeling and CAD Video
General Engineering has created a video that covers the fundamental concepts of 3D modeling for the semester-long design project: 3D Modeling and CAD Video. This video provides the fundamental principles behind the engineering design process and will help determine what solutions justify creating a 3D model. Material covered in the video will be on the lab 3 quiz. Viewing the video is a mandatory pre-lab assignment.
A specified robot to evaluate has already been created for this lab using an EV3 robotics kit. The design will be evaluated for accuracy and precision by utilizing different designs and codes, the first two without the use of sensors and the third with. The robot will be tested on one of the two provided mini-courses. The data from the product evaluation of all sets of code will be used to determine if the robot should or shouldn’t use sensors.
Product evaluation is a common task for an engineer and for companies. Sometimes the product evaluated will be a company's product, and sometimes companies will be evaluating a competitor's design. In either case, this evaluation will use a standard (an accepted value), determine an average, and calculate accuracy and precision.
Professional engineers must be sure of standards. For the purpose of this lab, the EG1003 Standard will be 80% accuracy and the pre-set standards for tolerance. This means that the product has to achieve a percent accuracy of 80 percent and meet a tolerance of 1cm for distance and 10 degrees for angle.
When taking measurements, the first step is to determine an average.
In this equation, Ap is the average, P1, P2, P3, ..., Pn are the results of the tests and N is the total number of tests performed.
The average is compared to the standard. Accuracy is a variable the must always be considered. The degree of accuracy required will allow the results to be verified. Engineers often work on projects that affect people's safety; it is critical that the solutions to the problems solved by technical professionals are accurate.
The comparison of the average to the standard is called accuracy, defined as Acc in the following equation:
In this equation, Ps is the standard value, and Ap is the value measured. Accuracy is always a positive number, so use the absolute value in case Ps is less than Ap.
Precision is the repeatability of a result, or how close the results are to each other, defined as Prec in the following equation:
In this equation, Prec is precision, Phigh is the highest data value and Plow is the lowest data value. Like accuracy, precision is always a positive number, so use an absolute value here as well.
A product test can be accurate but imprecise, or precise but inaccurate (Figure 1). The goal is always the combination of accuracy and precision. In order for engineers to make a recommendation based on experimental test data, it is important to determine how a product compares to a standard. Engineers need these benchmarks to determine the quality of a product.
By determining the percent accuracy of an experiment, and comparing this percentage to a standard, it can be determined, based on experimental evidence, if the product has passed or failed. The equation for percent accuracy is:
In this equation, %Acc is the percent accuracy, Ps is the standard value, and Ap is the value measured.
Precision shows how precise a product is compared to the standard.
Adequate precision is determined by an acceptable tolerance, set by the manufacturer. In this lab, the precision of the robot must be compared to the tolerance allowed:
- Distance Test:
- Angle of Deviation Test:
Calculating percent accuracy and precision and then comparing those results to a standard determines the quality of the product.
Quality improvement is a process of analyzing a design and testing it either through physical modeling, computer simulation, or mathematical modeling. Quality improvement ensures that a product will perform as expected and allows improvements to be made to the design.
When deciding how to improve the design in this lab, keep these questions in mind:
- Does the robot perform to standard?
- If no, what can be done to improve its functionality?
- If yes, what can be done to improve its performance beyond the standard?
Changes will be implemented after testing the initial code.
Reverse engineering software involves reversing a program's machine code to obtain the original source code or determine the file structures the program uses. This needs to be done when source code is lost or is not available. For example, when a project is reactivated after being dormant for years to add new features to a product, the original design documentation may have disappeared. Also, when companies are writing a program that must interface to a second company's software, the second company may not have any incentive to cooperate by describing how the data in the files they use are organized, forcing the first company to deduce it on their own. Sometimes, this process is also undertaken as a way to improve the performance of a program, to fix a bug, or to find a virus. When the source code is obtained in this way for any of these reasons it is legal and necessary. Reverse engineering software in order to copy it constitutes a copyright violation and is illegal.
Hardware reverse engineering involves taking apart a device to see how it works. If a processor manufacturer wants to see how a competitor's processor works, the company can purchase the processor, disassemble it, and then make a new processor similar to it. In some countries, this process is illegal. Hardware reverse engineering is quite expensive and requires an expert in the field.
Carefully consider the desired results and what needs to be done to achieve it:
- What made or will make the results inconsistent?
- If the robot failed a test, why did it fail?
A sensor is something that measures some specific value and is used as an input. Different features can be measured by the EV3 sensors, such as light intensity, angle, or distance. The three sensors used in this lab are the light sensor, gyro sensor, and ultrasonic sensor.
The light sensor (or “color sensor”) can measure reflected light intensity, color, and ambient light, and is useful for when the robot has the option to follow a line or use differences in color to perform different actions (such as stopping when reaching a different color). If measuring color, the sensor outputs a value (0-7) that corresponds to a specific color. Measuring reflected light outputs a value (0-100) depending on the intensity of the light that is reflected. The ambient light works the same way as the reflected light, except it just measures the surrounding light. The light sensor, as well as all other sensors, can be found in the yellow category of MINDSTORMS:
The type of value the sensor can measure can be changed by clicking the small box on the bottom left of the block:
The gyro sensor can measure the exact degree it turns or the rate at which it is turning. For example, if the robot is set to turn 90 degrees using the gyro, the robot will keep trying to turn until 90 degrees is reached, regardless of any bumps in its way:
The ultrasonic sensor measures the distance between the robot and the closest object to it. It can measure distance in both centimeters and inches; the recommended range is 1 cm to 250 cm:
Switches and Loops
Switches and loops are used to tell the robot what actions to perform depending on the inputs taken from its surroundings, measured by the sensors.
A switch serves as an “if-else” statement: if the initial condition is true, the top action will occur, if false, the bottom action will occur. This block is used when the robot has to perform different actions depending on the situation it is in:
A switch will only run the code once, so if repeated action is desired, a loop must be used to repeat the switch’s statement. A loop continuously runs the code inside of it until the end statement occurs. The end statement can be determined with a sensor, or hard-coded to a specific amount of time or rotations; the figure below shows an infinite loop:
Materials and Equipment
- Mindstorms kit with pre-made robot
- Computer with Mindstorms software
- Mini-course with accuracy markings
Evaluate a pre-built robot by comparing its original design with a modified design, and then further comparing the sensor-less design with sensors. For each trial, record distance from the wall and angle of deviation. Test the first code by running four trials of Section 1 of the mini-course as marked on the physical course. Modify the robot design and create a second code without using any sensors, and run four trials of Section 1 again. Then create a line of code using switches and loops to incorporate the types of sensors found on the robot and features on the mini-course. Test again with four trials of Section 1. The total amount of trials for the whole procedure is 12. Download the pre-made Datasheet and fill in the data for each trial.
The mini-course is divided into two sections: one flat straight section of four tiles and a second section consisting of a right turn and ramp. Both sections have a wall at the end. In the following schematic, Section 1 is marked in red and Section 2 is marked in blue:
Part 1: Hardcoding
Conduct four trials of the original robot using a code without sensors to travel in a straight line across the first four tiles, stopping 5 cm from the wall.
- Start the Mindstorms EV3 software
- Click on the + in the top left corner to open up a blank program.
- The screen should look like this. Your program begins with the Start block.
- Place a Steering block from the Action palette next to the Start block. Set the Port to reflect both motors plugged into the brick; both ports have to be correct.
- Along the bottom of the Steering block, there are four options. On the left, there is a Mode Selector button, followed by three values for the input parameters picture above the value: from left to right, Power, Rotations, and Brake at End.
- Change the type of the Steering block to On for Seconds. This will change the Rotations input parameter to Seconds.
- Test different values of Power and Seconds to find the best settings to travel the first four tiles of the course and stop 5 cm from the wall. When the optimal settings are found, alert the TA and run the program. Run the program for a total of 4 trials. For each trial, record the distance between the robot and wall when the robot stops and the angle of deviation from the center line (draw in pencil a line from the tape to a point on the robot that started on the tape at the start of the trial and measure the angle with a protractor). Record the angle as though the straight line is 360 degrees.
Once completing four trials with the original robot, modify the robot to better suit the needs of the problem statement and increase overall accuracy and precision.
- Take apart parts of robot, if necessary.
- Analyze sub-assemblies and sketch a new robot design. Have the TA initial your sketch.
- Repeat the same testing procedure as above by taking distance from the finishing wall and angle of deviation for the four trials.
Part 2: Sensors
Using the modified robot created in the second part of Part 1, incorporate the use of sensors in the robot's code. The following steps outline how to build a line-following code for the robot to stay on track.
- Click on the + in the top left corner to open up a blank program.
- Insert a blank Loop. Insert a Switch within the loop.
- Set the input of the switch to a Light Sensor and the type to Reflected Light Intensity. Set the comparison to the “greater than” symbol and use Port View on the EV3 brick to measure the light intensity of the line. Set the value of the light intensity to the value displayed by Port View.
- In the top half of the switch, insert two Move Motor blocks. Set one to stop and one to continuously moving. Duplicate this in the bottom half but switch the ports. This way one wheel will move while the other stays stationary, which will make the robot wiggle along the line:
- Use the Ultrasonic Sensor to make the robot stop 5 cm away from the first wall. Set the end statement of the loop to be controlled by the ultrasonic sensor and set the type to Distance Centimeters for 5cm.
Tabulation of Results
All raw data must be inputted into the Datasheet. From the datasheet, determine if the EG standards were met for accuracy and precision; recorded precision must be divided by 2 to get the corresponding tolerance:
|Angle of Deviation Test|
|Modified Design w/out Sensors||Accuracy||%Acc||Pass/Fail||Precision||Tolerance||Pass/Fail|
|Angle of Deviation Test|
|Modified Design w/ Sensors||Accuracy||%Acc||Pass/Fail||Precision||Tolerance||Pass/Fail|
|Angle of Deviation Test|
Part 3: Robot Competition
The robot competition consists of a single timed trial of the second section of the course
The robot competition only requires the robot to travel the second (blue) section of the course. The second section requires turning to the right 90 degrees, advancing forward one tile, and turning another 90 degrees to prepare for going up the ramp. The robot must start facing the wall and 5 cm away, as though it had just completed the fist section.
- Each time the Gyro Sensor is used, it has to be reset in order to set the direction the robot is facing before turning as zero. Insert a Gyro Sensor block and set it to reset:
- Insert a Wait block right after the gyro reset. Set it to 2 seconds.
- In order for the robot to continue turning until 90 degrees is reached, a Loop must be used to constantly run the robot until the gyro sensor reads 90 degrees. Insert a loop after the wait block and set the end condition to be activated by the gyro sensor using Measure and Angle. Change the comparison to Greater Than and the value of the angle to 90 degrees.
- Insert a Motor block into the loop. Select the port that when activated will turn the robot to the right. Change the Motor type to Rotations and .05 rotations. This translates to the robot moving in .05 rotation increments until the gyro sensor reads 90 degrees:
- After the loop, insert a Steering block for the robot to travel straight one tile. Use either rotations or time to move the robot and duplicate the first part of the program after the motor block.
- Recreate the line following code to allow the robot to travel up the ramp. Test different values of power to overcome the ramp. The end statement should cause the robot to stop 10 cm away from the wall.
- Only parts provided in the EV3 kits are allowed (no regular Lego's)
- No "re-tests"
- There can be no modifications in hardware nor software between trials
For the values of %Acc and tolerance, the values must come from the Tabulation of Results from the same version of the robot, and the time is how long the robot took to complete Section 2 in seconds. The team with the highest Competition Ratio wins the competition:
The lab work is now complete. Please clean up the workstation. Return the robot to the TA in exchange for your SLDP robot kit. Also return all unused materials to the TA. Refer to the Assignment section for the instructions needed to prepare the lab report.
Individual Lab Report
Follow the lab report guidelines laid out in the page called Specifications for Writing Your Lab Reports in the Technical Communication section of this manual. The following discussion points should be addressed in the appropriate section of the lab report:
- Discuss product evaluation and the need for it.
- Discuss quality improvement and its importance.
- Explain why reverse engineering is important.
- Discuss a standard, an average, accuracy, and precision.
- Describe loops and switches and how they are useful in coding.
- Describe the light sensor, gyro sensor, and ultrasonic sensor used in the lab
- Discuss the importance of tolerance and %Acc in determining product quality.
- Discuss the EV3 kit and software used.
- Describe modifications of the robot between tests.
- Describe Mindstorms programming for parts of the lab utilizing sensors.
- Compare the final code with sensors and final code without sensors; determine which is better. Substantiate the decision with data, observations, and other facts collected.
- Make a final evaluation of the product: should it go into production? Describe its accuracy and precision.
- Assess the techniques used in the testing process.
- Discuss better testing methods for the robot design.
- Recommend if any design improvements should be made.
Remember: Lab notes must be taken. Experimental details are easily forgotten unless written down. EG1003 Lab Notes Paper can be downloaded and printed from the EG1003 Website. Use the lab notes to write the Procedure section of the lab report. At the end of each lab, a TA will scan the lab notes and upload them to the Lab Documents section of the EG1003 Website. One point of extra credit is awarded if the lab notes are attached at the end of the lab report. Keeping careful notes is an essential component of all scientific practice.
Team PowerPoint Presentation
Follow the presentation guidelines laid out in the page called EG1003 Lab Presentation Format in the Introduction to Technical Presentations section of this manual. When preparing the presentation, consider the following points:
- Based on the test results, what is the product's marketability?
- If determinations were negative, what improvements could be made?
- Why is product evaluation important?
- Discuss why quality improvement is important.
- Discuss the importance of utilizing sensors.