Difference between revisions of "Lemon Car Competition"

From EG1004 Lab Manual
Jump to: navigation, search
(1003 --> 1004)
 
(41 intermediate revisions by 3 users not shown)
Line 1: Line 1:
<h1 align=center>Lab 9: Lemon Car</h1>
<h2>Objectives</h2>


 
<p>The experimental objective of this lab is to use the principles of a reduction-oxidation reaction and see how a capacitor stores energy.
<h2>1 Objectives</h2>
 
<p>The experimental objective of this lab is to study the principles of a
reduction oxidation reaction, and to learn about how a capacitor stores energy.
</p>
</p>


<p>In order to learn how battery cells, capacitors and different reducing agents
<p>To observe how battery cells, capacitors and different reducing agents work, a lemon citrus cell will be constructed and used to power two different devices. </p>
work, we will construct a lemon citrus cell and use the cell to power two
different devices.</p>


<p>You will design and build a car that is powered either by a lemon battery or a
<p>You will design and build a car that is powered either by a lemon battery or a
capacitor (charged by a lemon battery). Your car will be entered in a competition
capacitor (charged by a lemon battery). Your car will be entered in a competition
against the other students’ cars in your section.</p>
against the other students' cars in your section.</p>


<h2>2 Overview</h2>
<h2>Overview</h2>


<h3>Chemistry behind a Citrus Cell</h3>
<h3>Chemistry behind a Citrus Cell</h3>


<p>A battery is a device that is usually made up of many individual cells. In
<p>A battery is a device that is usually made up of one or more individual cells.
this experiment we will be creating a citrus cell. A battery cell is a cell that
In this experiment we will be creating a citrus cell. A battery cell is a cell that
creates a voltage across a terminal of 2 dissimilar metals. This is done through
creates a voltage across a terminal of 2 dissimilar metals. This is done through
a chemical half reaction. A citrus cell is one that does this using a citrus
a chemical half reaction. A citrus cell is one that does this using a citrus
Line 32: Line 26:


<ul>
<ul>
<li>Electronegativity in an element is a measure of the element’s capability to
<li>Electronegativity in an element is a measure of the element's capability to
attract another element's electrons. The higher degree of electronegativity an element
attract another element's electrons. The higher degree of electronegativity an element
has the more power it has to pull away electrons from a less electronegative
has the more power it has to pull away electrons from a less electronegative
Line 46: Line 40:
</ul>
</ul>


<p align=center>[[Image: lemonlab_1.jpg]]</p>
[[Image: lemonlab_1.jpg|frame|center|Figure 1: Periodic Table Overview]]
 
<p class=caption>Figure 1: Periodic Table Overview</p>


<p>The electronegativity and ionization energy values for the metals used in the
<p>The electronegativity and ionization energy values for the metals used in the
Line 108: Line 100:
<p>These are the half-reactions of the magnesium and oxygen redox reaction. Be
<p>These are the half-reactions of the magnesium and oxygen redox reaction. Be
aware that the electrons in the half-reactions are not given a state, that is
aware that the electrons in the half-reactions are not given a state, that is
because they are being transferred and don’t have a definite state. If these
because they are being transferred and don't have a definite state. If these
reactions were separate then the electrons would have to travel through a wire
reactions were separate then the electrons would have to travel through a wire
or some medium to get to the other side, causing the two half-reactions to have
or some medium to get to the other side, causing the two half-reactions to have
Line 132: Line 124:
This means that current flow is in the opposite direction of electron flow.</p>
This means that current flow is in the opposite direction of electron flow.</p>


<p align=center>[[Image:lemonlab_2.jpg]]</p>
[[Image:lemonlab_2.jpg|frame|center|Figure 2: Daniell Cell]]
 
<p class=caption>Figure 2: Daniell Cell</p>


<p><i>Based on McGraw Hill Drawing</i></p>
<p><i>Based on McGraw Hill Drawing</i></p>


<h3>Electrochemical Cell- Daniell’s Cell</h3>
<h3>Electrochemical Cell- Daniell's Cell</h3>


<p>A type of electrochemical cell is shown above. The path of electron travel is
<p>A type of electrochemical cell is shown above. The path of electron travel is
shown clearly by the red line. This electrochemical cell is more specifically
shown clearly by the red line. This electrochemical cell is more specifically
called a Daniell’s Cell. There is a salt bridge separating the half-reactions.
called a Daniell's Cell. There is a salt bridge separating the half-reactions.
This salt bridge is present to provide each side with ions. Oxidation of <i>
This salt bridge is present to provide each side with ions. Oxidation of <i>
Zn</i> in the galvanic cell produces <i>Zn</i><sup>+ </sup>ions, also reduction
Zn</i> in the galvanic cell produces <i>Zn</i><sup>+ </sup>ions, also reduction
Line 149: Line 139:
not continue. The ions from the half-reaction would plate the other electrode,
not continue. The ions from the half-reaction would plate the other electrode,
and the reaction would slowly stop when the ions have finished plating the
and the reaction would slowly stop when the ions have finished plating the
opposite electrode. The reaction ‘poisons’ itself.</p>
opposite electrode. The reaction 'poisons' itself.</p>


<p align=center>[[Image:lemonlab_3.jpg]]</p>
[[Image:lemonlab_3.jpg|frame|center|Figure 3: Leclanché cell]]
 
<p class=caption>Figure 3: Leclanché cell</p>


<p><i>Reference: McGraw Hill</i></p>
<p><i>Reference: McGraw Hill</i></p>


<p>The concept of a Daniell’s Cell when applied to a commercial battery is
<p>The concept of a Daniell's Cell when applied to a commercial battery is
called the Leclanché cell. In a Leclanché cell there are two electrodes and an  
called the Leclanché cell. In a Leclanché cell there are two electrodes and an  
electrolyte and they are separated using a porous material. This material only  
electrolyte and they are separated using a porous material. This material only  
Line 168: Line 156:
different symbols. Below a few of them are shown:</p>
different symbols. Below a few of them are shown:</p>


<p align=center>[[Image:lemonlab_4.jpg]] [[Image:lemonlab_5.jpg]]</p>
<div><div style="float: left; display: inline;">[[Image:lemonlab_4.jpg|frame|none|Figure 4a: Cell]]</div><div style="width: 10%;float: left; display: inline;">&nbsp;</div><div style="float: left; display: inline;">[[Image:lemonlab_5.jpg|frame|none|Figure 4b: Battery]]</div></div><br clear="both" />
 
<p class=caption>Figure 4: Cell and Battery</p>


<p>A cell is a single unit for the conversion of chemical energy to electrical
<p>A cell is a single unit for the conversion of chemical energy to electrical
energy. A battery is comprised of multiple cells linked together. </p>
energy. A battery is comprised of multiple cells linked together. </p>


<p>A capacitor is an electrical device used to store charge temporarily. Because of
<p>A capacitor is an electrical device used to store charge temporarily. Some
their design, some capacitors are sensitive to the polarity of the voltage applied
capacitors can be used in place of a battery but they operate very differently
to them. The capacitors used in this lab must be connected with the proper polarity,
from one. A capacitor is charged by a voltage source logarithmically, as shown in
or they will fail. Therefore, be sure to check the capacitor used to make sure you
Figure 5.</p>
have the negative sign on the capacitor connected to the negative applied voltage.
 
Failure to do this will cause the capacitors to fail.</p>
[[Image:Lemonlab_13.png|frame|center|Figure 5: Capacitor Charging Curve]]
 
<p>Because of their design, these capacitors are sensitive to the polarity of
the voltage applied to them. The capacitors used in this lab must be connected
with the proper polarity, or they will fail. Therefore, be sure to check the
capacitor used to make sure you have the negative sign on the capacitor
connected to the negative applied voltage. Failure to do this will cause the
capacitors to fail.</p>
 
[[Image:lemonlab_9.jpg|frame|center|Figure 6: Polarized laboratory capacitor]]
 
<p> The total energy a capacitor holds is given by the equation <b>E=CV<sup>2</sup>/2</b>.
Note that the energy that the capacitor holds is proportional to the <b>square</b>
of the voltage.</p>
 
<p>A <b>diode</b> is a device that allows current to pass through it in only one direction.
This means that it has polarity, and will only allow current to pass from its positive
side to its negative side. a <b>Light Emitting Diode (LED)</b> not only passes current,
but also lights up when it's passing current.</p>
 
<p>A Light Emitting Diode is a semiconductor device, commonly referred as LED, that has the electrical characteristics of a diode with the additional characteristic of emitting light.</p>
 
<p>LEDs are fundamentally different from the incandescent lamps and the fluorescent lamps. Incandescent lamps use heat to generate light and fluorescent lamps use ionized gas. LEDs use the property of semiconductor conductivity at the atomic level. Electrons in the crystal structure are energized by the flow of electrical current across a semi-conductor junction of two or more slightly different materials. As the electrical current flows across the junction, some electrons in the crystal structure absorb energy. This absorbed energy is short lived and is released in the form of light. Different materials produce different colors.</p> 
<p>
LED s have a forward voltage and a reverse voltage. In the forward direction, the forward voltage and resistance are low and determined by the material used in the LED. The reverse voltage has a much higher resistance and a higher reverse voltage that prevents the flow of electrical current. The characteristic of the diode is to have low resistance to electrical flow in the forward direction and high residence in the reverse direction provides the ability to control the flow of electricity in one direction only.</p>
 
<p>There is a threshold voltage in the forward direction for the LED to emit light. Below the threshold voltage, there is no light. At and above the threshold voltage the LED emits light with intensity roughly linear with forward voltage. The symbol for the LED is shown in Figure 7.</p>
 
[[Image:Symbol_LED.png|frame|center|Figure 7: LED Symbol<sup>3</sup>]]
 
<p>Since each LED color is a characteristic of the specific materials used in the diode, each material has its own forward voltage, color and reverse voltage. The minimum forward voltage at which an LED will begin to emit light and its color are presented in Table 1.</p>
 
[[Image:LED_semiconductor.png|300px|frame|center|Table 1: Polarized laboratory capacitor<sup>4</sup>]]


<p>Different combinations of electrical components allow engineers to design
<p>Different combinations of electrical components allow engineers to design
Line 186: Line 204:
three different ways. In a series circuit, the element's conductors are
three different ways. In a series circuit, the element's conductors are
connected end to end. The current in a series circuit remains the same in all
connected end to end. The current in a series circuit remains the same in all
the electrical elements. In a serial circuit, as shown in Figure 4, the sum of
the electrical elements. In a series circuit, as shown in Figure 8, the sum of
the voltages across each element is equal to the voltage of the power source (
the voltages across each element is equal to the voltage of the power source (
<i>V<sub>out</sub> = V<sub>A</sub> + V<sub>B</sub> + V<sub>C</sub></i>).
<i>V<sub>out</sub> = V<sub>A</sub> + V<sub>B</sub> + V<sub>C</sub></i>).
</p>
</p>


<p align=center>[[Image:lemonlab_6.png]]</p>
[[Image:lemonlab_6.png|frame|center|Figure 8: A series circuit]]


<p class=caption>Figure 5: A series circuit</p>
<p>In a parallel circuit, as shown in Figure 9, the element's conductors are  
 
<p>In a parallel circuit, as shown in Figure 5, the element's conductors are  
connected at opposing ends. The current that is supplied by the voltage source  
connected at opposing ends. The current that is supplied by the voltage source  
equals the current that flows though elements <b><i>D</i></b> and <b><i>E</i>
equals the current that flows though elements <b><i>D</i></b> and <b><i>E</i>
Line 201: Line 217:
out</sub></i><i> = V<sub>D</sub> = V<sub>E</sub></i>)).</p>
out</sub></i><i> = V<sub>D</sub> = V<sub>E</sub></i>)).</p>


<p align=center>[[Image:lemonlab_7.png]]</p>
[[Image:lemonlab_7.png|frame|center|Figure 9: A parallel circuit]]
 
<p class=caption>Figure 6: A parallel circuit</p>
 
<p>Capacitors are devices that are used to store charge. They can be used in place
of a battery but they operate very differently from one. A capacitor is charged by
a voltage source exponentially. The time constant is the standard unit of time for
a capacitor to charge to 63%. It is shown by the formula
<b><font face=Symbol>&tau;</font>=CV/I.</b></p>
 
<p>However capacitors do not charge linearly, so for each subsequent interval
of <b><font face=Symbol>&tau;</font></b> the capacitor will accumulate less energy. See the following chart.</p>
 
<table border=1 cellspacing=0 align=center>
<tr><td><b>Time, <font face=Symbol><i>&tau;</i></font></b></td><td><b>%Charged</b></td></tr>
<tr><td><font face=Symbol><i>&tau;</i></font></td><td>63%</td></tr>
<tr><td>2<font face=Symbol><i>&tau;</i></font></td><td>86%</td></tr>
<tr><td>3<font face=Symbol><i>&tau;</i></font></td><td>95%</td></tr>
<tr><td>4<font face=Symbol><i>&tau;</i></font></td><td>98%</td></tr>
<tr><td>5<font face=Symbol><i>&tau;</i></font></td><td>99%</td></tr>
</table>
 
<p class=caption>Chart 1: Time versus % charged.</p>
 
<p>When a capacitor is fully charged, it does not matter what the current was when it was
charged. It will output the energy contained in the capacitor when it is charged. In
effect you can trickle-charge a capacitor and discharge the accumulated energy at a higher
rate in a short period of time.</p>
 
<p align=center>[[Image:lemonlab_9.jpg]]</p>
 
<p class=caption>Figure 7: Polarized laboratory capacitor</p>


<p>The motor provided is a 9V motor that will operate with voltages lower than 9V with
<p>The motor provided is a 9V motor that will operate with voltages lower than 9V with
Line 239: Line 224:
the motor speed. By increasing current you increase the torque.</p>
the motor speed. By increasing current you increase the torque.</p>


<h2>3 YOUR ASSIGNMENT</h2>
<h2>Design Considerations</h2>
 
* Which electrode pair yields the most voltage per unit cost?
<h3>Team Lab Report</h3>
* Which circuit configuration will provide a more desirable voltage across the load? Parallel or series?
 
* Which aspects of the competition formula are most advantageous?
<p><b>Note:</b> Since this lab is a competition, you will be writing a team lab report rather than an
individual one. See the <i>Team Authoring Strategies</i> page in the <i>Technical Communication</i> of
this online manual for guidance of how to do this.</p>
 
<p>Follow the lab report guidelines laid out in the page called <i>Specifications for
Writing Your Lab Reports</i> in the <i>Technical Communication</i> section of this manual.
As you write, the following discussion points should be addressed in the appropriate
section of your lab report:</p>


<ul>
<h2>Materials and Equipment</h2>
<li>Describe the electrochemical cell in your introduction. What consequences
did the electrode voltages have for your design decisions? Use appropriate part
1 experimental values.</li>
 
<li>What factors did you consider in designing your Lemon-Powered Car? Did you
use any of the background information?</li>
 
<li>What was the competition ratio for your design?</li>
 
<li>What important design characteristics should a winning Lemon-Powered Car
include to achieve the highest possible design ratio?</li>
 
<li>Describe how your power source design succeeded or failed.</li>
 
<li>Discuss design improvements. How would you optimize the design (i.e.
improve the ratio) based on experience?</li>
 
<li>Describe the concept behind the lemon battery.</li>
</ul>
 
<h3>Team PowerPoint Presentation</h3>
 
<p>Follow the presentation guidelines laid out in the page called <i>EG1004 Lab Presentation
Format</i> in the <i>Introduction to Technical Presentations</i> section of this manual.
When you are preparing your presentation, consider the following points:</p>
 
<ul>
<li>What recommendation should be considered for improvements of the lemon-powered car?</li>
<li>Discuss the difference in design of the three vehicles you worked with (Lego Car,
Mousetrap Car, Lemon-Powered Car)</li>
</ul>
 
<h2>4 Materials and Equipment</h2>
<ul>
<ul>
  <li>Lemons<u></u></li>
  <li>Lemons<u></u></li>
Line 305: Line 249:
  <li>Paper/styrofoam Plates</li>
  <li>Paper/styrofoam Plates</li>
</ul>
</ul>
<h3>Materials with Price List (Part 3)</h3>
* Capacitor: $1.00
* 2oz Lemon Juice (with cup): $0.25
* 1.5" Mg Strips: $1.00
* Cu Strip: $0.25
* Zn Strip: $0.50
* Al Strip: $0.25
* Ni Strip: $0.25
* Lemon Car Components: $0.00


<p><b><font color=#ff0000>Warning:</font> Magnesium is a highly reactive metal. Use carefully
<p><b><font color=#ff0000>Warning:</font> Magnesium is a highly reactive metal. Use carefully
and only as described in these instructions.</b></p>
and only as described in these instructions.</b></p>


<h2>5 Procedure</h2>
<h2>Procedure</h2>


<p><b>NOTE:</b> This lab makes use of liquids. Please do as much work as possible on the
<p><b>NOTE:</b> This lab makes use of liquids. Please do as much work as possible on the
Line 315: Line 268:


<h3>Part 1: Determine Voltage output of different metal electrode pairs</h3>
<h3>Part 1: Determine Voltage output of different metal electrode pairs</h3>
<p><b>Remember: </b><i>You are required to take notes. Experimental details
are easily forgotten unless written down. You should keep a laboratory notebook
for this purpose. Use your lab notes to write the Procedure section of your
lab report. You <b>must </b>attach a copy of your lab notes to the <b>WC </b>
copy of your lab report. Keeping careful notes is an essential component of
all scientific practice.</i></p>


<ol>
<ol>
<li>Obtain two different samples of metals from your TA (two each). TA’s will
<li>Obtain two different samples of metals from your TA (two each). TA's will
select different metal combinations for each team.</li>
select different metal combinations for each team.</li>


Line 330: Line 276:
is released, without puncturing the lemon.</li>
is released, without puncturing the lemon.</li>


<li>Insert one of the metals into the lemon.</li>
<li>Before inserting one of the metal strips into the lemon, be sure to clean the metal
strips. Using emery paper provided by your TA, scrub the emery paper on the metal strip
in one direction several times. Then, scrub the metal strip in the direction
perpendicular to the direction before. Now that they are clean, insert one metal into
the lemon.</li>


<li>Half a centimeter away insert the other metal piece parallel to the first,
<li>Half a centimeter away insert the other metal piece parallel to the first,
so that they are close but do not touch.</li>
so that they are close but do not touch.</li>


<p align=center>[[Image:lemonlab_10.jpg]]</p>
[[Image:lemonlab_10.jpg|frame|center|Figure 10: Lemon Cell]]
 
<p class=caption>Figure 8: Lemon Cell</p>


<li>Connect one end of the first alligator cable set to one of the metal pieces
<li>Connect one end of the first alligator cable set to one of the metal pieces
Line 363: Line 311:


<h3>Part 2: Light up LED and verify polarity</h3>
<h3>Part 2: Light up LED and verify polarity</h3>
<li>First, you need to test if your LED works.</li>


<li>Repeat steps 2-4 in Part 1 to create a second citrus cell.</li>
<li>Repeat steps 2-4 in Part 1 to create a second citrus cell.</li>
Line 368: Line 318:
<li>Insert the metals into the first lemon to reactivate the first citrus cell.</li>
<li>Insert the metals into the first lemon to reactivate the first citrus cell.</li>


<li>Connect the first lemon’s anode to the second lemon’s cathode using the
<li>Connect the first lemon's anode to the second lemon's cathode using the
alligator cable set. Now you have created a lemon battery.</li>
alligator cable set. Now you have created a lemon battery.</li>


Line 377: Line 327:




<p align=center>[[Image:lemonlab_11.jpg]]</p>
[[Image:lemonlab_11.jpg|frame|center|Figure 11: Light Emitting Diode (LED)- note polarization]]
 
<p class=caption>Figure 9: Light Emitting Diode (LED)- note polarization</p>


<li>Now connect the LED to the lemon battery in the right polarity. Place a hand
<li>Now connect the LED to the lemon battery in the right polarity. Place a hand
Line 398: Line 346:
<li>Assess your materials and consider the data established from Part 1. Choose
<li>Assess your materials and consider the data established from Part 1. Choose
materials for your lemon car design, keeping in mind the Competition Ratio. Make
materials for your lemon car design, keeping in mind the Competition Ratio. Make
sure you take notes and make preliminary sketches during this process.</li>
sure you make preliminary sketches during this process.</li>


<li>For your convenience lemon juice and small cups will be provided for this
<li>For your convenience lemon juice and small cups will be provided for this
Line 405: Line 353:
Lemons have membranes that limit chemical reactions.</li>
Lemons have membranes that limit chemical reactions.</li>


<li>You will be given a standard chassis for your lemon car. A set of diagrams showing
<li>Since your lemon car can be powered by either a lemon battery or a (lemon battery
the construction of hte standard chassis is shown at the end of this lab page.
Since your lemon car can be powered by either a lemon battery or a (lemon battery
charged) capacitor you may modify it any way you deem fit. Sketch your design in pencil
charged) capacitor you may modify it any way you deem fit. Sketch your design in pencil
using the graph paper provided on the EG website http://eg.poly.edu. Label your
using the graph paper provided on the EG website http://eg.poly.edu. Label your
Line 420: Line 366:
</ol>
</ol>


<h2>6 Competition</h2>
<li>Before entering the competition, test if your motor is working.</li>
 
<h2>Competition</h2>


<p>Since your lemon car can be powered by either a lemon battery or a (lemon
<p>Since your lemon car can be powered by a lemon battery, a (lemon
battery charged) capacitor the start procedures for the competition are different.</p>
battery charged) capacitor, or a combination of both, the start procedures for the competition are different.</p>


<p>For the lemon battery, start the chemical process by pouring lemon juice into
<p>For the lemon battery, start the chemical process by pouring lemon juice into
Line 437: Line 385:
</p>
</p>


<p>[[Image:lemonlab_12.gif]]</p>
<math>CR = \frac{distance\left[\text{ft}\right]}{1\left[\text{s}\right] + time\left[\text{s}\right]} \times \frac{100}{Cost\left[$\right]} + distance\left[\text{ft}\right]\,</math>


<p>The TA will record the test data after 60 seconds or when the car stops moving,
<p>The TA will record the test data after 60 seconds or when the car stops moving,
whichever occurs first. The TA will then calculate the competition ratio. The
whichever occurs first. The linear distance from the starting point will be measured. The TA will then calculate the competition ratio. The
tabulation for the whole class will be provided.</p>
tabulation for the whole class will be provided.</p>
<h2>7 Data Analysis</h2>


<p>Your lab work is now complete. Please clean up your workstation. Return all
<p>Your lab work is now complete. Please clean up your workstation. Return all
unused materials to your TA. Refer to section <b><i>Your Assignment </i></b>for
unused materials to your TA. Refer to section <b><i>Your Assignment </i></b>for
the instructions you need to prepare your lab report. </p>
the instructions you need to prepare your lab report. </p>
<h2>ASSIGNMENT</h2>
<h3>Team Lab Report</h3>
<p><b>Note:</b> Since this lab is a competition, you will be writing a team lab report rather than an
individual one. See the [[Team Authoring Strategies]] page in the <i>Technical Communication</i> of
this online manual for guidance of how to do this.</p>
<p>Follow the lab report guidelines laid out in the page called
[[Specifications for Writing Your Lab Reports]] in the <i>Technical Communication</i>
section of this manual. As you write, the following discussion points should be addressed
in the appropriate section of your lab report:</p>
<ul>
<li>Describe the electrochemical cell in your introduction. What consequences
did the electrode voltages have for your design decisions? Use appropriate part
1 experimental values.</li>
<li>What factors did you consider in designing your Lemon-Powered Car? Did you
use any of the background information?</li>
<li>Include what background information was used to aid in your design</li>
<li>What was the competition ratio for your design?</li>
<li>What important design characteristics should a winning Lemon-Powered Car
include to achieve the highest possible design ratio?</li>
<li>Describe how your power source design succeeded or failed.</li>
<li>Discuss design improvements. How would you optimize the design (i.e.
improve the ratio) based on experience?</li>
<li>Describe the concept behind the lemon battery.</li>
<li>Describe the power source chosen for the design.
<li>Include spreadsheet with every team's results. Describe the results and talk about other designs in the class.
</ul>
{{Lab notes}}
<h3>Team PowerPoint Presentation</h3>
<p>Follow the presentation guidelines laid out in the [[EG1004 Lab Presentation Format]] section of this manual.
When you are preparing your presentation, consider the following points:</p>
<ul>
<li>Since one term in the competition ratio is cost, present the cost of your vehicle.
Use the page [[How to Show Cost Data in Presentations]] for instructions on how to do
this.</li>
<li>How would you improve your lemon-powered car?</li>
</ul>


<h2>Footnotes</h2>
<h2>Footnotes</h2>
Line 457: Line 456:
{http://en.wikipedia.org/wiki/Electrode}</p>
{http://en.wikipedia.org/wiki/Electrode}</p>


<h2>Appendix: Assembly of the Standard Chassis</h2>
<p><sup>3</sup> Retrieved June 20, 2017, from {http://www.electronics-tutorials.ws/diode/diode_8.html} </p>


<h3>1.</h3>
<p><sup>4</sup> File:Symbol LED.svg. (n.d.). Retrieved June 20, 2017, from {https://commons.wikimedia.org/wiki/File:Symbol_LED.svg}</p>
<p>[[Image:lemonlab_21.jpg]]</p>
<h3>2.</h3>
<p>[[Image:Lemonlab_22.jpg]]</p>
<h3>3.</h3>
<p>[[Image:Lemonlab_23.jpg]]</p>
<h3>4.</h3>
<p>[[Image:Lemonlab_24.jpg]]</p>
<h3>5.</h3>
<p>[[Image:Lemonlab_25.jpg]]</p>
<h3>6.</h3>
<p>[[Image:Lemonlab_26.jpg]]</p>
<h3>7.</h3>
<p>[[Image:Lemonlab_27.jpg]]</p>
<h3>8.</h3>
<p>[[Image:Lemonlab_28.jpg]]</p>


<p>[[Main_Page | Return to Table of Contents]]</p>
<p>[[Main_Page | Return to Table of Contents]]</p>

Latest revision as of 02:29, 31 August 2022

Objectives

The experimental objective of this lab is to use the principles of a reduction-oxidation reaction and see how a capacitor stores energy.

To observe how battery cells, capacitors and different reducing agents work, a lemon citrus cell will be constructed and used to power two different devices.

You will design and build a car that is powered either by a lemon battery or a capacitor (charged by a lemon battery). Your car will be entered in a competition against the other students' cars in your section.

Overview

Chemistry behind a Citrus Cell

A battery is a device that is usually made up of one or more individual cells. In this experiment we will be creating a citrus cell. A battery cell is a cell that creates a voltage across a terminal of 2 dissimilar metals. This is done through a chemical half reaction. A citrus cell is one that does this using a citrus juice as the electrolytic solution. By using 2 different types of metals we have 2 different reaction potentials which directly affect the voltage produced with each cell. By linking multiple cells together in series we produce a battery.

Before learning the concept behind a battery cell, there are two properties that should be understood: electronegativity and ionization energy:

  • Electronegativity in an element is a measure of the element's capability to attract another element's electrons. The higher degree of electronegativity an element has the more power it has to pull away electrons from a less electronegative element. There is an obvious trend in the periodic table for this particular property. Electronegativity generally increases from left to right and from bottom to top. As a result the elements around cesium have very low electronegativity and elements around fluorine have the highest.
  • Ionization energy is the amount of energy required to remove an electron from an atom to form a cation. A cation is an ion or group of ions having a positive charge in electrolysis. This property also has a trend in the periodic table. It generally increases from left to right and from bottom to top.
Figure 1: Periodic Table Overview

The electronegativity and ionization energy values for the metals used in the lab are provided in the table below:

Metal Electronegativity
(Pauling Scale)
Ionization Energy
(kJ/mole)
Magnesium 1.31 738
Nickel 1.91 736
Copper 1.90 745
Zinc 1.65 904
Aluminum 1.61 577

These two properties give the metals their reactive traits.

The reaction that takes place in the lemon cell is called a redox reaction. This reaction can be simplified into two parts and they are called oxidation and reduction. Oxidation happens when there is an electron loss and reduction is when there is an electron gain. Oxidation and reduction can be shown in a half-reaction, which clearly shows the electron transfer. Take for example the redox reaction between magnesium and oxygen.

2Mg(s) + O2(g) → 2MgO2(s)

When magnesium reacts with oxygen, magnesium loses electrons making it oxidized:

Mg(s) → Mg2 + (s) + 2e-

At the same time, oxygen gains those electrons making oxygen reduced.

O2(g) + 4e- → 2O2-(g)

These are the half-reactions of the magnesium and oxygen redox reaction. Be aware that the electrons in the half-reactions are not given a state, that is because they are being transferred and don't have a definite state. If these reactions were separate then the electrons would have to travel through a wire or some medium to get to the other side, causing the two half-reactions to have a potential between each other. This potential is the voltage between the two half-reactions.

An electrochemical cell is where two electrodes are in contact with an electrolyte. The electrodes are conductors (usually metallic) used to form a contact with a nonmetallic part of a circuit such as an electrolyte.2 The electrolyte provides an abundance of ions to the reaction. The electrode at which oxidation occurs is called the anode and is the source of electrons that flow inside the cell. This creates a shortage of electrons at the electrode, so the anode is the positive part of the cell. The electrode at which reduction occurs is called the cathode and is the destination of these electrons. This creates a surplus of electrons at the electrode, so the cathode is the negative part of the cell.

Looking at the cell externally, this means that the cell supplies electrons at the cathode, the electrons flow through whatever the cell is powering, and are collected at the anode. Early scientists understood the concept of the flow of current, but did not know about electrons, so they arbitrarily said that electrical current is defined to flow from the positive (anode) to the negative (cathode) electrodes of a battery. This means that current flow is in the opposite direction of electron flow.

Figure 2: Daniell Cell

Based on McGraw Hill Drawing

Electrochemical Cell- Daniell's Cell

A type of electrochemical cell is shown above. The path of electron travel is shown clearly by the red line. This electrochemical cell is more specifically called a Daniell's Cell. There is a salt bridge separating the half-reactions. This salt bridge is present to provide each side with ions. Oxidation of Zn in the galvanic cell produces Zn+ ions, also reduction of Cu- ions. Without the salt bridge to connect the half-reactions and bring ions the reactions would not continue. The ions from the half-reaction would plate the other electrode, and the reaction would slowly stop when the ions have finished plating the opposite electrode. The reaction 'poisons' itself.

Figure 3: Leclanché cell

Reference: McGraw Hill

The concept of a Daniell's Cell when applied to a commercial battery is called the Leclanché cell. In a Leclanché cell there are two electrodes and an electrolyte and they are separated using a porous material. This material only lets the ions pass through, therefore preventing direct interaction of the two half-reactions.1

Electrical Components

In electrical engineering different electrical components are represented by different symbols. Below a few of them are shown:

Figure 4a: Cell
 
Figure 4b: Battery


A cell is a single unit for the conversion of chemical energy to electrical energy. A battery is comprised of multiple cells linked together.

A capacitor is an electrical device used to store charge temporarily. Some capacitors can be used in place of a battery but they operate very differently from one. A capacitor is charged by a voltage source logarithmically, as shown in Figure 5.

Figure 5: Capacitor Charging Curve

Because of their design, these capacitors are sensitive to the polarity of the voltage applied to them. The capacitors used in this lab must be connected with the proper polarity, or they will fail. Therefore, be sure to check the capacitor used to make sure you have the negative sign on the capacitor connected to the negative applied voltage. Failure to do this will cause the capacitors to fail.

Figure 6: Polarized laboratory capacitor

The total energy a capacitor holds is given by the equation E=CV2/2. Note that the energy that the capacitor holds is proportional to the square of the voltage.

A diode is a device that allows current to pass through it in only one direction. This means that it has polarity, and will only allow current to pass from its positive side to its negative side. a Light Emitting Diode (LED) not only passes current, but also lights up when it's passing current.

A Light Emitting Diode is a semiconductor device, commonly referred as LED, that has the electrical characteristics of a diode with the additional characteristic of emitting light.

LEDs are fundamentally different from the incandescent lamps and the fluorescent lamps. Incandescent lamps use heat to generate light and fluorescent lamps use ionized gas. LEDs use the property of semiconductor conductivity at the atomic level. Electrons in the crystal structure are energized by the flow of electrical current across a semi-conductor junction of two or more slightly different materials. As the electrical current flows across the junction, some electrons in the crystal structure absorb energy. This absorbed energy is short lived and is released in the form of light. Different materials produce different colors.

LED s have a forward voltage and a reverse voltage. In the forward direction, the forward voltage and resistance are low and determined by the material used in the LED. The reverse voltage has a much higher resistance and a higher reverse voltage that prevents the flow of electrical current. The characteristic of the diode is to have low resistance to electrical flow in the forward direction and high residence in the reverse direction provides the ability to control the flow of electricity in one direction only.

There is a threshold voltage in the forward direction for the LED to emit light. Below the threshold voltage, there is no light. At and above the threshold voltage the LED emits light with intensity roughly linear with forward voltage. The symbol for the LED is shown in Figure 7.

Figure 7: LED Symbol3

Since each LED color is a characteristic of the specific materials used in the diode, each material has its own forward voltage, color and reverse voltage. The minimum forward voltage at which an LED will begin to emit light and its color are presented in Table 1.

Table 1: Polarized laboratory capacitor4

Different combinations of electrical components allow engineers to design different devices. Resistors, inductors, and capacitors can be arranged in three different ways. In a series circuit, the element's conductors are connected end to end. The current in a series circuit remains the same in all the electrical elements. In a series circuit, as shown in Figure 8, the sum of the voltages across each element is equal to the voltage of the power source ( Vout = VA + VB + VC).

Figure 8: A series circuit

In a parallel circuit, as shown in Figure 9, the element's conductors are connected at opposing ends. The current that is supplied by the voltage source equals the current that flows though elements D and E . The voltage across the elements that are parallel is the same (V out = VD = VE)).

Figure 9: A parallel circuit

The motor provided is a 9V motor that will operate with voltages lower than 9V with reduced torque and speed. A motor with no load draws 9 milliamps; a stalled motor draws well over 350 milliamps. By increasing the voltage provided to the motor you can increase the motor speed. By increasing current you increase the torque.

Design Considerations

  • Which electrode pair yields the most voltage per unit cost?
  • Which circuit configuration will provide a more desirable voltage across the load? Parallel or series?
  • Which aspects of the competition formula are most advantageous?

Materials and Equipment

  • Lemons
  • Lemon Juice
  • Magnesium
  • Nickel
  • Zinc
  • Copper
  • Aluminum
  • 3 Alligator cable sets
  • 1 Farad 2.5V Capacitor
  • Standard Lego Car Chassis plus Lego parts kit
  • Lego to Alligator Cable Clip Connector
  • LED (Light Emitting Diode)
  • Small cups
  • Scissors
  • Tape
  • DMM (Digital Multi-meter)
  • Paper/styrofoam Plates

Materials with Price List (Part 3)

  • Capacitor: $1.00
  • 2oz Lemon Juice (with cup): $0.25
  • 1.5" Mg Strips: $1.00
  • Cu Strip: $0.25
  • Zn Strip: $0.50
  • Al Strip: $0.25
  • Ni Strip: $0.25
  • Lemon Car Components: $0.00

Warning: Magnesium is a highly reactive metal. Use carefully and only as described in these instructions.

Procedure

NOTE: This lab makes use of liquids. Please do as much work as possible on the tray/plate provided and wipe up spills immediately.

Part 1: Determine Voltage output of different metal electrode pairs

  1. Obtain two different samples of metals from your TA (two each). TA's will select different metal combinations for each team.
  2. Take the lemon and squeeze/roll it so that the lemon juice inside the pulp is released, without puncturing the lemon.
  3. Before inserting one of the metal strips into the lemon, be sure to clean the metal strips. Using emery paper provided by your TA, scrub the emery paper on the metal strip in one direction several times. Then, scrub the metal strip in the direction perpendicular to the direction before. Now that they are clean, insert one metal into the lemon.
  4. Half a centimeter away insert the other metal piece parallel to the first, so that they are close but do not touch.
  5. Figure 10: Lemon Cell
  6. Connect one end of the first alligator cable set to one of the metal pieces and one end of the second alligator cable set to the other metal. These will be the electrodes of the cell.
  7. Connect the other ends of the alligator cable sets to the positive and negative ends of the digital multi-meter and measure the voltage. Record the value in units of volts. (Note: If it is negative then the polarity is switched, switch the alligator clips to connect to the opposite sides of the DMM)
  8. The metal strip attached to the positive end of the digital multi-meter (red wire) is the anode (+) and the other (black wire) is the cathode (-).
  9. Record the values and present them to your TA. The TA will generate a spreadsheet with the voltage produced by each metal combination for all teams.
  10. Remove the electrodes to stop the chemical reaction. Wipe them clean with a paper towel. Discard the paper towel in the trash can.
  11. Warning: magnesium left in the lemon juice dissolves.

    Part 2: Light up LED and verify polarity

  12. First, you need to test if your LED works.
  13. Repeat steps 2-4 in Part 1 to create a second citrus cell.
  14. Insert the metals into the first lemon to reactivate the first citrus cell.
  15. Connect the first lemon's anode to the second lemon's cathode using the alligator cable set. Now you have created a lemon battery.
  16. Measure the voltage in the lemon battery using the digital multi-meter and record it. Following the formula for linking batteries in series, the voltage should be doubled. If it is lower try taking the electrodes out and plunging them into a different part of the lemon.
  17. Figure 11: Light Emitting Diode (LED)- note polarization
  18. Now connect the LED to the lemon battery in the right polarity. Place a hand over the LED and observe it to see if you see any light. If it does not light connect a third lemon cell in series. Does it light up? Why or why not?
  19. Clean and return all electrodes.
  20. Part 3: Lemon Powered Car Design

    Your car must be designed/built to enter the lab competition. The power must come from either an on-board lemon battery (4 cells maximum) or an on-board capacitor (previously charged from a lemon battery). The car designed for the lemon battery will obviously be larger and heavier than one designed for the capacitor.

     

  21. Assess your materials and consider the data established from Part 1. Choose materials for your lemon car design, keeping in mind the Competition Ratio. Make sure you make preliminary sketches during this process.
  22. For your convenience lemon juice and small cups will be provided for this portion of the lab. You may cut the cups to reduce weight and somehow fasten the electrodes. The lemon juice will provide a better electrolytic solution than a lemon. Lemons have membranes that limit chemical reactions.
  23. Since your lemon car can be powered by either a lemon battery or a (lemon battery charged) capacitor you may modify it any way you deem fit. Sketch your design in pencil using the graph paper provided on the EG website http://eg.poly.edu. Label your drawings clearly. Prepare a price-list for your lemon powered car based on the materials you have chosen. Use the results your class determined from Part 1 of the experiment. Have your TA sign the sketches and the price-list.
  24. Your TA will provide the materials needed for your design. If you decide to modify your design during the construction of your car, note the changes and describe the reasons for them. If the modifications required more materials to be used, make sure you update your price list and your TA approves it.
  • Before entering the competition, test if your motor is working.
  • Competition

    Since your lemon car can be powered by a lemon battery, a (lemon battery charged) capacitor, or a combination of both, the start procedures for the competition are different.

    For the lemon battery, start the chemical process by pouring lemon juice into the cups. For the capacitor, make sure that it has been charged for at least 15 minutes according to the instructions in Part 3, and be careful to not short out the capacitor --- it will take another 15 minutes to recharge.

    When requested by the TA, the student will position the lemon powered car and either allow the car to run (lemon battery design) or connect the alligator clips to the capacitor (capacitor design).

    The competition will be won by the team that has the highest competition ratio:

    The TA will record the test data after 60 seconds or when the car stops moving, whichever occurs first. The linear distance from the starting point will be measured. The TA will then calculate the competition ratio. The tabulation for the whole class will be provided.

    Your lab work is now complete. Please clean up your workstation. Return all unused materials to your TA. Refer to section Your Assignment for the instructions you need to prepare your lab report.

    ASSIGNMENT

    Team Lab Report

    Note: Since this lab is a competition, you will be writing a team lab report rather than an individual one. See the Team Authoring Strategies page in the Technical Communication of this online manual for guidance of how to do this.

    Follow the lab report guidelines laid out in the page called Specifications for Writing Your Lab Reports in the Technical Communication section of this manual. As you write, the following discussion points should be addressed in the appropriate section of your lab report:

    • Describe the electrochemical cell in your introduction. What consequences did the electrode voltages have for your design decisions? Use appropriate part 1 experimental values.
    • What factors did you consider in designing your Lemon-Powered Car? Did you use any of the background information?
    • Include what background information was used to aid in your design
    • What was the competition ratio for your design?
    • What important design characteristics should a winning Lemon-Powered Car include to achieve the highest possible design ratio?
    • Describe how your power source design succeeded or failed.
    • Discuss design improvements. How would you optimize the design (i.e. improve the ratio) based on experience?
    • Describe the concept behind the lemon battery.
    • Describe the power source chosen for the design.
    • Include spreadsheet with every team's results. Describe the results and talk about other designs in the class.

    Remember: Lab notes must be taken. Experimental details are easily forgotten unless written down. EG1004 Lab Notes Paper can be downloaded and printed from the EG1004 Website. Use the lab notes to write the Procedure section of the lab report. At the end of each lab, a TA will scan the lab notes and upload them to the Lab Documents section of the EG1004 Website. One point of extra credit is awarded if the lab notes are attached at the end of the lab report. Keeping careful notes is an essential component of all scientific practice.

    Team PowerPoint Presentation

    Follow the presentation guidelines laid out in the EG1004 Lab Presentation Format section of this manual. When you are preparing your presentation, consider the following points:

    • Since one term in the competition ratio is cost, present the cost of your vehicle. Use the page How to Show Cost Data in Presentations for instructions on how to do this.
    • How would you improve your lemon-powered car?

    Footnotes

    1 Atkins, P.W., Beran, J.A.. General Chemistry(second edition). American Books, 1989

    2 Wikipedia. 16 Aug. 2005 {http://en.wikipedia.org/wiki/Electrode}

    3 Retrieved June 20, 2017, from {http://www.electronics-tutorials.ws/diode/diode_8.html}

    4 File:Symbol LED.svg. (n.d.). Retrieved June 20, 2017, from {https://commons.wikimedia.org/wiki/File:Symbol_LED.svg}

    Return to Table of Contents