Heat Transfer and Thermal Insulation Competition

EG1004 Lab 8: Heat Transfer and Thermal Insulation

1 OBJECTIVES

The experimental objective of this lab is to design and build a container that minimizes the heat lost by an egg placed inside.

Furthermore, you will learn about heat as a form of energy (thermal energy) and how it is transferred. We will also investigate the principles of minimal design. Your design will be entered in a competition against the other containers in your section. The team with the lowest Minimal Design Ratio (MDR) will be declared the winner.

Note: Be sure to read the calculation of the MDR near the end of the lab before you start your design.

2 OVERVIEW

Heat is a form of energy. Heat transfer is thermal energy that is transferred from one body to another as a result of a temperature difference. Temperature is the measure of the average kinetic energy of atomic motion. The faster the atoms are moving, the higher the temperature. In this lab, we will focus on the ways heat is transferred.

The specific mechanisms that convey energy from one location to another are conduction, convection, and radiation. If you put any two objects with different temperatures together, heat will be transferred from the object with the higher temperature to the one with the lower temperature until the system reaches equilibrium. Let's say you placed a hot bowl of soup on the kitchen table. What would happen? What if you placed a glass of ice water on the same table? Our job is to understand how this heat transfer occurs and how to slow the process down.

When there is a temperature difference within a solid body or between two solid bodies in contact with each other, energy (heat) will flow from the region of higher temperature to the region of lower temperature. This is known as conduction. The formula to determine the conductivity in a rod of material is:

In this equation, Q is heat transferred in time t, k is the thermal conductivity constant, A is area, T is temperature and d is the thickness of the barrier. Therefore, increasing d or decreasing A would reduce conduction.

Imagine a metal rod that is heated at one end. The atoms of the rod collide at the point where the temperature differs, transferring heat until the temperature of the rod becomes uniform.

Convection is the transfer of heat within a fluid medium (fluids consist of gasses and liquids). Convection can occur in two different ways. The first way is known as natural convection. Natural convection occurs when the main mechanism for heat transfer is due to the temperature difference either within the fluid or at its boundaries. This difference in temperature causes the molecules in the higher temperature region to expand and rise due to buoyant forces. See Figure 1 for a diagram of natural convection. The second way in which convection occurs is called forced convection. Forced convection occurs when the main mechanism for heat transfer is due to the forced flow or motion of the fluid.

Figure 1: Air circulation diagram

Today we heat our homes through radiators using natural convection. Air flows through a heating element and then is dispersed through the room. Would it be helpful to put bigger fins on the heating element? To decide, use the formula for heat transferred through convection:

In this equation, Q is the heat transferred in time t, ∆T is the difference in temperature, h is the convection coefficient, and A is the surface area.

Suppose you wanted to disperse the heat even faster. In that case you could blow a fan past the heating elements. This is forced convection; it is one of the principles used in air conditioners to have a relatively small unit cool a large space.

According to the Encyclopedia Britannica, radiation is the process by which energy, in the form of electromagnetic radiation, is emitted by a heated surface in all directions. It travels to its point of absorption at the speed of light and does not require an intervening medium to carry it. The heating of the Earth by the Sun is an example of heat transfer by radiation. The formula for heat transferred through radiation:

In this equation, Q is the heat transferred in time t, T_s is the surface absolute temperature, e is the constant of emissivity, T_sur is the surrounding absolute temperature, A is the surface area, and σ is the Stefan-Boltzmann constant.

Electromagnetic radiation is a mean of energy transfer that occurs when an atom absorbs energy. As we have seen earlier when heated atomic motion within a body increases. The energy absorbed by the atom causes some of its electrons to move around. For sake of stability, the electrons eventually come to its original state or position creating an electromagnetic wave. This EM wave can propagate as heat, light, ultraviolet, or other electromagnetic waves depending on the type of atom and the amount of energy absorbed.

Color is a property of light which is based on the frequency of the wave. When we see a specific color, our eyes literally receive an electromagnetic wave of a specific frequency. Materials that appear lighter (i.e. yellow) reflect more light (EM waves of a specific frequency) than darker ones. Following the same logic, when an object appears white, it virtually reflect all the EM waves coming to it while a "black" object absorbs it all.

Therefore, color (reflectivity) is to be taken into account when choosing materials for thermal insulation.

How would you feel out in the sun on hot day in a black t-shirt? How would you feel if your shirt were white? A black surface is an excellent absorber of heat, while a white surface is not. Silver is a poor heat absorber and reflects radiated energy; that is why rooftops of apartment houses are often painted silver.

Your container is a thermodynamic system – a part of the Universe separated from the surroundings by an imaginary boundary. There are three types of systems: open systems, closed systems and isolated systems.

Open systems are systems where transfer of mass and heat is possible. For example, an open pot of boiling water is an open system – it exchanges heat with the air around it and water vapor. If collected, the water vapor can be condensed back to liquid water which has some mass.

Closed systems are systems where only heat can be transferred to the surroundings. A hermetically sealed bottle of soda is a closed system. If placed in a hot environment it absorbs energy in form of heat but the amount of liquid within does not change.

Isolated systems are systems which do not interact with the surroundings at all. No exchange is possible - neither heat nor mass. An ideal Thermos® is an isolated system. If hot chocolate is poured within, you will get the same amount back at the same temperature. No such system can be fabricated but can be approximated.

Now that we understand how heat is transferred, we must consider how to slow it down. Understanding how to minimize heat loss is the key to designing a successful insulating container.

The first consideration is the materials you choose. Using materials that are poor conductors of heat will minimize heat loss. Glass is one of these. Fiberglass insulation uses spun glass for its insulating effect.

Plastic is also a poor conductor of heat. Foam cups are made of plastic which has tiny air bubbles suspended in it. Air is among the poorest conductors of heat. It turns out that a vacuum, or the complete lack of air, is the best insulator of all. This is the principle employed in the Thermos design.

The other important consideration in creating your container is its cost. Minimal design uses the fewest resources while maintaining the safety and efficacy of your product. Engineers almost never have the luxury of designing products or systems where cost is not a factor. Given unlimited resources, you could most likely come up with a container that would maintain the egg's temperature almost indefinitely, but no one could afford to buy it from you. Balancing cost and effectiveness into your plans is a critical skill you will need later.

3 YOUR ASSIGNMENT

Team Lab Report

Note: Since this lab is a competition, you will be writing a team lab report rather than an individual one. See the Team Authoring Strategies page in the Technical Communication of this online manual for guidance of how to do this.

Follow the lab report guidelines laid out in the page called Specifications for Writing Your Lab Reports in the Technical Communication section of this manual. As you write, the following discussion points should be addressed in the appropriate section of your lab report:

• Describe the rules of the competition in your introduction. What consequences did the rules have for your design decisions? Use the appropriate equations in your answer. You may do this in a numbered list, but please use full sentences.
• Explain equilibrium, heat, heat transfer and all the mechanisms that perform heat transfer. Discuss which of these mechanisms applied to your design.
• Define what thermal insulation is and the different types of Thermodynamic systems
• Discuss minimal design and its importance.
• Describe your container's design. Explain the choices you made. Make sure you include a discussion of the materials you chose and why. Talk about your team's strategy for winning the competition.
• What changes would have increased/decreased your MDR or IC?
• Should the temperature vs. time graph be smooth or should it have spikes? Explain how closely your curve approximates the ideal and what would affect the readings you recorded.
• Describe how your design succeeded or failed. Discuss design improvements.

Note: It is not unusual to experience instrumentation errors in this lab, leading to incorrect temperatures being recorded. Be sure to read How to Handle Unusual Data in the online manual to learn how to handle this.

Team PowerPoint Presentation

Follow the presentation guidelines laid out in the page called EG1004 Lab Presentation Format in the Introduction to Technical Presentations section of this manual. When you are preparing your presentation, consider the following points:

• What is the importance of minimal design?
• Why is it important in today's world to minimize heat loss?
• How would you improve your design?

4 MATERIALS AND EQUIPMENT

Materials with Price List

• Large foam cup - $0.50
• Lid - $0.25
• Paper cup - $0.40
• Styrofoam pieces - $0.05/6 pieces
• Tape - $0.10/ft
• Aluminum foil - $0.30/ft²
• Plastic wrap - $0.02/ft²

"NO RETURN" POLICY: When calculating cost, you must include ALL materials you request, even if you end up not using them. Make your selections carefully so you don't end up with cost that hurts your performance, but has no benefit.

Equipment Used

• Lab PC with DAQ Board and LabVIEW Program "Therm VI" Installed

Remember: You are required to take notes. Experimental details are easily forgotten unless written down. EG Standard Note Paper can be downloaded and printed from the EG website the EG1004 Web site. Use your lab notes to write the Procedure section of your lab report. At the end of each lab your TA will scan your lab notes and upload them to the EG1004 course section on MyPoly. You must attach your lab notes at the end of your lab report (use the "Insert Object" command in MS Word after your Conclusion). Keeping careful notes is an essential component of all scientific practice.

5 COMPETITION RULES

The following rules must be observed at all times during the competition. Violation of any of these rules will result in the disqualification.

• All materials must be inside the container.
• The container may not be larger than the largest cup provided.
• The egg may not be returned to the water.
• The container may not be held or covered during temperature readings.
• External heat sources are prohibited.
• The egg must be inside the container within 30 seconds from when you receive it.

6 PROCEDURE

Insulating Container Design

1. Analyze your materials and consider your design options, keeping in mind the lab's specifications. Make sure you take notes and make preliminary sketches during this process.
2. Now, sketch your design in pencil using the graph paper provided on the EG1004 Web site. Label your drawings clearly. Prepare a price-list for your insulating container based on the materials you have chosen. Have your TA sign the sketches and the price-list.
3. Build your insulating container based on the sketch you just completed. Your TA will provide the materials needed for your design. If you decide to modify your design during the construction of your insulating container, note the changes and describe the reasons for them. If the modifications required more materials to be used, make sure you update your price list and your TA approves it.
4. Ask your TA to take a picture of your container.

Competition

1. Before receiving your egg, make sure that the yellow wire of the thermocouple is connected to pin 3 on the DAQ board and the orange wire of the thermocouple to pin 4. Secure a length of cellophane tape, large enough to encircle the egg, to the other end of the thermocouple.

Note: The thermocouple wire must remain in constant contact with the egg throughout the 15-minute measurement period. Ensure that the thermocouple wire is attached securely.

2. The TA will bring the egg to you once you are ready to receive it. Attach the other end of the thermocouple to the egg using the tape you prepared. Be sure the ends of the tape overlap. Make sure the container is closed tightly.

Warning: Be careful! The egg is very hot.

3. Start the LabVIEW program (see Figure 2). Your TA will already have calibrated the Therm VI.

Warning: Make sure the program is set to Run. This will allow the thermal VI to record 30 temperature readings to an Excel spreadsheet. They will be your source data for performing necessary calculations.

Figure 2: Therm VI window

Data Analysis

1. Create two graphs using the X, Y Scatter template.

Excel 2003

Click on the icon that looks like a bar graph to start the Chart Wizard. For the first window, select the X, Y Scatter template.

Excel 2007

You'll find the template on the Insert tab, under the Charts group, with the Scatter icon. Click on the arrow below the icon and select the top left icon in the pulldown gallery. You can get the axes you want by clicking on the axis. You can get labels and titles by clicking on the chart, which will change the ribbon to the Design tab. In the Charts Layout group, click the icon that looks like the chart you want. Right click on the things you want to change.



2. For each of them, name the x-axis Time, and plot it in minutes with thirty second intervals. Name the y-axis Temperature. You may select the intervals based on your results. The first graph includes all fifteen minutes of testing. The second graph is just the last five minutes of testing. When you are finished, your graphs should look similar to Figures 3 and 4.



Figure 3: Temperature vs. Time diagram of 15 minute VI run



Figure 4: Temperature vs. Time diagram of Last 5 minutes of VI run

3. Calculate the Insulating Capacity (IC) of your design. IC is the value of the slope of the last five minutes of data.

Excel 2003

To do this, right click on any data point on your second graph and select Add Trendline, then Options. Check the box labeled Display equation on chart and click OK. Click on the equation and drag it to an area on your chart where it will be legible.




Excel 2007

Once again, click on the chart to get the Design tab on the ribbon. Under the Chart Layouts group, click on the chart template that has a trend line. As before, right click on the various items to make them what you want, including deleting things. Finally, right click on the trend line. This will bring up the Format Trendline window. On the left side, the Trendline Options item should be highlighted. If it isn't, click on it to highlight it. On the right side near the bottom is an item Display Equation on chart. Click on the check box to the left of this item and click Close. You can then click on the equation that's on the chart to move it where you want.



4. Print out the graphs and the table from LabVIEW and have your TA initial them. Have your TA write in your lab notes "Data/graph done. (signed) TA". This way only the lab notes have to be scanned in to complete the electronic lab report since the data/graph already exists in electronic form.
5. Calculate the Minimal Design Ratio (MDR) for your design:



IC is the insulating capacity you calculated earlier, cost is the cost of your container, T_R is the temperature of the room given to you by the TA, and T_F is the final temperature read by the thermocouple.

The team with the lowest MDR wins.

Your lab work is now complete. Please clean up your workstation. Return all unused materials to your TA. Refer to section 3 Your Assignment for the instructions you need to prepare your lab report.

Return to Table of Contents