Difference between revisions of "Sustainable Energy Vehicle Competition"

From EG1003 Lab Manual
Jump to: navigation, search
Line 18: Line 18:
  
 
=== Types of Renewable Energy ===
 
=== Types of Renewable Energy ===
Renewable energy are types of energy that can be harnessed from naturally replenished resources. Some examples of this includes sunlight, wind, and water. There are many benefits of using renewable energy such as clean energy sources, and they come from an abundant source that doesn’t become depleted. If we are able to efficiently utilize these renewable resources we can solve the problems with using non-renewable energy sources such as fossil fuels. [1]
+
Renewable energy is a type of energy that can be harnessed from naturally replenished resources. Some examples of this include sunlight, wind, and water. There are many benefits of using renewable energy such as clean energy sources, and they come from an abundant source that doesn’t become depleted. If we are able to efficiently utilize these renewable resources we can solve the problems with using non-renewable energy sources such as fossil fuels. [1]
  
 
==== Solar Power ====
 
==== Solar Power ====
Sunlight, like any other type of electromagnetic radiation, contains energy. Typically when the sunlight hits an object, the energy that it contains is converted into heat. However, certain materials can convert the energy into electrical current, and in this form we can harness it and store it as energy.  
+
Sunlight, like any other type of electromagnetic radiation, contains energy. Typically when the sunlight hits an object, the energy that it contains is converted into heat. However, certain materials can convert the energy into an electrical current, and we can harness it in this form and store it as energy.  
  
In a crystal structure, the materials used for solar panels contain covalent bonds where electrons are shared by the atoms within the crystal. When the light is absorbed, electrons within the crystal become excited and move to a higher energy level. When this occurs the electron has more freedom of motion within the crystal. When the electrons move around the crystal structure an electrical current is generated, this in turn gives us electrical energy. The reaction that occurs when sunlight shines onto a solar panel is shown in Figure 5. [2]
+
In a crystal structure, the materials used for solar panels contain covalent bonds where electrons are shared by the atoms within the crystal. When the light is absorbed, electrons within the crystal become excited and move to a higher energy level. When this occurs the electron has more freedom of movement within the crystal. When the electrons move around the crystal structure an electrical current is generated, this in turn gives us electrical energy. The reaction that occurs when sunlight shines onto a solar panel is shown in Figure 5. [2]
  
  
Older solar panels consist of large crystalline structures made from silicon. When sunlight hits the silicon on the solar panel, the photons from the sunlight energize the electrons in the material. These energized electrons create a higher electrical potential in the material, which is measured as a voltage between that material and ground. The silicon solar panels convert a large amount of the sunlight into electrical energy but are not cost due to high manufacturing costs.[2]
+
Older solar panels consist of large crystalline structures made from silicon. When sunlight hits the silicon on the solar panel, the photons from the sunlight energize the electrons in the material. These energized electrons create a higher electrical potential in the material, which is measured as a voltage between that material and ground.  
  
 
The material ''Copper indium gallium (di)selenide'' (CIGS) is also used in the production of solar panels. Panels made from CIGS have a smaller crystalline structure and are less expensive than their silicon counterparts. CIGS panels are relatively flexible and can easily be shaped into flexible films. The use of CIGS to make solar panels is referred to as thin-film solar technology because of its flexible nature. CIGS panels are in fact not as good at converting absorbed light into electrical current compared to silicon. However, for mass production purposes, CIGS solar panels are the more cost effective approach to produce solar panels for frequent use. [2]
 
The material ''Copper indium gallium (di)selenide'' (CIGS) is also used in the production of solar panels. Panels made from CIGS have a smaller crystalline structure and are less expensive than their silicon counterparts. CIGS panels are relatively flexible and can easily be shaped into flexible films. The use of CIGS to make solar panels is referred to as thin-film solar technology because of its flexible nature. CIGS panels are in fact not as good at converting absorbed light into electrical current compared to silicon. However, for mass production purposes, CIGS solar panels are the more cost effective approach to produce solar panels for frequent use. [2]
Line 35: Line 35:
 
==== Wind Energy ====
 
==== Wind Energy ====
  
Wind turbines are used to capture the wind’s energy and convert it into electrical energy. The structure of a wind turbine has a heavy influence on its functionality. The blades on wind turbines are slanted so that as the wind passes over the blades it creates an uneven pressure on each side causing them to spin. The spinning blades in turn drive a low speed shaft connected to a gearbox. The gearbox within the wind turbine converts the low speed rotation to a high speed rotation through a high speed shaft. The high speed shaft is connected to a brake and then into an electrical generator where mechanical energy is converted to electrical energy. [3]
+
Wind turbines are used to capture the wind’s energy and convert it into electrical energy. The structure of a wind turbine has a heavy influence on its functionality. The blades on wind turbines are slanted so that as the wind passes over the blades it creates an uneven pressure on each side causing them to spin. The spinning blades, in turn, drive a low speed shaft connected to a gearbox. The gearbox within the wind turbine converts the low speed rotation to a high speed rotation through a high speed shaft. The high speed shaft is connected to a brake and then into an electrical generator where mechanical energy is converted to electrical energy. [3]
  
 
A very basic electrical generator is made up of permanent magnets on each side with a rectangular coil connected to a commutator, a rotary electrical switch. The two permanent magnets on each side create a magnetic field. As the rectangular coil spins mechanically, the magnetic field through the area of the coil changes creating an alternating current through the coil itself. The commutator switches the polarity of the coil just as the polarity of the alternating current changes creating a direct current. The current is then output from the wind turbine. [3]
 
A very basic electrical generator is made up of permanent magnets on each side with a rectangular coil connected to a commutator, a rotary electrical switch. The two permanent magnets on each side create a magnetic field. As the rectangular coil spins mechanically, the magnetic field through the area of the coil changes creating an alternating current through the coil itself. The commutator switches the polarity of the coil just as the polarity of the alternating current changes creating a direct current. The current is then output from the wind turbine. [3]
Line 58: Line 58:
 
[[Image:Lab_renewener_05.png|center|thumb|500px|Figure 7b: Battery]]<br style="clear: both;" /></div></div><br style="clear: both;" />
 
[[Image:Lab_renewener_05.png|center|thumb|500px|Figure 7b: Battery]]<br style="clear: both;" /></div></div><br style="clear: both;" />
  
A '''diode''' is a device that allows current to pass through it in only one direction. This means that it has polarity, and will only allow current to pass from its positive side to its negative side. A '''Light Emitting Diode (LED)''' not only passes current, but also lights up when it's passing current. LEDs have a forward voltage and a reverse voltage. In the forward direction, the forward voltage and resistance are low and determined by the material used in the LED. The reverse voltage has a much higher resistance and a higher reverse voltage that prevents the flow of electrical current. The characteristic of the diode is to have low resistance to electrical flow in the forward direction and high residence in the reverse direction provides the ability to control the flow of electricity in one direction only.
+
A '''diode''' is a device that allows current to pass through it in only one direction. This means that it has polarity, and will only allow current to pass from its positive side to its negative side. A '''Light Emitting Diode (LED)''' not only passes current but also lights up when it's passing current. LEDs have a forward voltage and a reverse voltage. In the forward direction, the forward voltage and resistance are low and determined by the material used in the LED. The reverse voltage has a much higher resistance and a higher reverse voltage that prevents the flow of electrical current. The characteristic of the diode is to have low resistance to electrical flow in the forward direction and high residence in the reverse direction provides the ability to control the flow of electricity in one direction only.
  
 
There is a threshold voltage in the forward direction for the LED to emit light. Below the threshold voltage, there is no light. At and above the threshold voltage the LED emits light with intensity roughly linear with forward voltage. The symbol for the LED is shown in Figure 8.
 
There is a threshold voltage in the forward direction for the LED to emit light. Below the threshold voltage, there is no light. At and above the threshold voltage the LED emits light with intensity roughly linear with forward voltage. The symbol for the LED is shown in Figure 8.
Line 143: Line 143:
 
# Your design must be able to hold the power storage device on top of it during the trials (you may modify your design to fit the power storage device as you deem fit). Prepare a cost list for your renewable energy powered vehicle based on the setups and materials you have chosen. Have your TA '''sign''' the sketches and the cost list.  
 
# Your design must be able to hold the power storage device on top of it during the trials (you may modify your design to fit the power storage device as you deem fit). Prepare a cost list for your renewable energy powered vehicle based on the setups and materials you have chosen. Have your TA '''sign''' the sketches and the cost list.  
 
# Your TA will provide the materials needed for your design. If you decide to modify your design during the construction of your car, note the changes and describe the reasons for them. If the modifications required more materials to be used, make sure you update your cost list and that your TA approves it. (Note: You may modify your design between trials)
 
# Your TA will provide the materials needed for your design. If you decide to modify your design during the construction of your car, note the changes and describe the reasons for them. If the modifications required more materials to be used, make sure you update your cost list and that your TA approves it. (Note: You may modify your design between trials)
'''Before entering the competition, test if both your motor and cable are working, and that the motors turns in the desired direction of travel.'''
+
'''Before entering the competition, test if both your motor and cable are working, and that the motors turn in the desired direction of travel.'''
  
 
==== Competition ====
 
==== Competition ====

Revision as of 19:30, 30 October 2019

Objective

The experimental objective is to evaluate different sources of renewable energy. Design a sustainable energy vehicle using the power sources and power storage device provided in the lab to compete in a competition within the section.

Overview

Energy Storage

Capacitors

A capacitor is an electrical device used to store charge temporarily. Some capacitors can be used in place of a battery but they operate very differently from one. A capacitor is charged by a voltage source logarithmically, as shown in Figure 3.

Figure 3: Capacitor Charging Curve


Because of their design, these capacitors are sensitive to the polarity of the voltage applied to them. The capacitors used in this lab must be connected with the proper polarity, or they will fail. Therefore, be sure to check the capacitor used to make sure you have the negative sign on the capacitor connected to the negative applied voltage. Failure to do this will cause the capacitors to fail.

Figure 4: Polarized laboratory capacitor


The total energy a capacitor holds is given by the equation E = CV2 / 2. Note that the energy that the capacitor holds is proportional to the square of the voltage.

Types of Renewable Energy

Renewable energy is a type of energy that can be harnessed from naturally replenished resources. Some examples of this include sunlight, wind, and water. There are many benefits of using renewable energy such as clean energy sources, and they come from an abundant source that doesn’t become depleted. If we are able to efficiently utilize these renewable resources we can solve the problems with using non-renewable energy sources such as fossil fuels. [1]

Solar Power

Sunlight, like any other type of electromagnetic radiation, contains energy. Typically when the sunlight hits an object, the energy that it contains is converted into heat. However, certain materials can convert the energy into an electrical current, and we can harness it in this form and store it as energy.

In a crystal structure, the materials used for solar panels contain covalent bonds where electrons are shared by the atoms within the crystal. When the light is absorbed, electrons within the crystal become excited and move to a higher energy level. When this occurs the electron has more freedom of movement within the crystal. When the electrons move around the crystal structure an electrical current is generated, this in turn gives us electrical energy. The reaction that occurs when sunlight shines onto a solar panel is shown in Figure 5. [2]


Older solar panels consist of large crystalline structures made from silicon. When sunlight hits the silicon on the solar panel, the photons from the sunlight energize the electrons in the material. These energized electrons create a higher electrical potential in the material, which is measured as a voltage between that material and ground.

The material Copper indium gallium (di)selenide (CIGS) is also used in the production of solar panels. Panels made from CIGS have a smaller crystalline structure and are less expensive than their silicon counterparts. CIGS panels are relatively flexible and can easily be shaped into flexible films. The use of CIGS to make solar panels is referred to as thin-film solar technology because of its flexible nature. CIGS panels are in fact not as good at converting absorbed light into electrical current compared to silicon. However, for mass production purposes, CIGS solar panels are the more cost effective approach to produce solar panels for frequent use. [2]


Figure 5: A solar panel made using silicon is shown to have a change of electron flow as photons are being absorbed by the plate.


Wind Energy

Wind turbines are used to capture the wind’s energy and convert it into electrical energy. The structure of a wind turbine has a heavy influence on its functionality. The blades on wind turbines are slanted so that as the wind passes over the blades it creates an uneven pressure on each side causing them to spin. The spinning blades, in turn, drive a low speed shaft connected to a gearbox. The gearbox within the wind turbine converts the low speed rotation to a high speed rotation through a high speed shaft. The high speed shaft is connected to a brake and then into an electrical generator where mechanical energy is converted to electrical energy. [3]

A very basic electrical generator is made up of permanent magnets on each side with a rectangular coil connected to a commutator, a rotary electrical switch. The two permanent magnets on each side create a magnetic field. As the rectangular coil spins mechanically, the magnetic field through the area of the coil changes creating an alternating current through the coil itself. The commutator switches the polarity of the coil just as the polarity of the alternating current changes creating a direct current. The current is then output from the wind turbine. [3]


Figure 6: The internal structure of an electrical generator [3]



Hydroelectric Power

Water is constantly moved around in various states through the water cycle. Water evaporating from Earth’s surface condenses into clouds. The water in clouds over land will eventually precipitate in the form of rain effectively transporting water to a higher elevation and thus potential energy state. The energy is then release in the form of water flowing downstream. This movement provides opportunities to harness a seemingly infinite source of kinetic energy. In order to generate sufficient electricity from the motion of the water, it has to move fast enough and in large enough volumes to spin a turbine. The turbines used for hydroelectric energy operate in an almost identical manner to the turbines for used for wind power. The only differences occur in the physical construction of the turbine itself. In order to increase the volumes and motion of the water dams are created to store reservoirs of water.

Gravity causes the water held at the top of the dam to drop through the penstock (regulates water flow). At the end of the penstock is the turbine, which rotates thus creating the mechanical energy used to rotate the magnets in the generator.


Figure 7: The hydroelectric process of a dam

Electrical Components

In electrical engineering different electrical components are represented by different symbols. Below in Figures 7a and 7b are examples of symbols for a cell and a battery.

Figure 7a: Cell

Figure 7b: Battery


A diode is a device that allows current to pass through it in only one direction. This means that it has polarity, and will only allow current to pass from its positive side to its negative side. A Light Emitting Diode (LED) not only passes current but also lights up when it's passing current. LEDs have a forward voltage and a reverse voltage. In the forward direction, the forward voltage and resistance are low and determined by the material used in the LED. The reverse voltage has a much higher resistance and a higher reverse voltage that prevents the flow of electrical current. The characteristic of the diode is to have low resistance to electrical flow in the forward direction and high residence in the reverse direction provides the ability to control the flow of electricity in one direction only.

There is a threshold voltage in the forward direction for the LED to emit light. Below the threshold voltage, there is no light. At and above the threshold voltage the LED emits light with intensity roughly linear with forward voltage. The symbol for the LED is shown in Figure 8.

Figure 8: LED Symbol3

Different arrangements of electrical components allow engineers to design different devices. Components like resistors, inductors, and capacitors can be arranged in two different ways. In a series circuit, the element's conductors are connected end to end. The current in a series circuit remains the same in all the electrical elements. In a series circuit, as shown in Figure 9, the sum of the voltages across each element is equal to the voltage of the power source (Vout = VA + VB + VC).

Figure 9: A series circuit


In a parallel circuit, as shown in Figure 10, the element's conductors are connected at opposing ends. The current that is supplied by the voltage source equals the current that flows though elements D and E. The voltage across the elements that are parallel is the same (Vout = VD = VE).

Figure 10: A parallel circuit


The motor provided is a 9V motor that will operate with voltages lower than 9V with reduced torque and speed. A motor with no load draws 9mA; a stalled motor draws well over 350mA. By increasing the voltage provided to the motor you can increase the motor speed. By increasing current you increase the torque.

Design Considerations

  • Which source yields the most voltage per unit cost?
  • Which circuit configuration will provide the most desirable voltage across the load? Parallel or series?
  • Which aspects of the competition formula are most advantageous?

Materials and Equipment

Materials with Price List

  • Horizon wind-turbine: $7.50 each
  • Water turbine: $5.00 each
  • Solar battery panels: $10.00 each
  • 1 Farad 5.5V capacitor: $3.00 each
  • Alligator cable sets: $0.50/pair
  • Standard Lego car chassis plus Lego parts kit: $0, limit one per group
  • Lego to alligator cable clip connector: $0.10 each
  • Duct Tape: $0.10/feet

Equipment Used

  • Horizon Wind-Turbine
  • Sunforce 50013 1-Watt Solar Battery Charger
  • Adjustable Table fan
  • Heat Lamp
  • DMM (Digital Multi-meter)
  • Music Voltmeter
  • 2V DC Motor
  • 1 Farad 5.5V Capacitor
  • 3 Alligator cable sets
  • Standard Lego Car Chassis plus Lego parts kit
  • Lego to Alligator Cable Clip Connector
  • Scissors
  • Tape

Procedure

Every group will be designated to test the power storage device and a single power source.

Part 1: Testing the Power Storage Device

Charging a Capacitor

  1. Connect an alligator clip to each of the cables coming out of the 3V power supply. (red is positive and black is negative)
  2. Connect to the one of unconnected alligator clips the ammeter (multimeter setting measuring current)
  3. Connect the rest of the unconnected cables (one from ammeter and one alligator clip) connect to pins of the capacitor with correspond polarity. (refer to Figure 10)
  4. Charge until the current is zero.
  5. Discharge the charged capacitor by connecting it to the music voltmeter provided.
Figure 17: This is circuitry for charging a capacitor.


Part 2: Testing the Power Sources

Each team will analyze one type of renewable power source, determined by the TA. Both voltage and current must be measured and recorded, and power must be calculated.

Wind turbine

  1. Connect the wind turbine to the music voltmeter using the alligator clips provided. Measure the voltage and current across the music voltmeter using the digital multimeter provided. The connections for measuring voltage and current across the music voltmeter are shown in Figures 9 & 10.
  2. Adjust the position of the turbine to find the maximum voltage and current that can be generated.
  3. Calculate and record the power generated by the turbine and give information to TA.

Solar Panel

  1. Connect the solar panel to the music voltmeter using the alligator clips provided. Place the solar panel near the heat lamp and measure the voltage and current across the music voltmeter using the digital multimeter provided.
  2. Adjust the position of the solar panel to find the maximum voltage and current that can be generated.
  3. Calculate and record the power generated by the solar panel and give information to the TA.
    Caution! The heat lamps and solar panels may become extremely hot when used for a long duration of time. Do not touch them immediately after use and turn them off when not in use.

Hydroelectric Turbine

  1. Connect the red wire of the water wheel to the positive (red) end of the multimeter and the black wire to the negative (black) end of the multimeter. Set the multimeter to measure voltage.
  2. Notify the TA once the connections have been set up. The TA will then take you to the AUV room's sink to measure the voltage and (electrical) current produced by the water coming from the sink. Be very careful to keep water off of the multimeters.
  3. Calculate and record the power generated by the water wheel and give information to the TA.


Part 3: Renewable Car Competition

  1. Assess your materials and consider the data established from Part 1 and Part 2. Choose materials for your car design, keeping in mind the Competition Ratio. Make sure you make preliminary sketches during this process.
  2. Your design must be able to hold the power storage device on top of it during the trials (you may modify your design to fit the power storage device as you deem fit). Prepare a cost list for your renewable energy powered vehicle based on the setups and materials you have chosen. Have your TA sign the sketches and the cost list.
  3. Your TA will provide the materials needed for your design. If you decide to modify your design during the construction of your car, note the changes and describe the reasons for them. If the modifications required more materials to be used, make sure you update your cost list and that your TA approves it. (Note: You may modify your design between trials)

Before entering the competition, test if both your motor and cable are working, and that the motors turn in the desired direction of travel.

Competition

The renewable energy vehicle must be able to carry the power storage device you choose to use on it (e.g. capacitor). You may only power your capacitor using the power sources provided. Violations to these rules will result in a failing grade for the lab report for this lab.

When requested by the TA, the student will position the renewable energy car and complete the necessary connections before the trial begins.

The competition will be won by the team that has the highest competition ratio:

The TA will record the test data after five minutes or when the car stops moving, whichever occurs first. The TA will then calculate the competition ratio. The tabulation for the whole class will be provided.

Assignment

Team Lab Report

Note: You will be writing a team lab report rather than an individual one. See the Team Authoring Strategies page in the Technical Communication of this online manual for guidance of how to do this.

Follow the lab report guidelines laid out in the page called Specifications for Writing Your Lab Reports in the Technical Communication section of this manual. As you write, the following discussion points should be addressed in the appropriate section of your lab report:

  • Describe the rules of the competition in your introduction. What consequences did the rules have for your design decisions? Use the appropriate equations in your answer.
  • Explain how solar panels and wind turbines work.
  • Explain the concept of the capacitor.
  • Discuss the advantages and disadvantages of the solar panel, wind-turbine, and hydroelectric generator.
  • Describe your renewable energy vehicle design and explain the choices you made in your design.
  • Discuss the possible power sources and their effectiveness. How did the voltage measurements of the power sources impact your design?
  • Discuss minimal design. Did you use all the materials you purchased? Describe the importance of minimal design and explain how you employed it in your design. (how did you minimize your cost)
  • Describe how your design succeeded or failed. What choices could you have made to improve your final standing in the competition?
  • Discuss how you would improve the competition ratio, how was your design compared to the other group’s designs.
  • Describe the power source chosen for the design.
  • Include spreadsheet with every team's results. Describe the results and talk about other designs in the class.

Remember: Lab notes must be taken. Experimental details are easily forgotten unless written down. EG1003 Lab Notes Paper can be downloaded and printed from the EG1003 Website. Use the lab notes to write the Procedure section of the lab report. At the end of each lab, a TA will scan the lab notes and upload them to the Lab Documents section of the EG1003 Website. One point of extra credit is awarded if the lab notes are attached at the end of the lab report. Keeping careful notes is an essential component of all scientific practice.

Team PowerPoint Presentation

Follow the presentation guidelines laid out in the EG1003 Lab Presentation Format section of this manual. When you are preparing your presentation, consider the following points:

  • Since one term in the competition ratio is cost, present the cost of your vehicle. Use the page How to Show Cost Data in Presentations for instructions on how to do this
  • How would you improve your renewable energy powered car?

References

[1] NextEra Energy Resources, LLC., . "Benefits of Renewable Energy." NextEra Energy Resources. NextEra Energy Resources, 2012. Web. 24 Jul 2012. <http://www.nexteraenergyresources.com/content/environment/benefits.shtml>.

[2] Locke, S.. "How does solar power work." Scientific american. Scientific American, 2008. Web. 24 Jul 2012. <http://www.scientificamerican.com/article.cfm?id=how-does-solar-power-work>.

[3] Layton, J.. "How Wind Power Works." How stuff works. Discovery, 2011. Web. 24 Jul 2012. <http://science.howstuffworks.com/environmental/green-science/wind-power.htm>.

[4] Reg Tyler, . "Types of Fuel Cells." Energy efficeny and renewable energy. U.S. Department of Energy, 2011. Web. 24 Jul 2012. <http://www1.eere.energy.gov/hydrogenandfuelcells/fuelcells/fc_types.html>.

[5] Perlman, Howard.. "Hydroelectric power: How it works." U.S. Geological Survey, 2016. Web 4 Jan 2018. <https://water.usgs.gov/edu/hyhowworks.html>.