Difference between revisions of "Sustainable Energy Applications (Virtual)"

From EG1004 Lab Manual
Jump to: navigation, search
(1003 --> 1004)
 
(16 intermediate revisions by one other user not shown)
Line 99: Line 99:
In (4), P is the power in Watts, I is the current in Amperes, and V is the voltage in Volts.
In (4), P is the power in Watts, I is the current in Amperes, and V is the voltage in Volts.


<!--The <b>motor</b> provided in the lab is a 9V VEX motor that will operate with voltages lower than 9V with reduced torque and speed (Figure 10). A motor with no load draws 9 mA, and a stalled motor draws well over 350 mA. Increasing the voltage provided to the motor increases the speed. Increasing the current increases torque.
The <b>motor</b> provided in the lab is a 9V VEX motor that will operate with voltages lower than 9V with reduced torque and speed (Figure 10). A motor with no load draws 9 mA, and a stalled motor draws well over 350 mA. Increasing the voltage provided to the motor increases the speed. Increasing the current increases torque.


[[Image:Vex_motors.png|thumb|200px|center|Figure 10: 9V VEX Motor]]-->
[[Image:Vex_motors.png|thumb|200px|center|Figure 10: 9V VEX Motor]]
<!--
=== VEX Robotics ===
=== VEX Robotics ===
Vex Robotics is used globally for students to understand the fundamentals of robotics. It is commonly used to model the capabilities of vehicles.
Vex Robotics is used globally for students to understand the fundamentals of robotics. It is commonly used to model the capabilities of vehicles.
Line 108: Line 109:


[[Image:Vex_image.png|thumb|200px|center|Figure 10: 9V VEX Motor]]
[[Image:Vex_image.png|thumb|200px|center|Figure 10: 9V VEX Motor]]
-->


== Design Considerations ==
== Design Considerations ==
Line 132: Line 134:
|}-->
|}-->


* Computer with downloaded software
* TinkerCad


= Procedure =
= Procedure =


The power storage device and power sources will be tested individually. The results of the tests will be used in determining the best power source in designing the sustainable energy vehicle.
This lab is divided into 3 sections: the testing of the power storage device, the investigation of renewable energy sources, and the data analysis of the United States’ renewable energy consumption. The power storage device and power sources will be tested individually. The results of the tests will be used in determining the best power source in designing the sustainable energy vehicle.


== 1. Starting a New Circuit in Tinkercad ==
<b>In order to create new circuits or copy an existing template of a circuit in Tinkercad, follow the steps below:</b>


# Tinkercad is an online 3D modeling program and will be used in this lab to simulate the circuits.
# Go to tinkercad.com and sign in with an Autodesk account.
# Go to tinkercad.com and sign in with an Autodesk account.
# To start a new circuit, on the left side of the home screen select Circuit > Create new circuit.  
# To start a new circuit, on the left side of the home screen select Circuit > Create new circuit.  
Line 147: Line 148:
## Select the Copy & Tinker option. This will copy the template to the workspace so it can be edited.
## Select the Copy & Tinker option. This will copy the template to the workspace so it can be edited.


== 2. Testing Series and Parallel Circuits in Tinkercad ==
== 1. Testing the Power Storage Device ==
Explore a series and parallel circuit in Tinkercad.
 
# Copy this [https://www.tinkercad.com/things/3BVjpi5FZMV template] to the Tinkercad workspace using the steps in Starting a New Circuit in Tinkercad.
# Click and drag a multimeter on the workspace.
# Click on it to get the multimeter dialogue box. To measure current go to the Multimeter dialogue box > Mode > Amperage. To measure voltage go to the Multimeter dialogue box > Mode > Voltage.
# Based on the guidelines, add a multimeter to both the series circuit and the parallel circuit.
## Measure the voltage across both circuits. Make sure that the multimeter is wired in parallel to measure the voltage.
## Measure the current across both circuits. Make sure that the multimeter is wired in series to measure the current.
# Record and compare the two measurements for the series circuit and the parallel circuit.
 
== 3. Testing the Power Storage Device ==


=== Charging a Capacitor ===
=== Charging a Capacitor ===
Line 167: Line 157:
# Wire the negative end of the 9V battery to the negative end of the multimeter. To wire these two components, simply click on the negative terminal of the battery, and click once again on the negative terminal of the multimeter. <b><font color=#ff0000>Red</font></b> is the positive terminal and <b>black</b> is the negative terminal.
# Wire the negative end of the 9V battery to the negative end of the multimeter. To wire these two components, simply click on the negative terminal of the battery, and click once again on the negative terminal of the multimeter. <b><font color=#ff0000>Red</font></b> is the positive terminal and <b>black</b> is the negative terminal.
# Similarly, wire the positive end of the multimeter to terminal 1 on the capacitor. Wire terminal 2 on the capacitor to the positive terminal of the battery.
# Similarly, wire the positive end of the multimeter to terminal 1 on the capacitor. Wire terminal 2 on the capacitor to the positive terminal of the battery.
# Click the “A” on the multimeter to measure ampere.
# To charge the capacitor click Start Simulation. Charge the capacitor until the current in the circuit is zero ampere (0A).
# To charge the capacitor click Start Simulation. Charge the capacitor until the current in the circuit is zero ampere (0A).
# Click on Stop Simulation once the multimeter reading is zero ampere (0A).
# Click on Stop Simulation once the multimeter reading is zero ampere (0A).
Line 173: Line 164:
[[Image:Image.png|thumb|500px|center|Figure 11: Tinkercad Circuit to Charge a Capacitor]]
[[Image:Image.png|thumb|500px|center|Figure 11: Tinkercad Circuit to Charge a Capacitor]]


== 4. Testing the Power Sources ==
== 2. Testing the Power Sources ==


The physical wiring, voltage data, and current data for the wind turbine and the solar panel is given.   <b>You are responsible for building a circuit for and analyzing both the lemon and potato battery via tinkerCAD.</b> All voltage and current must be measured and recorded, and power must be calculated.
The physical wiring, voltage data, and current data for the wind turbine and the solar panel is given. <b>Calculate the power for each power source.</b>  


{| class="wikitable"
{| class="wikitable"
Line 186: Line 177:
|}  
|}  
   
   
=== Lemon Battery ===
Batteries are not the same as capacitors. Batteries are used instead of capacitors because TinkerCAD does not allow for the capacitors to be charged at the beginning of a simulation.


# Click and drag two lemon batteries and a multimeter on the interface. If the lemon battery is not visible in the components menu on the right, click on Components > All.
=== Single Battery in Series with Multimeter ===
# Create a circuit using two lemon batteries. Wire the multimeter to be in series with the circuit.
#Click and drag one 3V battery, a DC motor, and a multimeter on the interface.
# Click on Start Simulation and record the final current produced by the circuit in series.
#Wire the one 3V battery, the DC motor, and the multimeter in <b>series</b>.
# Create a circuit using two lemon batteries. Wire a multimeter in parallel to the circuit. In order to create the circuit, diodes are required to connect more than two wires.
##Refer to Figure 6 for how to wire a series circuit.
# Click on Start Simulation and record the final voltage produced by the circuit in parallel.
#Click on Start Simulation and record the final current produced by the circuit in series.
# Make sure to wire the positive terminal of the lemon battery with the positive terminal of the multimeter and the negative terminal of the lemon battery to the negative terminal of the multimeter.
#Take a screenshot of the circuit with the current reading.
# Take a screenshot of both the circuits with the voltage and current reading.


=== Potato Battery ===
=== Batteries in Series ===  
#Click and drag two 3V batteries, a DC motor, and a multimeter on the interface.
#Wire the two 3V batteries, the DC motor, and the multimeter in <b>series</b>.
#Click on Start Simulation and record the final current produced by the circuit in series.
#Repeat steps 1-3 but with a reversed polarity for one of the batteries. To do this, flip one of the batteries so that it is wired backwards.
#Take a screenshot of both circuits with the current reading.


# Click and drag two potato batteries and a multimeter on the interface. If the potato battery is not visible in the components menu on the right, click on Components > All.
=== Batteries in Parallel ===
# Create a circuit using two potato batteries. Wire the multimeter to be in series with the circuit.
#Click and drag two 3V batteries, a DC motor, and a multimeter on the interface.
# Click on Start Simulation and record the final current produced by the circuit in series.
#Wire DC motor and multimeter in series and the two 3V batteries in <b>parallel</b>.
# Create a circuit using two potato batteries. Wire a multimeter in parallel to the circuit. In order to create the circuit, diodes are required in order to connect more than two wires.
##Refer to Figure 6 for how to wire a series circuit
# Click on Start Simulation and record the final voltage produced by the circuit in parallel.
#Click on Start Simulation and record the final current produced by the circuit in parallel.
# Make sure to wire the positive terminal of the potato battery with the positive terminal of the multimeter and the negative terminal of the potato battery to the negative terminal of the multimeter.
#Repeat steps 1-3 but with a reversed polarity for one of the batteries. To do this, flip one of the batteries so that it is wired backwards.
# Take a screenshot of both the circuits with the voltage and current reading.
#Take a screenshot of both circuits with the current reading.


=== Data Analysis ===  
=== Data Analysis ===  


# Review the circuit, voltage, and current of the solar panel and wind turbine power source. Calculate the power of the solar panel, wind turbine, lemon battery, and potato battery.
#Share and explain the circuits built and the data collected for the wind turbine, solar panel, batteries in parallel, and batteries in series to your group.
# Based on the calculated power of each renewable energy source, determine the best power source in order to theoretically power a sustainable energy vehicle.
#Based on the calculated power of each renewable energy source and the results of the analysis of the circuits in series and parallel, determine the best power source and circuit design in order to theoretically power a sustainable energy vehicle with two capacitors.
#Sketch the circuit design in your notes and include the polarity on the capacitors and power sources.


== 5. Sustainable Energy Vehicle ==
== 3. Case Study: Historical Energy Statistics  ==


In this part, a simple vehicle will be designed and assembled in Fusion 360. This vehicle will utilize one motor that is powered by the capacitors in the previous steps.  
In this part, a thorough investigation on the historical trends of renewable energy consumption in the United States will be conducted based on statistical data from the U.S. Energy Information Administration (EIA). In accordance with the data, four graphs will be constructed: a line graph showing the yearly trend for hydroelectric power, geothermal power, solar power, wind power, and biomass power, and a pie chart representing the 2019 distribution in renewable energy. These graphs will then be appended with data regarding fossil fuel energy consumption.  


=== Importing VEX Robotics Parts ===
=== Modeling the Yearly Trend ===


# The VEX parts for the vehicle can be found in a ZIP folder [[Media:Sustainable_Energy_Vehicle.zip|here]]. The latest version of Fusion 360 must be downloaded for the parts to appear properly.
#Download the [[Media: Lab_10_-_Sustainable_Energy_Applications_Raw_Data.xlsx| Excel file]] containing the raw data for the yearly energy consumption of various renewable energy sources from 1949 to 2019
# Unzip the parts to a space on the computer.
#The line graph will contain multiple lines that represent the different renewable energy sources. The procedure to graph the renewable energy consumption for hydroelectric power is provided. <b>Complete a similar procedure for the remaining renewable energy sources.</b>
# In Fusion 360, open the Data Panel (icon with 9 boxes at the top left) and click Upload (Figure 12). Select the unzipped part files to upload them to Fusion 360’s cloud memory. Fusion 360 can only import files uploaded to its cloud.
##On the Excel ribbon, click on the Insert tab, and click “Scatter with Straight Line” on the Scatter option under the Charts group. This should create a blank line graph, as shown in Figure 12.
 
##;[[Image:Lab10_excel_ribbion.png|500px|thumb|center|Figure 12: Inserting a Line Graph]]
[[Image:Data_panel.png|thumb|500px|center|Figure 12: Data Panel]]
##Right-click on the empty graph and choose the “Select Data” option. A new window will appear where the graphed data can be inputted.  
 
##Under the “Legends Entries (Series)” tab, click on the “Add” option, as shown in Figure 13. A new window called “Edit Series” will appear.
=== Design the Vehicle ===
##;[[Image:Lab10_excel_dataSource.png|500px|thumb|center|Figure 13: Utilizing the “Select Data Source” Window ]]
##In the “Series name” textbox, type in the name of the power source. In this case, type in Hydroelectric Power.  
##In the “Series X values” textbox, highlight the years in column A from 1949 to 2019.
##In the “Series Y values” textbox, highlight the total energy consumption from hydroelectric power in column B that corresponds to 1949 to 2019. The “Edit Series” should appear similar to Figure 14.
##;[[Image:Lab10_excel_editSeries.png|500px|thumb|center|Figure 14: Utilizing the “Edit Series” Window ]]
##Click “OK” to graph the Hydroelectric Power data.
#Next the data for the remaining renewable energy sources must be added to the same graph. To add the data, repeat steps 2b-g for each renewable energy source.
#Rename the axis and titles appropriately. Include a legend by checking off “Legend” in the dropdown menu at the top right of the graph.


Review the parts that are available. Consider the following restraints while designing your car:
=== Modeling the 2019 Distribution ===
* A maximum of two motors are allowed.
* The design must be able to hold the capacitors on top of it.
* Modify the design to have a location to store the power storage device.
* The motor must be connected to a minimum of two wheels.


<b>Do not worry about inserting nuts and bolts. Primarily focus on the general shape of the design with shafts, wheels, and the structural components.</b>
#To visualize the distribution of the various renewable energy sources in recent years, a pie chart will be created based on the 2019 year. This part will continue with the raw data obtained from the previous part.
#On the Excel ribbon, click on the Insert tab, and click “2-D Pie” on the Pie Chart option under the Charts group. This should create a blank line graph, as shown in Figure 15.
#;[[Image:Lab10_pieChart.png|500px|thumb|center|Figure 15: Inserting a Pie Chart]]
#Right-click on the empty graph and choose the “Select Data” option. A new window will appear where the graphed data can be inputted.  
#Under the “Legends Entries (Series)” tab, click on the “Add” option. A new window called “Edit Series” will appear.
#In the “Series Values” textbox, highlight each renewable energy sources’ total energy consumption for the 2019 year. Completing this would automatically create five labels under the “Horizontal (Category) Axis Labels” tab, as shown in figure 16.
#;[[Image:Lab10_horizontalAxisLabels.png|500px|thumb|center|Figure 16: Horizontal Axis Labels]]
#Select the row labeled “1” and click on the “Edit” option under “Horizontal (Category) Axis Labels” tab. In the “Axis-label range” textbox, select the names of each renewable energy source (B2:F2) and select OK.
#Rename the title appropriately.


=== Assemble the Parts ===
=== Fossil Fuel Energy Modeling ===
#Copy the data in the Fossil Fuel data sheet (located at the bottom left of the excel) to the main data sheet. Ensure that the data on the main sheet is not overwritten by the Fossil Fuel data.
#Following the same steps as the “Modeling the Yearly Trend” procedure and “Modeling the 2019 Distribution,” create a new scatter plot and a new pie chart representing both renewable energy sources and fossil fuel energy sources.
##<b>For the renewable energy sources scatter plot you should have 5 series</b>: Hydroelectric, Geothermal, Solar, Wind, & Biomass.
##<b>For the fossil fuel energy sources you should have 3 series</b>: Coal, Natural Gas, & Petroleum.
#;You should have a total of 8 series.


# Ensure that the Design workspace is open in Fusion 360. This is indicated at the top left.
At the end of this case study there should be <b>four graphs in total</b>:
# The VEX part files can be inserted into a new Fusion 360 file by simply dragging and dropping them from the Data Panel into the space. Alternatively, right click the components and select Insert into Current Design. Save the blank file before assembling the vehicle by going to File > Save as.
*a scatter plot containing the renewable energy sources
# Import the other parts based on the design that was sketched. Connect all the parts using the Align tool to complete the model. Use the tips from the Fusion 360 section in the Overview and watch the short tutorial on the Align Tool for instructions to properly connect the components of the vehicle in Fusion 360.
*a pie chart showing the 2019 distribution in renewable energy
# Take screenshots of the designed vehicle in Fusion 360 and send it to the lab TA.
*a scatter plot containing both renewable energy sources and fossil fuel energy sources
*a pie chart showing the 2019 distribution in renewable energy sources and fossil fuel energy sources


=== Extra Credit ===
=== Extra Credit ===
To receive extra credit, create two wires using the sweep tool that connects the capacitor to a motor. Use Google, online Fusion 360 forums, and Youtube tutorials to complete this. <b>To receive extra credit, the entire vehicle design with the sweeped wires must be completed before the end of lab and also must be included in the team presentation.</b>
To receive extra credit, predict the expected yearly energy consumption of wind power and solar power for 2030, 2040, and 2050 using Excel. Justify the methodology used to make this prediction.<b> To receive extra credit, this task must be completed with a reasonable justification before the end of the lab and also must be included in the team presentation.</b>  
 


<!--== 5. Sustainable Energy Vehicle Competition ==
<!--== 5. Sustainable Energy Vehicle Competition ==
Line 286: Line 300:
# Take screenshots of the designed vehicle and send it to the lab TA.
# Take screenshots of the designed vehicle and send it to the lab TA.


The Lab TAs have prepared an Excel file with the section's competition results. It can be accessed in the [http://eg.poly.edu/documents.php Lab Documents] section of the EG1003 website. This chart must be included in the PowerPoint presentation and in the Data/Observations section of the lab report. The lab work is now complete. Refer to the Assignment section for the instructions needed to prepare the lab report.-->
The Lab TAs have prepared an Excel file with the section's competition results. It can be accessed in the [http://eg.poly.edu/documents.php Lab Documents] section of the EG1004 website. This chart must be included in the PowerPoint presentation and in the Data/Observations section of the lab report. The lab work is now complete. Refer to the Assignment section for the instructions needed to prepare the lab report.-->


= Assignment =
= Assignment =
== Individual Lab Report ==
== Individual Lab Report ==
<!--<b>Note:</b> You will be writing a team lab report rather than an individual one. See the [[Team Authoring Strategies]] page in the <i>Technical Communication</i> of this online manual for guidance of how to do this.-->
<!--<b>Note:</b> You will be writing a team lab report rather than an individual one. See the [[Team Authoring Strategies]] page in the <i>Technical Communication</i> of this online manual for guidance of how to do this.
This lab report is <b>optional</b> and you will receive <b>extra credit</b> for submitting it. {{Labs:Lab Report}}
This lab report is <b>optional</b> and you will receive <b>extra credit</b> for submitting it.-->


* Define renewable energy
{{Labs:Lab Report}}
* Explain how solar panels and wind turbines work
* Explain the concept of the capacitor
* Discuss the advantages and disadvantages of all the energy sources
* Describe the renewable energy vehicle design and explain the choices made in the design
* Discuss the power sources and their power output. How did the voltage measurements of the power sources impact the design?
* Discuss whether one or two motors were used in design and why
* Specify the power source chosen for the design
* Discuss your design. Why did you choose the chassis or wheels? How did you factor in the constraints of the vehicle?
* Discuss how the design compared to the other designs
* Include screenshots of the lemon and potato battery circuits
* Discuss what part of the lab you completed for your group and why it was important to the overall experiment.


*Define renewable energy
*Explain how solar panels and wind turbines work
*Explain the concept of the capacitor
*Discuss the advantages and disadvantages of both energy sources
*Discuss the power sources and their power output. How did the voltage measurements of the power sources impact the power?
*Specify the power source chosen for the design
*Include the graphs for the renewable and nonrenewable energy trends
*Based on the yearly trend for renewable energy consumption, discuss the qualitative changes in renewable energy in the past twenty years. Briefly research why these changes occurred
*Based on both the yearly trend for renewable energy consumption and the 2019 distribution, what is the dominant source of renewable energy? Do you think it will remain the dominant source of renewable energy in the future?
*Compare the yearly renewable energy trends with the fossil fuel energy trends. Discuss the modern energy consumption profile
*Include screenshots of the batteries in parallel and batteries in series circuits.
*Discuss what part of the lab you completed for your group and why it was important to the overall experiment.


{{Labs:Lab Notes}}
{{Labs:Lab Notes}}
Line 313: Line 328:
{{Labs:Team Presentation}}
{{Labs:Team Presentation}}


* Discuss why you chose your renewable energy source
*Discuss why you chose your renewable energy source
* Discuss the power sources and their power output. How did the voltage measurements of the power sources impact the design?
*Discuss the power sources and their power output. How did the voltage measurements of the power sources impact the design?
* Discuss your design. Why did you choose the chassis or wheels? How did you factor in the constraints of the vehicle?
*Discuss why you chose to have the capacitors in series or parallel
* How would the renewable energy vehicle be improved?
*Discuss your renewable energy consumption graphs and the trends observed
*Discuss the overall energy consumption graphs and the trends observed


= References =
= References =

Latest revision as of 18:15, 22 August 2022

Objective

The experimental objective of this lab is to investigate and evaluate solar power and wind power as sources of renewable energy and use the results of that evaluation to theoretically power a sustainable energy vehicle. The second objective of this lab is to graphically compile and analyze the monthly energy consumption data from various renewable energy sources to understand the historical rising trend of renewable energy usage.

Overview

While humans have been using renewable energy sources, such as sails to power boats, windmills to pump water, or water-driven wheels to power machinery that mills grains, for millennia, the environmental impact of burning fossil fuels, such as oil, natural gas, and coal, has prompted greater interest in and greater investment in renewable energy sources, including solar power, wind power, and hydroelectric power. But some renewable energy sources cannot generate power consistently, notably solar power and wind power, so there is equal interest in developing energy storage devices that can operate at grid-scale or hold sufficient energy to power entire communities for an extended time after being charged by a renewable energy source.

Types of Renewable Energy

Renewable energy is a type of energy that can be harnessed from naturally replenished resources. Some examples of this are sunlight, wind, and water. There are many benefits of using renewable energy. They are clean energy sources, and they come from an abundant source that do not become depleted. If these renewable resources can be harnessed efficiently, they can solve the problems with using non-renewable energy sources, such as fossil fuels (NextEra Energy Resources, 2012).

Solar Power

Sunlight, like any other type of electromagnetic radiation, contains energy. Typically, when sunlight hits an object, the energy that it contains is converted into heat. Certain materials can convert the energy into an electrical current. In this form, it can be used as a power source and it can be stored as energy.

In a crystal structure, the materials used for solar panels contain covalent bonds where electrons are shared by the atoms within the crystal. When the light is absorbed, electrons within the crystal become excited and move to a higher energy level. When this occurs, the electron has more freedom of movement within the crystal. When the electrons move around the crystal structure an electrical current is generated. The reaction that occurs when sunlight hits a solar panel is shown in Figure 1 (Locke, 2008).

Figure 1: A Silicon Solar Panel Showing the Electron Flow

Older solar panels use large crystalline structures made from silicon. When sunlight hits the silicon on the solar panel, the photons from the sunlight energize the electrons in the material. These energized electrons create a higher electrical potential in the material that is measured as a voltage between that material and ground.

The material copper indium gallium (di)selenide (CIGS) is also used in the production of solar panels. Panels made from CIGS have a smaller crystalline structure and are less expensive than their silicon counterparts. CIGS panels are relatively flexible and can easily be shaped into flexible films. The use of CIGS to make solar panels is referred to as thin-film solar technology because of its flexible nature. CIGS panels are not as good at converting absorbed light into electrical current compared to silicon. But for mass production purposes, CIGS solar panels are the more cost effective approach to produce solar panels for frequent use (Locke, 2008).

Wind Energy

Wind turbines are used to capture the wind’s energy and convert it into electrical energy. The blades on wind turbines are slanted so that as the wind passes over the blades it creates an uneven pressure on each side, causing them to rotate. The spinning blades drive a low speed shaft connected to a gearbox. The gearbox within the wind turbine converts the low speed rotation to a high speed rotation through a high speed shaft. The high speed shaft is connected to a brake and then into an electrical generator where mechanical energy is converted to electrical energy (Layton, 2011).

A basic electrical generator is made of permanent magnets on each side with a rectangular coil connected to a commutator, which is a rotary electrical switch (Figure 2). The two permanent magnets on each side create a magnetic field. As the rectangular coil spins mechanically, the magnetic field through the area of the coil changes, creating an alternating current through the coil. The commutator switches the polarity of the coil just as the polarity of the alternating current changes, creating a direct current. The current is then output from the wind turbine (Layton, 2011).

Figure 2: The Internal Structure of an Electrical Generator (Layton, 2011)

Energy Storage

Capacitors have many uses in circuits and signal processing. In this lab, a capacitor can be used as the power source for the renewable energy vehicle. Fundamentally, a capacitor is an electrical device that is used to store charge temporarily. Some capacitors can be used in place of a battery, but they operate very differently from a battery. A capacitor is charged by a voltage source logarithmically, as shown in Figure 3.

Figure 3: Capacitor Charging Curve

Because of their design, these capacitors are sensitive to the polarity of the voltage applied to them. The capacitors used in this lab must be connected with the proper polarity. In the lab, the capacitor’s negative lead must be connected to the negative applied voltage (Figure 4). Failure to do this will cause the capacitor to fail.

Figure 4: Polarized Capacitor

The energy a capacitor holds is proportional to the square of the voltage across the capacitor (1).

(1)

In (1), E is the energy, C is the capacitance, and V is the voltage.

Electrical Components

The design of a circuit determines its behavior. In this lab, one circuit design will increase the speed output of a motor and the other will increase the torque output of a motor. In electrical engineering, different electrical components are represented by different symbols. Figures 5A, 5B, and 5C show the symbols for a battery, capacitor, and DC source, respectively. They are all forms of energy storage devices.

Figure 5A: Symbol for Battery
Figure 5B: Symbol for Capacitor
Figure 5C: Symbol for DC Source

Different arrangements of electrical components allow engineers to design different devices. Components, such as resistors, inductors, and capacitors, can be arranged in two different ways. In a series circuit, the element's components are connected end to end. The current in a series circuit remains the same in all the electrical elements. In a series circuit, as shown in Figure 6, the sum of the voltages across each element is equal to the voltage of the power source (2).

(2)

In (2), Vout is the voltage output and VA, VB, and VC represent the voltage of the individual components.

Figure 6: A Series Circuit

In a parallel circuit, as shown in Figure 7, the element's components are connected at opposing ends. The current that is supplied by the voltage source equals the current that flows though elements D and E. The voltage across the elements that are parallel is the same (3).

(3)

In (3), Vout is the voltage output and VD and VE represent the voltage of the individual components.

Figure 7: A Parallel Circuit

A digital multimeter will be used in this lab to read the current and voltage across components in circuits. Multimeters usually have two leads that directly touch two nodes in a circuit or the leads of an electrical component. Please read the Digital Multimeter Guidelines before performing this lab in order to understand how to properly operate a digital multimeter. Digital multimeters are indicated by different symbols in electrical circuits, depending on the value being measured by the multimeter. When measuring voltage, the multimeter is referred to as a voltmeter (Figure 8A). When measuring current, the multimeter is referred to as an ammeter (Figure 8B).

Figure 8A: Symbol for Voltmeter
Figure 8B: Symbol for Ammeter

Depending on whether voltage or current is being measured in a circuit, the multimeter will be arranged in the circuit in a different manner. To measure the voltage across an electrical component, the multimeter must be placed in the circuit in parallel (Figure 9A). To measure the current across an electrical component, the multimeter must be placed in the circuit in series (Figure 9B).

Figure 9A: Multimeter in Parallel
Figure 9B: Multimeter in Series

After measuring the voltage and current across a component in a circuit, the electrical power output of that component can be calculated using the Power Law (4).

(4)

In (4), P is the power in Watts, I is the current in Amperes, and V is the voltage in Volts.

The motor provided in the lab is a 9V VEX motor that will operate with voltages lower than 9V with reduced torque and speed (Figure 10). A motor with no load draws 9 mA, and a stalled motor draws well over 350 mA. Increasing the voltage provided to the motor increases the speed. Increasing the current increases torque.

Figure 10: 9V VEX Motor

Design Considerations

  • Which source yields the most voltage per unit cost?
  • Which circuit configuration will provide the most desirable voltage across the load? Parallel or series?

Materials and Equipment

  • TinkerCad

Procedure

This lab is divided into 3 sections: the testing of the power storage device, the investigation of renewable energy sources, and the data analysis of the United States’ renewable energy consumption. The power storage device and power sources will be tested individually. The results of the tests will be used in determining the best power source in designing the sustainable energy vehicle.

In order to create new circuits or copy an existing template of a circuit in Tinkercad, follow the steps below:

  1. Go to tinkercad.com and sign in with an Autodesk account.
  2. To start a new circuit, on the left side of the home screen select Circuit > Create new circuit.
  3. If a template link is provided in the procedure:
    1. Open the Tinkercad link for the part of the lab you want to work on. The links are provided in the procedure below.
    2. Select the Copy & Tinker option. This will copy the template to the workspace so it can be edited.

1. Testing the Power Storage Device

Charging a Capacitor

  1. Open a new Tinkercad circuit. Refer to the Starting the New Tinkercad Circuit procedure to open a new Tinkercad circuit.
  2. The circuit to charge a capacitor will be made in this part of the lab. The circuit is shown in Figure 11.
  3. Click and drag a 9V battery, 1 Farad capacitor, and multimeter on the interface as shown in Figure 11
  4. Wire the negative end of the 9V battery to the negative end of the multimeter. To wire these two components, simply click on the negative terminal of the battery, and click once again on the negative terminal of the multimeter. Red is the positive terminal and black is the negative terminal.
  5. Similarly, wire the positive end of the multimeter to terminal 1 on the capacitor. Wire terminal 2 on the capacitor to the positive terminal of the battery.
  6. Click the “A” on the multimeter to measure ampere.
  7. To charge the capacitor click Start Simulation. Charge the capacitor until the current in the circuit is zero ampere (0A).
  8. Click on Stop Simulation once the multimeter reading is zero ampere (0A).
  9. Take a screenshot of your circuit.
Figure 11: Tinkercad Circuit to Charge a Capacitor

2. Testing the Power Sources

The physical wiring, voltage data, and current data for the wind turbine and the solar panel is given. Calculate the power for each power source.

Table 1: Voltage and Current Data for the Solar Panel and the Wind Turbine
Power Source Solar Panel Wind Turbine
Voltage (V)
5.89 4.24
Current (A)
0.0061 0.0093

Batteries are not the same as capacitors. Batteries are used instead of capacitors because TinkerCAD does not allow for the capacitors to be charged at the beginning of a simulation.

Single Battery in Series with Multimeter

  1. Click and drag one 3V battery, a DC motor, and a multimeter on the interface.
  2. Wire the one 3V battery, the DC motor, and the multimeter in series.
    1. Refer to Figure 6 for how to wire a series circuit.
  3. Click on Start Simulation and record the final current produced by the circuit in series.
  4. Take a screenshot of the circuit with the current reading.

Batteries in Series

  1. Click and drag two 3V batteries, a DC motor, and a multimeter on the interface.
  2. Wire the two 3V batteries, the DC motor, and the multimeter in series.
  3. Click on Start Simulation and record the final current produced by the circuit in series.
  4. Repeat steps 1-3 but with a reversed polarity for one of the batteries. To do this, flip one of the batteries so that it is wired backwards.
  5. Take a screenshot of both circuits with the current reading.

Batteries in Parallel

  1. Click and drag two 3V batteries, a DC motor, and a multimeter on the interface.
  2. Wire DC motor and multimeter in series and the two 3V batteries in parallel.
    1. Refer to Figure 6 for how to wire a series circuit
  3. Click on Start Simulation and record the final current produced by the circuit in parallel.
  4. Repeat steps 1-3 but with a reversed polarity for one of the batteries. To do this, flip one of the batteries so that it is wired backwards.
  5. Take a screenshot of both circuits with the current reading.

Data Analysis

  1. Share and explain the circuits built and the data collected for the wind turbine, solar panel, batteries in parallel, and batteries in series to your group.
  2. Based on the calculated power of each renewable energy source and the results of the analysis of the circuits in series and parallel, determine the best power source and circuit design in order to theoretically power a sustainable energy vehicle with two capacitors.
  3. Sketch the circuit design in your notes and include the polarity on the capacitors and power sources.

3. Case Study: Historical Energy Statistics

In this part, a thorough investigation on the historical trends of renewable energy consumption in the United States will be conducted based on statistical data from the U.S. Energy Information Administration (EIA). In accordance with the data, four graphs will be constructed: a line graph showing the yearly trend for hydroelectric power, geothermal power, solar power, wind power, and biomass power, and a pie chart representing the 2019 distribution in renewable energy. These graphs will then be appended with data regarding fossil fuel energy consumption.

Modeling the Yearly Trend

  1. Download the Excel file containing the raw data for the yearly energy consumption of various renewable energy sources from 1949 to 2019
  2. The line graph will contain multiple lines that represent the different renewable energy sources. The procedure to graph the renewable energy consumption for hydroelectric power is provided. Complete a similar procedure for the remaining renewable energy sources.
    1. On the Excel ribbon, click on the Insert tab, and click “Scatter with Straight Line” on the Scatter option under the Charts group. This should create a blank line graph, as shown in Figure 12.
      Figure 12: Inserting a Line Graph
    2. Right-click on the empty graph and choose the “Select Data” option. A new window will appear where the graphed data can be inputted.
    3. Under the “Legends Entries (Series)” tab, click on the “Add” option, as shown in Figure 13. A new window called “Edit Series” will appear.
      Figure 13: Utilizing the “Select Data Source” Window
    4. In the “Series name” textbox, type in the name of the power source. In this case, type in Hydroelectric Power.
    5. In the “Series X values” textbox, highlight the years in column A from 1949 to 2019.
    6. In the “Series Y values” textbox, highlight the total energy consumption from hydroelectric power in column B that corresponds to 1949 to 2019. The “Edit Series” should appear similar to Figure 14.
      Figure 14: Utilizing the “Edit Series” Window
    7. Click “OK” to graph the Hydroelectric Power data.
  3. Next the data for the remaining renewable energy sources must be added to the same graph. To add the data, repeat steps 2b-g for each renewable energy source.
  4. Rename the axis and titles appropriately. Include a legend by checking off “Legend” in the dropdown menu at the top right of the graph.

Modeling the 2019 Distribution

  1. To visualize the distribution of the various renewable energy sources in recent years, a pie chart will be created based on the 2019 year. This part will continue with the raw data obtained from the previous part.
  2. On the Excel ribbon, click on the Insert tab, and click “2-D Pie” on the Pie Chart option under the Charts group. This should create a blank line graph, as shown in Figure 15.
    Figure 15: Inserting a Pie Chart
  3. Right-click on the empty graph and choose the “Select Data” option. A new window will appear where the graphed data can be inputted.
  4. Under the “Legends Entries (Series)” tab, click on the “Add” option. A new window called “Edit Series” will appear.
  5. In the “Series Values” textbox, highlight each renewable energy sources’ total energy consumption for the 2019 year. Completing this would automatically create five labels under the “Horizontal (Category) Axis Labels” tab, as shown in figure 16.
    Figure 16: Horizontal Axis Labels
  6. Select the row labeled “1” and click on the “Edit” option under “Horizontal (Category) Axis Labels” tab. In the “Axis-label range” textbox, select the names of each renewable energy source (B2:F2) and select OK.
  7. Rename the title appropriately.

Fossil Fuel Energy Modeling

  1. Copy the data in the Fossil Fuel data sheet (located at the bottom left of the excel) to the main data sheet. Ensure that the data on the main sheet is not overwritten by the Fossil Fuel data.
  2. Following the same steps as the “Modeling the Yearly Trend” procedure and “Modeling the 2019 Distribution,” create a new scatter plot and a new pie chart representing both renewable energy sources and fossil fuel energy sources.
    1. For the renewable energy sources scatter plot you should have 5 series: Hydroelectric, Geothermal, Solar, Wind, & Biomass.
    2. For the fossil fuel energy sources you should have 3 series: Coal, Natural Gas, & Petroleum.
    You should have a total of 8 series.

At the end of this case study there should be four graphs in total:

  • a scatter plot containing the renewable energy sources
  • a pie chart showing the 2019 distribution in renewable energy
  • a scatter plot containing both renewable energy sources and fossil fuel energy sources
  • a pie chart showing the 2019 distribution in renewable energy sources and fossil fuel energy sources

Extra Credit

To receive extra credit, predict the expected yearly energy consumption of wind power and solar power for 2030, 2040, and 2050 using Excel. Justify the methodology used to make this prediction. To receive extra credit, this task must be completed with a reasonable justification before the end of the lab and also must be included in the team presentation.


Assignment

Individual Lab Report

Follow the lab report guidelines laid out in the EG1004 Writing Style Guide in the Technical Writing section of the manual. Use the outline below to write this report.

  • Define renewable energy
  • Explain how solar panels and wind turbines work
  • Explain the concept of the capacitor
  • Discuss the advantages and disadvantages of both energy sources
  • Discuss the power sources and their power output. How did the voltage measurements of the power sources impact the power?
  • Specify the power source chosen for the design
  • Include the graphs for the renewable and nonrenewable energy trends
  • Based on the yearly trend for renewable energy consumption, discuss the qualitative changes in renewable energy in the past twenty years. Briefly research why these changes occurred
  • Based on both the yearly trend for renewable energy consumption and the 2019 distribution, what is the dominant source of renewable energy? Do you think it will remain the dominant source of renewable energy in the future?
  • Compare the yearly renewable energy trends with the fossil fuel energy trends. Discuss the modern energy consumption profile
  • Include screenshots of the batteries in parallel and batteries in series circuits.
  • Discuss what part of the lab you completed for your group and why it was important to the overall experiment.

Remember: Lab notes must be taken. Experimental details are easily forgotten unless written down. EG1004 Lab Notes paper can be downloaded and printed from the EG1004 Website. Use the lab notes to write the Procedure section of the lab report. At the end of each lab, a TA will scan the lab notes and upload them to the Lab Documents section of the EG1004 Website. One point of extra credit is awarded if the lab notes are attached at the end of the lab report. Keeping careful notes is an essential component of all scientific practice.

Team PowerPoint Presentation

Follow the presentation guidelines laid out in the EG1004 Lab Presentation Format in the Technical Presentations section of the manual. When preparing the presentation, consider the following points.

  • Discuss why you chose your renewable energy source
  • Discuss the power sources and their power output. How did the voltage measurements of the power sources impact the design?
  • Discuss why you chose to have the capacitors in series or parallel
  • Discuss your renewable energy consumption graphs and the trends observed
  • Discuss the overall energy consumption graphs and the trends observed

References

Layton, J.. "How Wind Power Works." How stuff works. Discovery, 2011. Retrieved 24 July 2012. <http://science.howstuffworks.com/environmental/green-science/wind-power.htm>.

Locke, S.. "How Does Solar Power Work." Scientific American. Scientific American, 2008. Retrieved 24 July 2012. <http://www.scientificamerican.com/article.cfm?id=how-does-solar-power-work>.

NextEra Energy Resources, LLC. "Benefits of Renewable Energy." NextEra Energy Resources. NextEra Energy Resources, 2012. Retrieved 24 July 2012. <http://www.nexteraenergyresources.com/content/environment/benefits.shtml>.

Perlman, Howard.. "Hydroelectric Power: How it Works." U.S. Geological Survey, 2016. Retrieved 4 Jan 2018. <https://water.usgs.gov/edu/hyhowworks.html>.

Reg Tyler, . "Types of Fuel Cells." Energy efficiency and renewable energy. U.S. Department of Energy, 2011. Retrieved 24 July 2012. <http://www1.eere.energy.gov/hydrogenandfuelcells/fuelcells/fc_types.html>.