Difference between revisions of "Revit-How-To Guide"

From EG1004 Lab Manual
Jump to: navigation, search
Line 123: Line 123:


For ceiling lights, go back to the Level 1 Ceiling Plan in the Project Browser. Select the lights that are to be placed with the Component tool in the Architecture tab of the ribbon. Once the lighting fixture is selected, select Modify | Place Component → Placement → Place on Face tab of the ribbon to place the lights on the ceiling (Figure 17).
For ceiling lights, go back to the Level 1 Ceiling Plan in the Project Browser. Select the lights that are to be placed with the Component tool in the Architecture tab of the ribbon. Once the lighting fixture is selected, select Modify | Place Component → Placement → Place on Face tab of the ribbon to place the lights on the ceiling (Figure 17).
[[File:Place_on_Face_Tool.png|600px|thumb|center|Figure 17: Place on Face Tool]]
For components that are not in the default Revit library, you can visit websites such as RevitCity and BimObject. From there, you can download various components and place them as you would other components.
== Stairs & Staircases ==
Before you add in stairs, you have to create a shaft (a hole in the ceilings and floors). In the Architecture tab, select <b>Shaft</b> (Figure 18).
[[File:Shaft_Tool.png|600px|thumb|center|Figure 18: Shaft Tool]]
Draw out the area of the shaft. It is recommended that the shaft you draw now is larger and you make it smaller after the staircase is placed.
[[File:Example_Shaft_over_Multiple_Levels.png|600px|thumb|center|Figure 19: Example Shaft over Multiple Levels]]
Add stairs with the “Stair” function. Place the stairs in the created shaft, you might have to adjust the “desired number of risers”(in the properties tab, under dimensions) and the “actual run width”(just under the project ribbon) so that your stairs cover the length of the entire shaft.  Alternatively, you could make the shaft smaller to fit the stairs. To copy the stairs over multiple levels, select <b>Connect Levels</b>, a dialogue box will ask you to open a view, open any of the elevation views or 3D view and select all levels(Ctr+Click allows you to select multiple levels).  Finally, click on the green check mark to finish editing.
[[File:Example_Staircase.png|600px|thumb|center|Figure 20: Example Staircase]]
== Curtain Walls ==
Curtain walls are made of three components: The grid, mullions, and panels. To create a curtain wall, first select a regular wall. Then, in the properties dropdown menu, select Curtain Wall (Figure 21).
[[File:Selecting_Curtain_Walls.png|600px|thumb|center|Figure 21: Selecting Curtain Walls]]
To automatically add curtain grids, select curtain wall, then select edit type in the properties browser. Under Vertical Grid → Layout, select Maximum Distance to equally divide your curtain wall, or select Fixed Distance to specify the distance between grids (Figure 22).
[[File:Grid_Spacing.png|400px|thumb|center|Figure 22: Grid Spacing]]
To automatically add mullions, in the same properties screen as step 4, scroll down to Vertical Mullions or Horizontal Mullions, and select the type of mullion desired (Figure 23).
[[File:Mullion Spacing.png|400px|thumb|center|Figure 23: Mullion Spacing]]
If there is a solid wall in place, a curtain wall can be embedded in it. Select the curtain wall, then in the same Edit Type menu from the previous two steps, then check the box next to Automatically Embed. Hover over the wall centerline of the wall you want to embed the curtain wall in, then place the curtain wall (Figure 24).
[[File:Embedding_a_Curtain_Wall.png|400px|thumb|center|Figure 24: Embedding a Curtain Wall]]
= Plumbing =
== Setting up a New File ==
Similar to how an Architectural plan was made, select “New” under the Projects heading, then select Browse in the pop up menu, then open the template file named “Plumbing-Default.rte” (Figure 25).
[[Filw:Lab_RevitPlumbingDefault.jpg|400px|thumb|center| Figure 25: P Creating a Plumbing Plan File]]
Insert the architectural model by going to the “Insert” tab, then selecting Link Revit. Find the file name and select open (Figure 26).
[[File:Lab_RevitLinking.jpg|400px|thumb|center| Figure 26: Linking Architectural Design]]
Hover over the design and left click once you see a blue box surrounding it. This should highlight every element in the design (Figure 27).
[[Image:Lab_RevitHighlight.jpg|400px|thumb|center| Figure 27: Highlighted Elements]]
Select the pin icon under the <b>Modify</b> tab (Figure 28).
[[Image:Lab_RevitPinTool.jpg|400px|thumb|center| Figure 28: Pin Icon]]

Revision as of 03:42, 5 April 2022

Architectural

Setting up

Open Revit. Select New, then select Architectural Template (Figure 1). Each template is used for a different type of design. For architectural designs, this template will be used.

Figure 1: Revit 2022

There are four major sections used to create and modify a design in Revit. The Quick Access Toolbar is highlighted in red, the Project Ribbon is highlighted in yellow, the Properties panel is highlighted in green, and the Project Browser panel is highlighted in blue (Figure 2). If any of the sections are accidentally removed from view, they can be reinserted by going to View → User Interface (rightmost icon) in the ribbon.

Figure 2: Revit Interface

An important aspect of setting up your project is defining the levels (the story heights for the building). Navigate to one of the elevation views, in this case the East elevation, in the Project Browser by double clicking (Figure 3). Each plan view or elevation view will open in a new “tab” that you can toggle between.

Figure 3: Project Browser

To add a new level, select Level in the Architecture tab (Figure 4). Click a point above the current top level, usually 10’, then move your cursor horizontally and click again to place the level. To delete a level, just click on it and press “Delete” on your keyboard.

Figure 4: Level Tool

To view your 3D model, go to the “View” tab in the toolbar, under the “Create” subtab, and click “3D View” (Figure 5).

Figure 5: 3D View Icon

Along the bottom of your window is a toolbar with various symbols. Hover over each symbol to figure out what each one does. The most important functions in this toolbar are the two symbols highlighted below (Figure 6). The first is the Visual Style for the model. The Wireframe view is the most useful style to work in because you can see through all your objects. If you would like to hide certain objects while you are drawing, right click on it and click “Hide in View”. Hiding an element means only hiding the object you selected. Hiding a category means hiding every object that is in the same category as the object you selected (ex: hiding all furniture). The Reveal Hidden Elements function (the lightbulb symbol), when clicked, shows everything that you have hidden in pink, along with your existing structure. These two functions are helpful when you want to build on the interior of your structure, but your walls are blocking your vantage point.

Figure 6: Bottom Toolbar

Building

In the Project Browser column, go back to Level 1 under “Floor Plans”. You should always be building from the ground up, so start at Level 1. To start, select the “Wall” function under “Build” in the “Architecture” tab of the toolbar (Figure 7). Build an Architectural Wall.

Figure 7: Wall Tool

When you click on the function, a new tab called “Modify” should appear on the far right of the toolbar. This happens for any new structure you select under Build. Click what type of line or shape you would like to draw and draw it on your view (Figure 8).

Figure 8: Draw Tool

In general, your walls should be 10’ high, but this can be customized per your design. Exterior walls should be 8” thick while interior walls should be 6” thick. The thickness of the wall can be changed in the drop-down menu in the Properties panel (Figure 9).

Figure 9: Changing Wall Types

If you made a mistake in the length of your walls in your initial drawing, you can always double click on the dimension in blue and change it manually by typing in the correct value (Figure 10). Once you are done modifying the wall,or placing any component, press the “Esc” key to reset to the main screen.

Figure 10: Modifying Wall Dimension

Figure 10. Modifying Wall Dimension There are other elements of the wall, or any component, that can be changed in the Properties pane (Figure 11). The Base Constraint changes where the bottom of the wall is placed in reference to the different levels. The Base Offset adjusts the height difference between the level and the base of the wall. The Top Constraint determines where the top of the wall is located. If the top constraint is unconnected, then the Unconnected Height can be used to determine a numerical value for the height of the wall.

Figure 11: Wall Properties

After you have created walls for your structure (just on Level 1), you can add floors, ceilings, doors, and windows.

For floors and ceilings, you will need to provide a “boundary” that your floor or ceiling will follow. This boundary is the perimeter of your building that you created when you build your walls. Click “Floor”, and under the Modify tab, it will prompt you to pick a line type to draw your boundary with. “Boundary Line” should already be automatically selected. Simply click on your walls that you created, then click the green check mark. You can also create individual lines by selecting the Line tool. The arrows that appear when placing the floor allows you to toggle between the inside or the outside of your wall as the boundary (Figure 12).

Figure 12: Placing a Floor

To insert a ceiling or ceiling appliance, select the Ceiling Plans in the Project Browser. Go to Level 1 in the Ceiling Plans (Figure 13).

Figure 13: Ceiling Plans

The ceiling is created with the same method as the floor, by selecting a boundary where the ceiling will be placed. Use the Ceiling tool in the Architecture tab of the ribbon to create the ceiling. The individual walls can be selected to create the boundary by creating a Sketch Ceiling tool, or entire areas can be selected for the boundary using the Automatic Ceiling (Figure 14). Complete the ceiling by clicking the green check mark in the ribbon.

Figure 14: Sketch Ceiling and Automatic Ceiling Tools

To create a roof, go to the highest level Floor Plan, and select Roof in the Architecture tab, and draw its footprints around the walls (same as a boundary). As you draw in the footprints, you can edit the slope of each portion to your liking (Figure 15). After drawing your roof footprint and clicking the green check mark, Revit will ask you if you would like to attach the highlighted walls to the roof.

Figure 15: Adding a Roof

Components

Doors and windows can be placed by selecting the respective option in the Architecture tab. They can be placed by clicking in the floor plan. Once placed, the direction of the doors and windows can be changed with the arrow couples (Figure 16).

Figure 16: Door Direction Arrow Couples

When loading furniture or appliances, go to the Architecture tab of the ribbon and select Component → Place a Component (or type CM). Furniture and appliances can be added with the Load Family tool. Some common appliances are provided in the table below.

Table 1: File Paths for all Furniture and Appliances Tab
Components File Paths
Sink
English → Plumbing → MEP → Fixtures → Sinks
Toilet
English → Plumbing → MEP → Fixtures → Water Closets
Shower
English → Plumbing → MEP → Fixtures → Shower
Bed
English → Furniture → Beds
Kitchenette
English → Specialty Equipment → Domestic
Table
English → Furniture → Tables
Desk
English → Furniture → Tables
Door
English → Door → Residential
Table 2: File Paths for Architecture Tab
Components File Paths
Light Switch
US Imperial → Electrical → MEP → Electric Power → Terminals → Lighting Switches
Ceiling Light
US Imperial → Lighting → MEP → Internal

For ceiling lights, go back to the Level 1 Ceiling Plan in the Project Browser. Select the lights that are to be placed with the Component tool in the Architecture tab of the ribbon. Once the lighting fixture is selected, select Modify | Place Component → Placement → Place on Face tab of the ribbon to place the lights on the ceiling (Figure 17).

Figure 17: Place on Face Tool

For components that are not in the default Revit library, you can visit websites such as RevitCity and BimObject. From there, you can download various components and place them as you would other components.

Stairs & Staircases

Before you add in stairs, you have to create a shaft (a hole in the ceilings and floors). In the Architecture tab, select Shaft (Figure 18).

Figure 18: Shaft Tool

Draw out the area of the shaft. It is recommended that the shaft you draw now is larger and you make it smaller after the staircase is placed.

Figure 19: Example Shaft over Multiple Levels

Add stairs with the “Stair” function. Place the stairs in the created shaft, you might have to adjust the “desired number of risers”(in the properties tab, under dimensions) and the “actual run width”(just under the project ribbon) so that your stairs cover the length of the entire shaft. Alternatively, you could make the shaft smaller to fit the stairs. To copy the stairs over multiple levels, select Connect Levels, a dialogue box will ask you to open a view, open any of the elevation views or 3D view and select all levels(Ctr+Click allows you to select multiple levels). Finally, click on the green check mark to finish editing.

Figure 20: Example Staircase

Curtain Walls

Curtain walls are made of three components: The grid, mullions, and panels. To create a curtain wall, first select a regular wall. Then, in the properties dropdown menu, select Curtain Wall (Figure 21).

Figure 21: Selecting Curtain Walls

To automatically add curtain grids, select curtain wall, then select edit type in the properties browser. Under Vertical Grid → Layout, select Maximum Distance to equally divide your curtain wall, or select Fixed Distance to specify the distance between grids (Figure 22).

Figure 22: Grid Spacing

To automatically add mullions, in the same properties screen as step 4, scroll down to Vertical Mullions or Horizontal Mullions, and select the type of mullion desired (Figure 23).

Figure 23: Mullion Spacing

If there is a solid wall in place, a curtain wall can be embedded in it. Select the curtain wall, then in the same Edit Type menu from the previous two steps, then check the box next to Automatically Embed. Hover over the wall centerline of the wall you want to embed the curtain wall in, then place the curtain wall (Figure 24).

Figure 24: Embedding a Curtain Wall

Plumbing

Setting up a New File

Similar to how an Architectural plan was made, select “New” under the Projects heading, then select Browse in the pop up menu, then open the template file named “Plumbing-Default.rte” (Figure 25).

400px|thumb|center| Figure 25: P Creating a Plumbing Plan File

Insert the architectural model by going to the “Insert” tab, then selecting Link Revit. Find the file name and select open (Figure 26).

Figure 26: Linking Architectural Design

Hover over the design and left click once you see a blue box surrounding it. This should highlight every element in the design (Figure 27).

Figure 27: Highlighted Elements

Select the pin icon under the Modify tab (Figure 28).

Figure 28: Pin Icon