Prototyping with Microcontrollers, Sensors, and Materials (Virtual)

From EG1004 Lab Manual
Jump to: navigation, search

Objective

The objective of this lab is to utilize electrical components, an Arduino board, and the Arduino IDE (Integrated Development Environment) to control an LED without and with a button, to take temperature readings, and to evaluate the design a prototype for a product. The Arduino IDE will be used to program the Arduino board.

The prototyping will focus on the design of a thermal insulation device, the testing of the device, and the analysis of the resulting data. The designs will be measured by their capacity to slow the rate of heat loss from hot wax placed inside them. The design will be entered in a competition that will be judged by a ratio that uses the cost of the device, its insulating capacity, the final temperature of the melted wax inside the device, and the room temperature. The lowest design ratio wins.

For the virtual semester, the competition will not be conducted, but a predetermined thermal insulation device design and its associated data will be given to you to analyze. You will still have to conduct the data analysis for the design that is given to you. Extra credit will be offered in the form of constructing your thermal insulation device with materials at home.

Overview

Prototyping

Prototyping is the process of designing and building an early model of a product to test a concept or process. Any system or device that will be sold to consumers, government agencies, or businesses will begin as a prototype that typically does not have all of the components or functions that will be used in the product that is eventually brought to market. A prototype can serve as a proof of concept showing that the system or device can be built and will perform correctly. In this lab, a prototype of a thermal insulation device will be built. Its function will be to reduce the rate of heat loss from a container of heated wax placed in the device. The prototype insulating device will use a TMP 36 sensor to measure heat loss and it will be operated by a microcontroller.

Electricity

Electricity is the movement of electrons. Electrons flow through a conductive wire when there is a difference in charge between two points in the wire. This flow of electrons is the electrical current and it is measured in amperes (A). Electrical current flows in the opposite direction of the electrons. The difference in charge is the electrical voltage and is measured in volts (V). Certain materials resist the flow of electrons. This property is electrical resistance and is measured in ohms (Ω). Ohm’s Law (1) describes the relationship of the voltage across a resistor, the current (I) flowing through a resistor, and the resistance (R) of the resistor.

(1)

Variations in voltage and current are also used in digital signal processing to operate complex systems and devices and simpler devices, such as microcontrollers and household digital instruments.

Electrical Components

Several basic electrical components are used to build simple circuits. Some of these components are polarized, which means the way they are connected affects their functionality.

Breadboards

Breadboards (Figure 1) are small boards that are commonly used for circuit prototyping. They allow the circuit’s components to be connected without making permanent connections. The red and blue strips on the sides of the board (sections A and D) called power rails are connected down the board and are usually used for powering and grounding. The non-colored rows between the power and ground strips (sections B and C) are connected across and are usually used for making the connections between components and sensors. Sections B and C are not connected to each other across the bridge in the middle of the board.

Figure 1: Breadboard Connections

DC (Direct Current) Voltage Sources

DC voltage sources are used to power circuits because they have a voltage difference across their terminals. DC voltage sources are usually batteries (e.g. AA, AAA). Arduino boards can be powered by a battery, a USB cable, or an AC adapter. When the Arduino is powered, it can be used as a 5V DC voltage source. They are polarized.

Resistors

Resistors (Figure 2) are components that reduce the current flowing through a circuit and convert the excess current to thermal energy. Resistors can be used to control the voltage and current of circuits. Resistors are color coded to indicate their resistance (Figure 3). They are not polarized.

Figure 2: Symbol for a Resistor

Figure 3: Resistor Color Codes

Push-Buttons and Switches

Push-buttons and switches (Figure 4) are mechanical devices that interrupt or divert current. Basic push-buttons are polarized while basic switches are not.

File:Button switch.jpg
Figure 4: Symbols for Buttons and Switches

Diodes and Transistors (BJT/MOSFETs)

A TMP36 sensor (Figure 5) uses the voltage-temperature relationship of diodes to measure temperature. Essentially, the voltage across the diode of the sensor will change proportionally to the temperature. The output voltage can then be converted to a temperature reading.

Figure 5: TMP36 Sensor

Diodes and transistors (Figure 6) allow current to only pass in one direction. MOSFETs are electrically controlled switches. They can also be used to amplify signals. They are polarized.

Figure 6: Symbols for Diodes and Transistors

Light Emitting Diodes

Light emitting diode (LED) is a small electric light that uses low voltage and current (Figure 7). The orientation of an LED is important since it is a diode and only allows current to flow in one direction. Most LEDs also require a resistor (typically 470 Ω) in series because they will burn out almost instantly when they encounter high current. They are polarized.

LED.jpg

Figure 7: Symbol for an LED

Microcontrollers

A microcontroller is an inexpensive, programmable computer without any peripherals, such as a mouse, keyboard, or screen. Microcontroller boards have direct access to the input and output pins of their processing chips so that the user can directly read from sensors and perform actions. Microcontrollers are used in many electrical appliances, such as microwaves. Arduino boards (Figure 8), which use a microcontroller, were designed to be easily programmed and assembled into larger projects. These boards come in many shapes and sizes and some contain additional features, such as WiFi or Bluetooth connectivity. Different boards can also have different features, such as processing speed and memory.

Figure 8: Arduino UNO

This lab will use an Arduino UNO board created by SparkFun called a RedBoard (Figure 9). A RedBoard has many of the basic functions of a computer.

Figure 9: RedBoard

Arduino Hardware

All Arduino boards have a general layout is similar to that shown in Figure 10. Not all the sections and pins will be used in this lab or for the Semester Long Design Projects.

Figure 10: RedBoard Layout
  • Reset Button: Restarts the board
  • USB Connector: Provides power and connects it to the computer
  • Pin 13 LED: Usable LED without making an LED circuit
  • Serial LEDS: Shows if the Arduino is transmitting or receiving data from pins 0, 1, or the USB connection

The power pins are used to supply voltage to other pins, and are also used to ground pins (Figure 11).

Figure 11: RedBoard Power Pins
  • 3.3V: Usually used to power low-voltage sensors
  • 5V: Most common power pin used to power circuits
  • GND: Ground pin, which is 0V
  • VIN: Voltage-in can be used to power the board using a battery or other external voltage source

The digital and analog pins are used for input and output commands to the microcontroller and electrical components (Figure 12). They can be used with both analog and digital devices, as the Arduino board converts analog inputs to a digital input.

Figure 12: RedBoard Digital (Left) and Analog (Right) Pins
  • A0-A5: Identical analog pins that can be used to read sensors or control analog devices. Pins A0-A3 are more stable than A4 and A5
  • Pins 0-1: Transmitter and receiver pins. Do not use these pins for this lab
  • Pins 2-12: Digital pins that can be switched between HIGH states and LOW states
  • Pin 13: Connected to the onboard LED, use it only as an input pin

Arduino IDE

The Arduino IDE is a program that can be used to edit, compile, and upload code to a supported microcontroller. Figure 13 is a screenshot of the program.

Figure 13: Arduino IDE Interface
  • Verify: Checks code for errors and points to the errors after it finishes
  • Upload: Verifies code and then uploads it to the Arduino board if there are no errors
  • Console: Shows any errors the software found in the hardware
  • Serial Monitor: A tool used to send messages to and receive messages from the board


Programs written in Arduino are called sketches. A basic sketch can be broken up into three different areas: global, setup, and loop. These areas are pictured in Figure 14.

Figure 14: Areas in Arduino IDE Sketch
  • Global: Constants and imported libraries go here
  • Setup: Activate the pins and sensors used. This code only runs once
  • Loop: The code that runs continuously for reading sensors and turning pins HIGH or LOW

Arduino Programming

The Arduino programming language is based on C/C++, but it is designed to be simpler and easier to learn. The most intuitive way to think about programming is like building with LEGO blocks: certain rules must be followed and different building blocks can be used to build bigger parts.

Every line must end with a semicolon (;) unless it is a conditional, loop, or function. Comments start with two backslashes (//). Comments are text that the program ignores and are used to label and explain code.

Datatypes

Datatypes are the different kinds of data values that can be used, manipulated, and stored using C++. Table 1 shows the most basic and widely used datatypes.

Table 1: Datatypes
Datatype What It Stores (Examples) Default Value Notes
Boolean
True value (1, HIGH) or
false value (0, LOW)
0, FALSE, LOW -
int
Integer number (e.g. -5, 15, 1047) 0 Positive or negative
double
Decimal number (e.g. -0.5, 123.77) 0 Positive or negative
char
Single character (e.g. ‘c’, ‘A’, ‘5’, ‘?’) Indeterminate Enclosed in single quotes
string
Sequence of characters (e.g. “Hello World!”, “10”, “157+5”) Empty (“”) Enclosed in quotes

Operators

Operators perform operations on variables and constants. The results of these operations are usually stored in a variable. Table 2 displays common operators.

Table 2: Operators
Operator What it Does Notes
= Assigns a value to a variable -
+ Adds two or more values -
- Subtracts two or more values -
* Multiplies two or more values -
/ Divides two or more values -
++ Increment by 1 Usually used in loops
-- Decrement by 1 Usually used in loops
== Checks if two values are equal Usually used in conditionals
!= Checks if two values are not equal Usually used in conditionals
> or < Less than, greater than comparison Usually used in conditionals
<= or >= Less than, greater than, or equal to comparison Usually used in conditionals
&& or || Boolean AND or Boolean OR ssed to cascade multiple Boolean operations Usually used in conditionals

Constants and Variables

Constants and variables (Figure 15) hold data according to their datatype. They must be given a name so they can be referred to later. Constants hold data that will not change while a program is running. Constants usually contain pin numbers or sensor threshold values. Variables contain data that will change while a program is running. Variables usually contain sensor values and other values that must have mathematical operations done on them. Figure 15 shows how to create different constants and variables.

Figure 15: Constants and Variables

Conditional Statements

Conditional statements (Figure 16) run code enclosed by their curly brackets when a condition is met.

Figure 16: Conditional Statements

Loops

Loops (Figure 17) run the code enclosed by their curly brackets a specific number of times or until a condition is met. While loops are used to perform a task until a condition is met. In Figure 17, the while loop runs only if the state of the button is HIGH. When the state of the button becomes LOW, the while loop will immediately stop running. For loops are used when an action must run a specific number of times. Although they seem complicated at first, the structure of most for loops is the same. In Figure 16, the first part of the for loop sets a variable (usually i for index) to a value used to begin a count, the middle sets the condition to make the loop stop, and the third part is where the variable is incremented or decremented with each run of the loop. The first time the loop runs, i = 0 which does not meet the loop end condition (i > 10) and the code will run. At the end of the loop code, i is incremented by 1 and becomes i = 1. For the second time the loop runs, i = 1 which again does not meet the loop end condition and the code runs once again. i then becomes i = 2 at the end of the loop. This repeats until i = 10.

Figure 17: While and For Loops

Commonly Used Arduino Functions

Table 3 shows commonly used functions in the Arduino IDE that are specifically used to work with the digital and analog pins of the board.

Table 3: Commonly Used Arduino Functions
Function What it Does
pinMode(pin, mode) Sets a pin as an input or output
digitalWrite(pin, value) Sets a digital output pin to HIGH or LOW
digitalRead(pin) Reads a digital input pin as HIGH or LOW
analogWrite(pin, value) Sets an analog output pin to a value 0-1023
analogRead(pin) Reads an analog output pin as a value 0-1023
delay(milliseconds) Pauses program for a certain amount of time
Serial.print(value) Prints the value (variable) to the Serial Monitor

TinkerCAD

Heat and Heat Transfer

Heat is a form of energy. Heat can be beneficial and it can be destructive. For example, the heat created by the combustion of fossil fuels in a combustion engine or the heat generated by the friction between parts of an engine in contact can destroy an engine. A heating, ventilation, and air conditioning (HVAC) system in a home keeps the home warm at cooler temperatures and cool at warmer temperatures. Many systems and devices use components and materials that are designed to remove heat from the system or retain heat in the system.

Heat transfer is the process of thermal energy moving from one body to another as a result of a temperature difference. Temperature is the measure of the average kinetic energy of atomic motion. The faster the atoms are moving, the higher the temperature. The main mechanisms of heat transfer are conduction, convection, and radiation.

Conduction occurs when there is a temperature difference within a solid body or between solid bodies in contact. During conduction, energy (heat) will flow from the region of higher temperature to the region of lower temperature. Imagine a metal rod that is heated at one end. The atoms of the rod collide at the point where the temperature differs, transferring heat until the temperature of the rod becomes uniform.

Convection is the transfer of heat within a fluid medium (fluids consist of gasses and liquids). Convection can occur as natural or forced convection. Forced convection (Figure 18) occurs when the main mechanism for heat transfer is due to an outside force causing the fluid to move. Natural convection results from the natural difference in density between fluids, causing a liquid or gas to rise.

Figure 18: Air Circulation Diagram

Radiation is the process by which energy in the form of electromagnetic radiation is emitted by a heated surface in all directions. It does not require an intervening medium to carry it. The heating of the Earth by the Sun is an example of heat transfer by radiation. Electromagnetic radiation is a means of energy transfer that occurs when an atom absorbs energy. This electromagnetic wave can propagate as heat, light, ultraviolet, or other electromagnetic waves depending on the type of atom and the amount of energy absorbed.

Color is a property of light. When an object appears white, it virtually reflects all the electromagnetic waves coming to it while a black object absorbs the waves. Color (reflectivity) should be considered when choosing materials for thermal insulation.

The container that will be built in the lab is a thermodynamic system (Figure 19), which is a part of the Universe separated from the surroundings by an imaginary boundary. There are three types of systems: open systems, closed systems, and isolated systems.

Figure 19: Thermodynamic System

Open systems allow the transfer of mass and heat. For example, an open pot of boiling water is an open system. It exchanges heat and water vapor with the air around it. If collected, the water vapor can be condensed back to liquid water that has some mass.

Closed systems only allow heat to be transferred to the surroundings. A hermetically sealed bottle of soda is a closed system. If placed in a hot environment, it absorbs energy in the form of heat, but the amount of liquid within does not change.

Isolated systems do not interact with the surroundings at all. No exchange of heat or mass is possible. An ideal Thermos® is an isolated system. If hot chocolate is poured within, the same amount at the same temperature will be poured out later. No such system can be fabricated, but they can be approximated.

Understanding how to minimize heat loss is the key to designing a successful insulating container. The first consideration is the materials chosen. Using materials that are poor conductors of heat, such as glass, will minimize heat loss. Plastic is also a poor conductor of heat. Foam cups are made of plastic that has tiny air bubbles suspended in it. Air is among the poorest conductors of heat. A vacuum, or the complete lack of air, is the best insulator of all. This is the principle employed in the Thermos® design.

The other important consideration in creating the container is its cost. Minimal design uses the fewest resources while maintaining the safety and efficacy of a product.

Materials and Equipment

The following are the materials that can be used in TinkerCAD:

  • Arduino UNO microcontroller
  • TinkerCAD code block with Arduino IDE
  • Breadboard
  • Wires
  • Resistors
    • 220 Ω
    • 10 kΩ
  • LED
  • Push-button
  • TMP 36 Sensor

Procedure

1. Starting a New Circuit in TinkerCAD

TinkerCAD is an online 3D modeling program and will be used in this lab to simulate the circuits.

  1. Go to tinkercad.com and sign in with an Autodesk account.
  2. Open the TinkerCAD link for the part of the lab you want to work on. The links are provided in the procedure below.
  3. Select the Copy & Tinker option. This will copy the template to the workspace so it can be edited.


2. LED Circuit

  1. Copy the Part 1 template to the TinkerCAD workspace using the steps in Starting a New Circuit in TinkerCAD.
  2. A continuous blinking LED circuit will be made in this part of the lab. The programming flowchart and circuit diagram are shown in Figure 20.
    Figure 20: LED Circuit Diagram and Flowchart
  3. Click and drag the LED and resistor to the breadboard as shown in Figure 21. Set the resistor to 220 Ω. Remember, since LEDs are polarized, their orientation matters.
  4. The shorter leg (negative end) of the LED should be connected to the same row as GND on the Arduino board. The resistor is necessary, otherwise too much current would flow through the LED burn it out.
  5. Wire the signal from digital pin 7 to the LED directly. To wire these two components, simply click on a hole in the same row as the negative terminal of the LED, and click once again on the GND pin of the Arduino.
  6. Wire the remaining components in a similar fashion as shown in Figure 21 to complete the circuit.
    Figure 21: LED Circuit
  7. Type the code shown in Figure 22 into the code block at the top of the TinkerCAD workspace.
    Figure 22: LED Circuit Code
  8. The flowchart uses digital pin 7 on the Arduino board as an output, so create a constant that holds the number 7 (top line of code in Figure 22).
  9. In the setup area, set pin 7 as an output using pinMode (second block of code in Figure 22).
  10. Turn the LED on by using digitalWrite, have a delay of one second, turn the LED off by using digitalWrite, and then set another delay of one second (third block of code in Figure 22). The delays are necessary as the LED is a bit slow to react.
  11. Use the debugger on the Code block. This allows you to see errors in your code so you can fix them before you run the simulation.
  12. Once you fix all errors, click Start Simulation.
  13. If the code is correct, the LED will turn on and off after every second. If that doesn’t happen, check the wiring and code again.
  14. Screenshot the final code, circuit, and results (with the LED lighting up).

3. LED with Button Circuit

  1. Copy the Part 2 template to the TinkerCAD workspace using the steps in Starting a New Circuit in TinkerCAD.
  2. In this part of the lab, a button will be added to the blinking LED circuit, which requires conditional statements (if-statements) in the code. The LED should only turn on when the button is pressed.
  3. Before breadboarding the circuit, look at the button to determine which pins are connected. With an actual button, this is done by checking the bottom side (pin side) of the button (Figure 23). Note which pins are for power, ground, and digital input into the Arduino. In TinkerCAD, the button is depicted with the pins extending from the sides, which shows the direction of the pin orientation.
  4. Place the button on the breadboard and make sure it straddles the bridge down the center of the breadboard (Figure 23).
    Figure 23: Button Circuit Diagram
  5. Breadboard the circuit diagram as shown in Figure 24.
    Figure 24: LED with Button Circuit
  6. Write the Arduino program to implement the flowchart in the Code block at the top of the TinkerCAD workspace. Use an if-statement. Refer to the Conditional Statements part of the Overview for help with writing if-statements.
  7. Remember to create a constant to hold the pin number that the button is connected to and ensure that the button will be a digital input. After creating the button constant, create an integer that will hold the button state, as shown in Figure 25.
    Figure 25: Button Integer Setup Code
  8. Within the loop function, check the state of the button (whether it is pressed or not pressed), using the code in Figure 26.
    Figure 26: Button State Code
  9. Use the debugger in the Code block and click Start Simulation to check your code.
  10. Screenshot the final code, circuit, and results (the LED state when the button is pressed and is not pressed), and send the files to yourself.

4. Prototyping a Thermal Insulation Device

Note: Data will be provided to you for this portion of the lab as it cannot be conducted virtually. Read the procedure below to familiarize yourself with how the TMP 36 circuit that will be built later will be used. You do not have to do anything for this part of the lab. It is not a competition lab for the virtual semester.

A thermal insulation device will be prototyped, and its ability to insulate heat from hot wax will be measured with a thermistor. The measurement system involves Arduino circuitry and programming. Your design will be entered into a competition against other thermal insulation device prototypes in the section. The design with the highest competition ratio wins.

The following rules must be observed at all times during the competition. Violation of any of these rules will result in disqualification. The placement of the thermistor with respect to the lid may not be changed.

  • The thermal insulating device may not be held while testing
  • External heat sources are prohibited
  • The jar of beeswax must be inside the container within 30 seconds of it being received
  • The jar of beeswax cannot be returned (no restarts)
  • At least one item from Table 4 must be used in the design of the insulating device
  • The competition will be judged by the minimal design ratio (MDR) (2) of the design. The design with the lowest MDR wins

(2)

  • In (2), IC is the insulating capacity, Cost is the cost of the container, TR is the temperature of the room, and TF is the final temperature read by the thermistor. Ask a TA for the room temperature
  • The insulating container will be built using the materials in Table 4. Select the materials carefully. Consider their cost and their use as an insulator. Review the competition ratio before purchasing materials.
Table 4: Materials and Costs
Material Unit Cost Per Unit
Large foam cup 1 $0.50
Small foam cup 1 $0.25
Lid 1 $0.25
Sand 1 cup $0.40
Pack of clay 1 bag $0.20
Wool fabric 2 pieces $0.10
Styrofoam pieces 5 $0.05
Cotton balls 3 balls $0.05
Tape 1 ft $0.10
Aluminum foil 1 ft2 $0.30

Note that in the lab, a thermistor is used instead of a TMP 36 sensor. A thermistor also converts an analog reading to a temperature, similar to the TMP 36 sensor. A TMP 36 sensor will now be built in the following section.

5. Building a TMP 36 Circuit

Using the Arduino, the temperature change of the hot wax will be recorded over 15 minutes. The Arduino will read the temperature through the TMP 36 sensor and print the values into the Serial Monitor in the Arduino IDE. Because this lab is performed virtually, you will create the TMP 36 circuit virtually in TinkerCAD, but will not be able to measure a thermal insulation device. You will complete the circuit for collecting data and test it as if you were to collect the data for 15 minutes in-person and then receive the Serial Monitor readings from a Lab TA.

  1. Copy the Part 3 template to the TinkerCAD workspace using the steps in Starting a New Circuit in TinkerCAD.
  2. Wire the circuit according to the configuration in Figure 27. A 10 kΩ (Brown, Black, Orange) resistor should be used. Make sure that pin A0 is used, and the circuit is powered to 5V and grounded.z
    Figure 27: Arduino TMP 36 Circuit
  3. There are missing components in the code. Read through the comments and insert code where necessary. After the program is completed, click Start Simulation and open the Serial Monitor to check if the readings are correct.
  4. Clicking the TMP sensor shows a slider for the temperature of the “surroundings” in degrees Celsius.
  5. The Serial Monitor reading is in Fahrenheit, comment out the line for converting Celsius to Fahrenheit (type // before the line that has the conversion) and check that your Serial Monitor reading matches the number on the slider (please be aware that a small error ± 1°C is expected).
  6. The TMP 36 sensor should take a temperature reading every 5 seconds. The analog voltage value read through pin A0 should then be converted to degrees Fahrenheit. The temperature reading should be printed to the Serial Monitor along with the seconds timestamp of the reading.

6. Data Analysis

  1. Open the Lab 5 datasheet.
  2. Since this lab is performed virtually, the competition data for various designs, including pictures, a cost table, and Serial Monitor readings, are provided to you in this spreadsheet. The Lab TA will assign you a group number.
  3. Complete the data analysis for the assigned group number as though the program written in Prototyping a Thermal Insulation Device collected the data for the experiment.
  4. The data pasted from the Serial Monitor into Excel is not correctly separated into columns. To present the data in the correct format, highlight all the data, and go to Data > Text to Columns > Delimited and check off Comma.
  5. Click Finish to see the data in the correct columns.
  6. Create a graph using the X, Y Scatter template. The template is in the Insert tab, under the Charts group with the Scatter icon. Click on the arrow below the icon and select the top left icon in the pull-down gallery.
  7. Correctly scale the axes by clicking on the axis. Select the labels and titles by clicking on the chart, which will change the ribbon to the Design tab. In the Charts Layout group, click the icon that looks like the desired chart. Right click on the elements to be changed.
  8. For the temperature data, name the x-axis Time, and name the y-axis Temperature.
  9. Plot it in half minute intervals for 15 minutes, starting from where the temperature readings stop increasing (that is where the temperature is changing from room temperature to the temperature of the wax). When finished, the graph should look similar to Figure 28.
    Figure 28: Temperature vs. Time Graph of the Thermal Insulation Device
  10. To add a trendline to the graph, click on the Chart Design tab.
  11. On the Chart Design tab, click Add Chart Element and then click Trendline > More Trendline Options.
  12. In the Format Trendline window, select the option of Display Equation on chart. Place the equation correctly on the graph.
  13. The slope of the graph is the insulating capacity (IC) of the design. Record the IC value.
  14. Give the IC, final temperature, and the total cost to the TA. The TA will enter the design's performance into the competition scoresheet and calculate the MDR.
  15. Disregard the rankings. Since the data is given to you, the rankings should be compared to see which designs worked better or worse for the competition and what to discuss in the analysis section of your lab report.

7. Extra Credit: Build a Thermal Insulating Device

  1. For optional extra credit, design a thermal insulation container from household materials using the steps below.
  2. Preferably, materials from Table 4 should be used so that a price can be easily estimated, but it is not necessary. If you have something similar to the materials in Table 4, such as paper towels rather than wool fabric, be creative, and use it.
  3. Analyze the materials and consider the design options, keeping in mind the specifications of this lab.
  4. Sketch the design. Label the drawings clearly including the materials used.
  5. Prepare a cost table and write down the total cost for the thermal insulating device based on the materials chosen.
  6. If a material used is not in Table 4, approximate the price of the material based on the pricing of the rest of the materials (the exact number used is not important). It can be approximate but not outlandish, such as 2 cents for a glass mug, or $1,000 for a piece of toilet paper.
  7. Build the insulating device based on the completed sketch.
  8. Take pictures of the labeled sketch, cost table, and the device prototype.
  9. Include the above pictures in the lab report. Give a brief explanation of why the design would be successful (based on conclusions drawn from comparisons with lab designs) in the lab report.

The lab work is now complete. Refer to the Assignment section for the instructions to prepare the lab report.


Assignment

Individual Lab Report

Follow the lab report guidelines laid out in the EG1004 Writing Style Guide in the Technical Writing section of the manual. Use the outline below to write this report.

  • Describe the basics of Arduino and its application
  • Define electricity and explain electrical components used in your design (i.e. resistor, capacitor, etc.)
  • Explain heat, heat transfer, and all the mechanisms that perform heat transfer. Discuss which of these mechanisms applied to the design
  • Define thermal insulation and the different types of thermodynamic systems
  • Discuss minimal design and its importance
  • Describe the container's design. Explain the choices made. Include a discussion of the materials chosen and why. Talk about the strategy for winning the competition. Include pictures
  • What changes would have increased/decreased the MDR or IC?
  • How was the IC value derived?
  • Describe the design of the TMP 36 circuit
  • Should the Temperature vs. Time graph be smooth or should it have spikes? Explain how closely the curve approximates the ideal and what would affect the data recorded
  • Describe how the design succeeded or failed. Discuss design improvements
  • Include the spreadsheet with the competition results. Describe the results and talk about other designs in the class

Note: It is not unusual to experience instrumentation errors in this lab, leading to incorrect temperatures being recorded. Be sure to read How to Handle Unusual Data in the manual to learn how to handle this.

Remember: Lab notes must be taken. Experimental details are easily forgotten unless written down. EG1004 Lab Notes paper can be downloaded and printed from the EG1004 Website. Use the lab notes to write the Procedure section of the lab report. At the end of each lab, a TA will scan the lab notes and upload them to the Lab Documents section of the EG1004 Website. One point of extra credit is awarded if the lab notes are attached at the end of the lab report. Keeping careful notes is an essential component of all scientific practice.

Team PowerPoint Presentation

Follow the presentation guidelines laid out in the EG1004 Lab Presentation Format in the Technical Presentations section of the manual. When preparing the presentation, consider the following points.

  • What is the importance of prototyping and using Arduino?
  • What is the importance of minimal design?
  • What is the importance of materials in prototyping?
  • Why is it important to minimize heat loss?
  • How can the design be improved?

References

There were no references used.