Difference between revisions of "Mindstorms Programming Exercise Prelab"

From EG1004 Lab Manual
Jump to: navigation, search
Line 13: Line 13:
<p>This program will run motors A and B, reversing motor A after 4 seconds.
<p>This program will run motors A and B, reversing motor A after 4 seconds.
Then, it will stop motors A and B when touch sensor 2 is released.</p>
Then, it will stop motors A and B when touch sensor 2 is released.</p>
<p><b>Important:</b> <i>Touch sensor 1 means the input modifier (found in the
modifiers section of the function palette) for the sensor is Port 1</i></p>


<h3>Program B</h3>
<h3>Program B</h3>
Line 21: Line 18:
<p>This program will run motor A while touch sensor 3 is released.  When touch
<p>This program will run motor A while touch sensor 3 is released.  When touch
sensor 3 is pressed, motor A will reverse for 2 seconds and stop.</p>
sensor 3 is pressed, motor A will reverse for 2 seconds and stop.</p>
<p><b>Important:</b> <i>Touch sensor 1 means the input modifier (found in the
modifiers section of the function palette) for the sensor is Port 1</i></p>


<h3>Program C</h3>
<h3>Program C</h3>
Line 30: Line 24:
light sensor 2 is greater than 35, it will reverse motor A for 6 seconds and
light sensor 2 is greater than 35, it will reverse motor A for 6 seconds and
then stop the motor.</p>
then stop the motor.</p>
<p><b>Important:</b>  <i>Touch sensor 1 means the input modifier (found in the
modifiers section of the function palette) for the sensor is Port 1</i></p>


<h3>Program D</h3>
<h3>Program D</h3>
Line 39: Line 30:
and then reverse motor A for 3 seconds when touch sensor 3 is pressed.  This
and then reverse motor A for 3 seconds when touch sensor 3 is pressed.  This
program should continually check the sensor’s state by jumping to the beginning.</p>
program should continually check the sensor’s state by jumping to the beginning.</p>
<p><b>Important:</b>  <i>Touch sensor 1 means the input modifier (found in the
modifiers section of the function palette) for the sensor is Port 1</i></p>


<h3>Program E</h3>
<h3>Program E</h3>
Line 47: Line 35:
<p>This program will run motors A and B until touch sensor 3 is touched, and then
<p>This program will run motors A and B until touch sensor 3 is touched, and then
will reverse the motor for 3 seconds and then all motors stop.</p>
will reverse the motor for 3 seconds and then all motors stop.</p>
<p><b>Important:</b>  <i>Touch sensor 1 means the input modifier (found in the
modifiers section of the function palette) for the sensor is Port 1</i></p>


<h3>Program F</h3>
<h3>Program F</h3>
Line 56: Line 41:
than 40 and then reverse motor A for 3 seconds when light sensor 3 is less than 40.
than 40 and then reverse motor A for 3 seconds when light sensor 3 is less than 40.
This program should continually check the sensor’s state by jumping to the beginning.</p>
This program should continually check the sensor’s state by jumping to the beginning.</p>
<p><b>Important:</b>  <i>Touch sensor 1 means the input modifier (found in the
modifiers section of the function palette) for the sensor is Port 1</i></p>


<h3>Program G</h3>
<h3>Program G</h3>
Line 64: Line 46:
<p>This program will run motors A and B and wait for light sensor 3 to be less than
<p>This program will run motors A and B and wait for light sensor 3 to be less than
25. Then, the program will reverse motor B for 3 seconds and then all motors stop.</p>
25. Then, the program will reverse motor B for 3 seconds and then all motors stop.</p>
<p><b>Important:</b>  <i>Touch sensor 1 means the input modifier (found in the
modifiers section of the function palette) for the sensor is Port 1</i></p>


<h3>Program H</h3>
<h3>Program H</h3>
Line 80: Line 59:
be released, and continually run this set of operations by jumping to the beginning
be released, and continually run this set of operations by jumping to the beginning
of the program.</p>
of the program.</p>
<p><b>Important:</b>  <i>Touch sensor 1 means the input modifier (found in the
modifiers section of the function palette) for the sensor is Port 1</i></p>


[[Main_Page | Return to Table of Contents]]
[[Main_Page | Return to Table of Contents]]

Revision as of 14:34, 17 October 2007

Mindstorms Programming Exercise

Print and hand in this exercise at the beginning of the Sensors Lab. It will count as the quiz for the Sensors Lab

This assignment will introduce you to the fundamentals of Mindstorms programming. Each student will be assigned a programming task by their TA. You will write a program in Mindstorms that uses sensors to complete the task assigned to you.

Program A

This program will run motors A and B, reversing motor A after 4 seconds. Then, it will stop motors A and B when touch sensor 2 is released.

Program B

This program will run motor A while touch sensor 3 is released.  When touch sensor 3 is pressed, motor A will reverse for 2 seconds and stop.

Program C

This program will run motor A when light sensor 2 is less than 35. When light sensor 2 is greater than 35, it will reverse motor A for 6 seconds and then stop the motor.

Program D

This program will run motor A after 3 seconds when touch sensor 3 is released and then reverse motor A for 3 seconds when touch sensor 3 is pressed.  This program should continually check the sensor’s state by jumping to the beginning.

Program E

This program will run motors A and B until touch sensor 3 is touched, and then will reverse the motor for 3 seconds and then all motors stop.

Program F

This program will run motor A after 3 seconds when light sensor 3 is greater than 40 and then reverse motor A for 3 seconds when light sensor 3 is less than 40. This program should continually check the sensor’s state by jumping to the beginning.

Program G

This program will run motors A and B and wait for light sensor 3 to be less than 25. Then, the program will reverse motor B for 3 seconds and then all motors stop.

Program H

This program will wait for 4 seconds and run motor B. Then, it will reverse motor B when the distance of ultrasonic sensor 3 is less then 10 cm or run motor A for 1 second when the distance of ultrasonic sensor 3 is greater then 50 cm.

Program I

This program will run motor A for 3 seconds, and then wait for touch sensor 2 to be pushed.  Then, it will reverse motor A.  Then it will wait for touch sensor 2 to be released, and continually run this set of operations by jumping to the beginning of the program.

Return to Table of Contents