Difference between revisions of "Digital Logic"

From EG1003 Lab Manual
Jump to: navigation, search
 
(37 intermediate revisions by 4 users not shown)
Line 1: Line 1:
= NI ELVIS Tutorial Video =
<!--= NI ELVIS Tutorial Video =
General Engineering has created a video that discusses breadboard wiring and digital logic circuits: [https://stream.nyu.edu/media/EG+1003+Lab+5A+NI+ELVIS+Tutorial/1_36717xpx NI ELVIS Tutorial Video]. This video provides information on the educational NI-ELVIS II + prototyping board that will aid in designing and wiring the physical circuit. <span style="color: red;"> '''Material covered in the video will be on the Lab 7 quiz. Viewing the video is a mandatory pre-lab assignment. ''' </span>
General Engineering has created a video that discusses breadboard wiring and digital logic circuits: [https://stream.nyu.edu/media/EG+1003+Lab+5A+NI+ELVIS+Tutorial/1_36717xpx NI ELVIS Tutorial Video]. This video provides information on the educational NI-ELVIS II + prototyping board that will aid in designing and wiring the physical circuit. <span style="color: red;"> '''Material covered in the video will be on the Lab 8 quiz. Viewing the video is a mandatory pre-lab assignment. ''' </span>-->
= Objective =


= Objectives =
The experimental objective of this lab is to design a combinational logic circuit for a given problem statement, and to activate it under specific conditions and test it using LabVIEW. After testing, it will be built on an NI-ELVIS II+ prototyping board.
The experimental objective of this lab is to design a combinational logic circuit that will activate under specific conditions and test it using LabVIEW. After testing, it will be built on an NI-ELVIS II+ prototyping board.


= Overview =
= Overview =
The first step in understanding the digital circuits that control the function of electronic devices is the mastery of Boolean logic. George Boole, an English mathematician, established modern symbolic logic in 1854 with the publication of his paper, "Laws of Thought." Boolean logic is the foundation of digital circuitry. Boole's method of logical inference allows conclusions to be drawn from any proposition involving any number of terms. Boolean logic demonstrates that the conclusions found are logically contained in the original premises.<ref name="one">''Boole, George'', Encyclopedia Britannica, 2003. Encyclopedia Britannica Online. Retrieved July 29<sup>th</sup>, 2003 ''[http://www.britannica.com/eb/article?eu=82823 http://www.britannica.com/eb/article?eu=82823]''</ref>


In Boolean logic, there are only two values, true and false, represented by the numbers 1 and 0, respectively. These values are combined in equations to yield results that also have these two values. The equations are represented by truth tables that show the inputs to the equation and the outputs produced for those inputs. The rows of the table contain all the possible combinations of 1s and 0s for the inputs. The number of rows is determined by the number of possible combinations.
The first step in understanding the digital circuits that control the function of electronic devices is the mastery of <b>Boolean logic</b>. George Boole, an English mathematician, established modern symbolic logic in 1854 with the publication of his paper, "Laws of Thought." Boolean logic is the foundation of digital circuitry. Boole's method of logical inference allows conclusions to be drawn from any proposition involving any number of terms. Boolean logic demonstrates that the conclusions found are logically contained in the original premises (Encyclopedia Britannica, 2003).


Boolean logic is applied to digital circuitry through the use of simple logic gates. There are symbols for each of these gates, and the connections between them are represented by lines running from the output of one gate to the input of the other. A line can connect only one output to each input. There are seven of these gates: the NOT, AND, OR, NAND, NOR, XOR, and XNOR gates. Only the first three will be used in this lab.
== Truth Tables ==


The NOT gate is the simplest of these three. It is an inverter. It has one input and produces its opposite as output. The symbol for a NOT gate is shown in Figure 1.
In Boolean logic, there are only two values, true and false, represented by the numbers 1 and 0, respectively. These values are combined in equations to yield results that also have these two values. The equations are represented by <b>truth tables</b> that show the inputs to the equation and the outputs produced for those inputs. The rows of the table contain all the possible combinations of 1s and 0s for the inputs. The number of rows is determined by the number of possible combinations.


[[Image:lab_logic_1.jpg|frame|center| Figure 1: NOT gate symbol.]]
To illustrate a truth table and additional concepts that will be introduced, an example problem statement will be given. Think of an ATM that has three options: print a statement, withdraw money, or deposit money. The ATM will charge a fee to (1) withdraw money or (2) print a statement without depositing money. The intent of the problem is to develop a Boolean equation and logic circuit that will determine after which possible combination of actions will someone get charged a fee. First, a truth table should be made for all the possible combinations of inputs. The inputs are the ATM's three functions. Let variable <math>P</math> stand for printing a statement, <math>W</math> for withdrawing money, and <math>D</math> for depositing money. There is one output, which is whether or not the ATM will charge a fee. The output will be denoted by <math>C</math>. The truth table in Table 1 shows all the possible combinations of the inputs and their corresponding outputs.


<center>
Table 1: Truth Table for the ATM Example
{| class="truthtable"
|-
!colspan="3"|Inputs!!Output
|-
!<math>P</math>!!<math>W</math>!!<math>D</math>!!<math>C</math>
|-
|0||0||0||0
|-
|0||0||1||0
|-
|0||1||0||1
|-
|0||1||1||1
|-
|1||0||0||1
|-
|1||0||1||0
|-
|1||1||0||1
|-
|1||1||1||1
|-
|}
</center>
== Logic Gates ==
Boolean logic is applied to digital circuitry through the use of simple <b>logic gates</b>. There are symbols for each of these gates, and the connections between them are represented by lines running from the output of one gate to the input of another. A line can connect only one output to each input. There are seven of these gates: the NOT, AND, OR, NAND, NOR, XOR, and XNOR gates. Only the first three will be used in this lab (Figure 1).
[[Image:Lab 8 Figure 1.jpg|frame|center| Figure 1: Logic Gate Symbols]]


The truth table for a NOT gate has one input, or A in this example, and one output. The symbol for the operation is a horizontal bar over the variable. The truth table for a NOT gate is shown in Table 1.
The <b>NOT gate</b> is the simplest of these three. It is an inverter. It has one input and produces its opposite as the output. For example, if a 1 value is put into a NOT gate, a 0 value is outputted, as seen in Table 2. The symbol for the operation is a horizontal bar over the variable. The truth table for a NOT gate is shown in Table 2.


<center> Table 2: Truth Table for a NOT Gate
{| class="truthtable"
{| class="truthtable"
|-
|-
Line 28: Line 60:
|-
|-
|}
|}
</center>


The AND gate performs a multiplication operation on its inputs. If all the inputs are true, the output is also true. But if either of the inputs is false, the output is also false. An AND gate can have two or more inputs, but for this lab, it will have two inputs. The symbol for an AND gate is shown in Figure 2.
The <b>AND gate</b> performs a multiplication operation on its inputs. If all the inputs are true, the output is also true. But if either of the inputs is false, the output is also false. An AND gate can have two or more inputs, but for this lab, it will have two inputs (denoted by A and B in Table 3). The symbol for the AND operation is a dot (·) or the two inputs one after the other with nothing between them. The truth table for an AND gate is shown in Table 3.
 
[[Image:lab_logic_4.jpg|frame|center| Figure 2: AND gate symbol.]]
 
This gate has two inputs, or A and B in this example, and one output. The symbol for the AND operation is a dot (·) or the two inputs one after the other with nothing between them. The truth table for an AND gate is shown in Table 2.


<center>Table 3: Truth Table for an AND Gate
{| class="truthtable"
{| class="truthtable"
|-
|-
Line 48: Line 78:
|-
|-
|}
|}
</center>


An OR gate performs an addition operation on its inputs. If either of the inputs is true, the output is also true. But if all the inputs are false, the output is also false. An OR gate can have two or more inputs, but for this lab, it will have two inputs. The symbol for an OR gate is shown in Figure 3.
An <b>OR gate</b> performs an addition operation on its inputs. If either of the inputs is true, the output is also true. But if all the inputs are false, the output is also false. An OR gate can have two or more inputs, but for this lab, it will have two inputs (denoted by A and B in Table 4). The symbol for the OR operation is a plus (+). The truth table for an OR gate is shown in Table 4.
 
[[Image:lab_logic_7.jpg|frame|center| Figure 3: OR gate symbol.]]
 
An OR gate has two inputs, or A and B in this example, and one output. The symbol for the OR operation is a plus (+). The truth table for an OR gate is shown in Table 3.


<center>Table 4: Truth Table for an OR Gate
{| class="truthtable"
{| class="truthtable"
|-
|-
Line 68: Line 96:
|-
|-
|}
|}
</center>
== Boolean Equations ==
A truth table is used to write a <b>Boolean equation</b> for a problem. All the combinations that yield an output of 1 are kept, and the equation is written. This is called a Sum of Products solution. Only the combinations that yield an output of 1 are kept because the Boolean equation intends to represent a quantitative function for when the result will have a value of true (when a fee is charged in the example of the ATM machine). The combinations that yield an output of 0 are essentially discarded because there is no interest in when the result has a false value. The Boolean equation for the ATM example can be seen in Figure 2.


The truth table attached to each of these gates indicates when the gate will return a value of true. These tables are used to write a Boolean equation for a problem. All the combinations that yield an output of 1 are kept, and the equation is written. This is called a Sum of Products solution.
<center><math>C = \overline{P} W \overline{D} + \overline{P} W D + P \overline{W}\,\overline{D} + P W \overline{D} + P W D\,</math><br>
Figure 2: Boolean Equation</center><br>


A truth table showing every possible combination of inputs and their corresponding outputs yields a Boolean equation that is the solution to a problem in digital logic. This equation can be simplified using a Karnaugh map (K-map). A K-map identifies and eliminates all the conditions that do not contribute to the solution. This simplified equation is used to build the digital circuit and will be a combination of the gates described above.
For each of the combinations (rows) resulting in true in Table 1, the terms of the Boolean equation are determined by multiplying the variables together (the AND operation). If an input is true, the variable can be used as is; for an input that is false, the variable is inverted using the horizontal bar (the NOT operation). Since the output is true if any of the combinations are true, the equation is formed by using addition operations (the OR operation) on all the terms formed by the product of each combination.


A K-map is a two-dimensional representation of the truth table that shows the common characteristics of the inputs. For an equation with three inputs, usually all the combinations of the first two inputs are shown as four columns and the values for the third input are shown as two rows. For four inputs, all the combinations of the third and fourth inputs are shown as four rows. Only one value can change at a time in adjacent rows or columns. For example, in the truth table in Table 4, A, B, and C are the inputs and D is the output.
== Karnaugh Maps (K-Maps) ==


{| class="truthtable"
A truth table showing every possible combination of inputs and their corresponding outputs yields a Boolean equation that is the solution to a problem in digital logic. However, this equation can be simplified using a <b>Karnaugh map (K-map)</b>. A K-map identifies and eliminates all the conditions that do not contribute to the solution. The resulting simplified Boolean equation is used to build the digital circuit and will be a combination of the logic gates described above.
|-
!<math>A\,</math>!!<math>B\,</math>!!<math>C\,</math>!!<math>D\,</math>
|-
|0||0||0||0
|-
|0||0||1||1
|-
|0||1||0||0
|-
|0||1||1||1
|-
|1||0||0||0
|-
|1||0||1||1
|-
|1||1||0||1
|-
|1||1||1||1
|-
|}


This table looks complex, but it can be simplified with a K-map (Table 5).
A K-map is a two-dimensional representation of the truth table that shows the common characteristics of the inputs. For an equation with three inputs, usually all the combinations of the first two inputs are shown as four columns and the values for the third input are shown as two rows. For four inputs, all the combinations of the third and fourth inputs are shown as four rows. Only one value can change at a time in adjacent rows or columns. For example, in Table 5, the columns change from 00 to 01 to 11 to 10. Table 5 illustrates the K-map for the ATM example.


<center> Table 5: K-Map for the ATM Example
{| class="kmap"
{| class="kmap"
|-
|-
!!!!!0 0!!0 1!!1 1!!1 0
!!!!!0 0!!0 1!!1 1!!1 0
|-
|-
!!!!!<math>\overline{A} \, \overline{B}\,</math>!!<math>\overline{A} B</math>!!<math>A B\,</math>!!<math>A \overline{B}</math>
!!!!!<math>\overline{P} \, \overline{W}\,</math>!!<math>\overline{P} W</math>!!<math>P W\,</math>!!<math>P \overline{W}</math>
|-
|-
!0!!<math>\overline{C}\,</math>
!0!!<math>\overline{D}\,</math>
|0||0||1||0
|0||1||1||1
|-
|-
!1!!<math>C\,</math>
!1!!<math>D\,</math>
|1||1||1||1
|0||1||1||0
|-
|-
|}
|}
</center>
== Simplified Boolean Equations ==
To develop the <b>simplified Boolean equation</b>, look for the cells that have the 1 value in common. Look for cells that can physically be boxed together, where the number of cells in the box is a power of 2 (1, 2, 4, or 8 and so on). The boxes are allowed to overlap so the same cells can be used more than once. Look for the biggest boxes first, and keep finding smaller boxes until all the cells with a 1 in them are used. This means that sometimes just single cells will remain at the end. The cells in the K-map for the ATM example can be grouped like what is shown in Figure 3.


Look for the cells that have values in common. For example, the entire bottom row has ones in all its cells. This means that any time C is true, the output is true. This can be done in a more organized manner. Look for cells that form rectangles, where the number of cells in the rectangle is a power of 2: 1, 2, 4, or 8 and so on. The bottom row is an example of this. There is another small rectangle of two cells in the column with 1 1 at the top. This means that the output is true whenever A and B are true. The rectangles are allowed to overlap so the same cells can be used more than once, which happened here. Look for the biggest rectangles first, and keep finding smaller rectangles until all the cells with a 1 in them are used. This means that sometimes just single cells will remain at the end. In this example, all the cells containing a 1 were covered with two rectangles. This means is that if the conditions for either rectangle are true, the output will be true. Looking at the row and column labels, the bottom row is C, and for the column, the header is AB. This yields the simplified Boolean equation shown in Figure 4.
[[Image:Kmap_Boxes.gif|250px|center]]
<center>Figure 3: K-Map Boxes for the ATM Example</center><br>


<math>D = AB + C\,</math>
In this example, all the cells containing a 1 were covered with two boxes. This means is that if the conditions for either box are true, the output will be true. This also means that the simplified Boolean equation will only have two terms. The term for each box can be determined by observing which variables are constant throughout each cell of that box. For the red box, only <math>W</math> remains constant through the four cells. <math>D</math> switches from the top row to the bottom row, and <math>P</math> switches from the left column to the right column. For the blue box, <math>P</math> and <math>\overline{D}</math> remains constant through the two cells, while <math>W</math> switches from the left cell to the right cell. The two boxes yield the simplified Boolean equation shown in Figure 4.


Figure 4: Simplified Boolean Equation
<center><math>C = W + P\overline{D}\,</math></center>
<center>Figure 4: Simplified Boolean Equation for the ATM Example</center><br>


This equation meets the conditions in the truth table and achieves the desired result with the minimum number of logic elements.
This equation meets the conditions in the truth table in Table 1 and achieves the desired result with the minimum number of logic elements.
 
== Combinational Logic Circuits ==
 
Lastly, a <b>combinational logic circuit</b> can be created using the simplified equation. First, a NOT operation is performed on <math>D</math> by inputting and outputting <math>D</math> through a NOT gate. Then, the <math>P</math> and inverted <math>D</math> are inputted into an AND gate, as denoted by them being multiplied in Figure 4. Finally, the result of the AND operation between the <math>P</math> and inverted <math>D</math> and the <math>W</math> are inputted into an OR gate, as denoted by the addition function in Figure 4. The final combinational logic circuit can be seen in Figure 5.
 
[[Image:lab_logic_16.gif|frame|center|Figure 5: Combinational Logic Circuit for the ATM Example]]


= Materials and Equipment =
= Materials and Equipment =
* A 7432 IC (4 dual-input OR gates)
* A 7432 IC (4 dual-input OR gates)
* A 7408 IC (4 dual-input AND gates)
* A 7408 IC (4 dual-input AND gates)
* A 7404 IC (6 single input NOT gates)
* A 7404 IC (6 single-input NOT gates)
* A lab PC with LabVIEW software
* A lab PC with LabVIEW 2019 software
* An NI-ELVIS II+ with prototyping board
* An NI-ELVIS II+ with prototyping board
* Wiring
* Electrical leads
 
<!--
= Sample Problem =
= Sample Problem =
An ATM has three options: print a statement, withdraw money, or deposit money. The ATM will charge a $1 fee to:
An ATM has three options: print a statement, withdraw money, or deposit money. The ATM will charge a $1 fee to:
Line 196: Line 225:


[[Image:Kmap_Boxes.gif|thumb|250px|frame|left|Table 8: K-map with boxes]]
[[Image:Kmap_Boxes.gif|thumb|250px|frame|left|Table 8: K-map with boxes]]


Always try to group the greatest number of common values in powers of 2.
Always try to group the greatest number of common values in powers of 2.
Line 225: Line 242:


[[Image:lab_logic_16.gif|frame|center|Figure 7: Combinational logic circuit diagram for the simplified equation.]]
[[Image:lab_logic_16.gif|frame|center|Figure 7: Combinational logic circuit diagram for the simplified equation.]]
-->
= Problem Statement =


= Problem Statement =
Farmer Georgi owns a 350-acre dairy farm in upstate New York. In addition to milk and butter, Farmer Georgi sells fresh eggs at the Union Square Greenmarket in Manhattan. It is imperative that Farmer Georgi protects the hen that produces eggs for his business.
A farmer owns a 350-acre dairy farm in upstate New York. In addition to milk and butter, the farmer sells fresh eggs at the Union Square Greenmarket in Manhattan. It is imperative that the farmer protect the hen that lays his eggs.


He has two barns, one hen, and a supply of corn. A fox has been attempting to eat the hen by hiding in a barn. The hen can move freely from one barn to the other. Farmer Georgi sometimes stores corn in one barn and sometimes in the other, but he never stores it in both at the same time. The hen would like to eat the corn and the fox would like to eat the hen. Farmer Georgi needs an alarm system that uses digital logic circuits to protect the hen and the corn. The design should use the fewest gates and input variables possible. The alarm will sound if:
Farmer Georgi has two barns, one hen, and a supply of corn. A fox has been attempting to eat the hen by hiding in a barn. The hen can move freely from one barn to the other. Farmer Georgi sometimes stores corn in one barn and sometimes in the other, but he never stores it in both at the same time. The hen would like to eat the corn and the fox would like to eat the hen. Farmer Georgi needs an alarm system that uses digital logic circuits to protect the hen and the corn. The design should use the fewest logic gates and input variables possible. The alarm will sound if:


# The fox and the hen are in the same barn
# The fox and the hen are in the same barn
Line 236: Line 254:
= Procedure =
= Procedure =


<span style="color: red;">'''''Prior to Beginning the Procedure'''''</span>
== 1. Test the Integrated Circuits (ICs) ==


Before performing the lab, the integrated circuits (IC) used must be tested to determine if they are functioning. If the procedure is completed without verifying that the ICs work, problems may occur in the circuit that require additional time and troubleshooting. The system for checking the ICs uses an Arduino to send and receive signals from the AND/OR/NOT chips and determines if they are functioning properly.
Before performing the lab, the integrated circuits (IC) used in wiring the alarm system on the NI-ELVIS board must be tested to determine if they are functioning. If the procedure is completed without verifying that the ICs work, problems may occur in the circuit that require additional time and troubleshooting. The system for checking the ICs uses an Arduino board to send and receive signals from the AND/OR/NOT chips and determines if they are functioning properly.


First, load the chip onto the IC tester (Figure 8) and start the Serial Monitor on the Arduino program. The code will cycle through the basic inputs (0, 1 for NOT; 00, 01, 10, 11 for AND/OR) and then send the outputs of each gate within the chip back into the Arduino. The code compares those results to the expected result. It displays each input/output pair and displays the final result showing if the chip is functional or defective. The goal is to determine if the gates are outputting the correct results. '''''Remove the chip carefully from the IC tester.'''''
First, load the chip onto the Arduino board (Figure 6) and start the Serial Monitor on the Arduino program. The code will cycle through the basic inputs (0, 1 for NOT; 00, 01, 10, 11 for AND/OR) and then send the outputs of each gate in the chip back to the Arduino board. The code compares those results to the expected result. It displays each input/output pair and displays the final result indicating if the chip is functional or defective. The goal is to determine if the gates are outputting the correct results. <b>After, remove the chips carefully from the Arduino board.</b>


[[Image:IC_Tester.JPG|thumb|500px|center| Figure 8: IC Tester.]]
[[Image:IC_Tester.JPG|thumb|500px|center|Figure 6: IC Testing Setup]]


'''''Problem Statement Procedure'''''
== 2. Procedure ==


Note: The two barns must be assigned a numeric equivalent before the truth table is prepared for Step 1. Use 1 for Barn 1 and 0 for Barn 2. For the alarm output, use 0 to indicate the alarm should be off, and 1 to indicate that the alarm should be on.
# The two barns must be assigned a numeric equivalent before the truth table is prepared. Use 1 for Barn 1 and 0 for Barn 2 (1 does not mean true and 0 does not mean false for the inputs). For the alarm output, use 0 to indicate that the alarm should be off, and 1 to indicate that the alarm should be on.
# On a sheet of lined lab note paper from the [http://eg.poly.edu/downloads/Note_paper.zip EG Website], create a truth table that includes three inputs and one output. Assign the input variables. Include all possible scenarios for the hen, the corn, and the fox.
# On a sheet of Lab Notes paper provided by the TAs, create a truth table that includes the three inputs and one output. Assign the input variables. Include all possible scenarios for the hen, the corn, and the fox.
# Compute the output column. To do this, analyze the three inputs and determine if the alarm will sound in each scenario. Place a 1 in the output column if the alarm will sound and a 0 if it will not.
# Compute the output column. To do this, analyze the three inputs and logically determine if the alarm will sound in each scenario. Place a 1 in the output column if the alarm will sound and a 0 if it will not.  
# Note all the combinations that produce a 1 in the output column.
# Note all the combinations that produce a 1 in the output column. Create a Boolean equation from this table that includes each of the inputs that produced a true output.
# Create a Boolean equation from this table that includes each of the inputs that produced a true output.
# Create a K-map. Draw a map that lists all the possible combinations from the Boolean equation. Use the Boolean equation to fill in the 1s and 0s on the K-map.
# Create a K-map. Draw a map that lists all the possible combinations. Use the Boolean equation to fill in the 1s on the K-map.
# Box the pairs of 1s appropriately. The 1s may only be boxed in powers of 2 starting with the largest possible combination and working down to the smallest. The outcomes that do not contribute to the solution are to be discarded.
# Circle the pairs of 1s. The 1s may only be circled in powers of 2 starting with the largest possible combination and working down to the smallest. The outcomes that do not contribute to the solution are discarded.
# This process yields a simplified Boolean equation. Write this simplified Boolean equation down.
# This process yields a simplified Boolean equation. Write this simplified equation down.
# Draw a combinational logic circuit of the simplified Boolean equation.
# Draw a schematic diagram of the simplified Boolean equation.
# Have a TA approve the steps to obtain the combinational logic circuit for accuracy.
# Have a TA sign the diagram.
# Build the logic circuit in LabVIEW 2019 using the combinational logic circuit that was drawn. Open LabVIEW and select New VI. Go to Window > Tile Left and Right.
# Test the circuit diagram. Build the circuit in LabVIEW. Use the simplified Boolean equation. Open LabVIEW and select New VI. Pull down the Window menu, select Tile Left and Right.
# Place three switches on the front panel that represent the hen, the corn, and the fox. Place a Boolean indicator on the front panel to represent the output.
# Place three switches on the front panel that represent the hen, the corn, and the fox. Place one Boolean indicator on the front panel to represent the output.
# Go to the Functions palette > Modern tab > Programming > Boolean and select the AND, NOT, and OR gates necessary for the circuit.
# Open the Functions palette. Under Programming, select Boolean and choose the AND, NOT, and OR gates necessary for the circuit. A TA will assist in this process.
# Once the LabVIEW program is complete, have a TA check and approve the circuit.
# Once the LabVIEW program is complete, have a TA check the circuit.
# Build the circuit on a NI-ELVIS II+ prototyping board. On the board, identify each of the three IC chips as an AND, OR, or NOT gate. To do this, read the number on the chip and match it with the numbers shown in Figure 7. Look for the notch at one end of each chip to orient the chip to the diagrams in Figure 7 and to match the pins.  
# Build the circuit on a prototyping board.
#: [[Image:lab_logic_17.jpg|frame|center|Figure 7: IC Numbers and Pins]]
# On the board, identify each of the three black chips as an AND, OR, or NOT gate. To do this, read the number on the chip and match it with the list in the [[#Materials and Equipment|Materials and Equipment]] section of this lab. Use the pinouts in Figure 9 to wire the gates. Look for the notch at one end of each chip to orient the chip to diagrams in Figure 9 to match the pinouts.
# Place the IC chips over the bridge in the NI-ELVIS board (Figure 8).
#: [[Image:lab_logic_17.jpg|frame|center|Figure 9: IC Pinouts.]]
#: [[Image:IC Chip in Breadboard.jpg|250px|thumb|center|Figure 8: IC Chip in Breadboard]]
# Power the chips. Insert one end of the wire into a hole on Row 54 (marked +5V) of the side breadboards. Insert the other end of the wire into the hole on the breadboard nearest Pin 14 on the chip. Repeat this process for all three chips.
# Power the chips. Insert one end of an electrical lead into Row 54 (marked +5V) of the NI-ELVIS board. Insert the other end of the lead into Pin 14 of the IC chip. Repeat this process for all three chips.
#: [[Image:lab_logic_20.gif|frame|center|Figure 10: Breadboard layout. Wiring diagram, left. Photograph, right.]]
# Ground the chips using the same method. Insert one end of another electrical lead into Row 53 (marked Ground) of the NI-ELVIS board and the other end into Pin 7 of the IC chip. Repeat this process for all three chips.
#: The breadboard is set up in the following manner:
# Look at the top right corner of the breadboard to find the Digital Input/Output (DIO) holes. Select one of the DIO rows to use as one of the input variables and begin wiring the circuit based on the simplified Boolean equation. Assign the other DIO rows for the remaining input variables.
#:# The leftmost and rightmost columns of slots (the ones in between the red and blue lines) are connected vertically.
# Continue this process until the entire circuit is wired. Insert one end of a lead into the final output of the NI-ELVIS circuit. Attach the other end of the lead to any row for an LED on the board.
#:# The rest of the breadboard is connected horizontally, however, there is a break that runs down the center of the breadboard, separating Columns A-E and F-J, as shown in Figure 10.
# Ground the chips using the same method. Insert one end of a wire into a hole on Row 53 (marked Ground) of the small breadboards and the other end into Pin 7 of the chip. Repeat this process for all three chips.
# Look at the top right corner of the breadboard to find the Digital Input/Output (DIO) holes. Select one of the DIO row of holes to use as one of the variables and begin wiring the circuit based on the simplified Boolean equation. Assign the other DIO rows for the remaining variables.
# Continue this process until the entire circuit is wired. Insert one end of the wire into the final output of the simplified Boolean equation. Attach the other end to any hole marked LED on the board.
# Plug in the NI-ELVIS II+ and connect the USB cable to the lab PC.
# Plug in the NI-ELVIS II+ and connect the USB cable to the lab PC.
# Power on the NI-ELVIS II+ by toggling the switch on the back of the device. When the pop-up window appears, select NI-ELVISmx Instrument Launcher and click OK (Figure 11).
# Power on the NI-ELVIS II+ by toggling the switches on the back of the device and top of the device. When the pop-up window appears, select NI-ELVISmx Instrument Launcher and click OK (Figure 9).
#: [[Image:lab_logic_21.png|frame|center|Figure 11: New data acquisition device dialog window.]]
#: [[Image:lab_logic_21.png|300px|thumb|center|Figure 9: New Data Acquisition Device Dialog Window]]
# Click on the DigOut Icon on the Instrument Launcher window (Figure 12).
# Click on the DigOut Icon on the Instrument Launcher window (Figure 10).
#: [[Image:lab_logic_22.png|frame|center|Figure 12: NI ELVISmx Instrument Launcher dialog window.]]
#: [[Image:Lab 8 Figure 10.png|frame|center|Figure 10: NI ELVISmx Instrument Launcher Dialog Window]]
#[[Image:lab_logic_23.png|thumb|200px|right|Figure 13: Digital Writer dialog window.]]Select the appropriate range for the ''Lines to Write'' setting in the Digital Writer dialog window that corresponds to the DIO rows chosen. For example, if fox, hen, and corn are on DIO 21, DIO 22, and DIO 23, select 16&ndash;23.
# The NI ELVISmx Digital Writer window should appear (Figure 11). Select the appropriate range for the Lines to Write corresponding to the DIO rows used in the wiring. For example, if the fox, hen, and corn are wired to DIO 21, 22, and 23, select 16&ndash;23 for the Lines to Write.
# Click ''Run'' and toggle the switches corresponding to fox, hen, and corn.<br clear="both"/>
#: [[Image:lab_logic_23.png|300px|thumb|center|Figure 11: Digital Writer Window]]
# Click Run and toggle the switches corresponding to the fox, hen, and corn. Observe the LED for the alarm light up based on the inputs to each barn.
# Have a TA check the circuit.
# Have a TA check the circuit.


The lab work is now complete. Please clean up the workstation. Return all unused materials to a TA. Refer to '''''[[#Assignment|Assignment]]''''' for the instructions to prepare the lab report.
The lab work is now complete. Please clean up the workstation. Return all unused materials to a TA.


= Assignment =
= Assignment =


== Team Lab Report ==
== Team Lab Report ==
Follow the lab report guidelines laid out in the page called [[Specifications for Writing Your Lab Reports]] in the ''Technical Communication'' section of this manual. The following points should be addressed in the appropriate section of the lab report:
 
* Describe how digital logic impacts the real world
{{Labs:Lab Report}}
* Describe the problem that was solved in the Introduction
 
* Describe the problem statement regarding Farmer Georgi
* Describe how AND, OR, and NOT gates work
* Describe how AND, OR, and NOT gates work
* Include the truth table, Boolean equation, K-map, simplified Boolean equation, and combinational logic circuit developed during the lab
* What is a truth table? How does it contribute to obtaining a Boolean equation?
* What is a truth table? How does it contribute to obtaining a Boolean equation?
* What is a K-map? How does it contribute to obtaining a simplified Boolean equation? To demonstrate the simplification, show what the equation would look like if terms were written for each of the true values and the simplified equation by applying the K-map. Discuss how much simpler the circuitry is as a result of applying the K-map
* What is a K-map? How does it contribute to obtaining a simplified Boolean equation? To demonstrate the simplification, show what the equation would look like if terms were written for each of the true values and the simplified equation by applying the K-map. Discuss how much simpler the circuitry is as a result of applying the K-map
Line 295: Line 312:
* Why is there a need for the minimization of a logic design and what are the advantages?
* Why is there a need for the minimization of a logic design and what are the advantages?
* How does the use of a combinational logic circuit contribute to advances in technology?
* How does the use of a combinational logic circuit contribute to advances in technology?
* Describe the design changes that would be necessary if one of the barns used a bell as an alarm and the other used a horn
* Discuss other possible design/procedural improvements
* Describe how the final combinational logic circuit was obtained
* Describe how the final combinational logic circuit was obtained
* Insert a screenshot of the front and back panels in the report
* Include a screenshot of the front and back panels of the LabVIEW VI


{{Lab notes}}
{{Labs:Lab Notes}}


== Team PowerPoint Presentation ==
== Team PowerPoint Presentation ==
Follow the presentation guidelines laid out in the page called [[EG1003 Lab Presentation Format]] in the ''Introduction to Technical Presentations'' section of this manual. When preparing the presentation, consider the following points:
 
{{Labs:Team Presentation}}
 
* How does digital logic impact the world today?
* How does digital logic impact the world today?
* Look into the future, how will digital logic change the world?
* Looking into the future, how will digital logic change the world?
* Include the truth table, Boolean equation, K-map, simplified Boolean equation, and combinational logic circuit developed during the lab
 
= References =


= Footnotes =
<i>Boole, George</i>, Encyclopedia Britannica, 2003. Encyclopedia Britannica Online. Retrieved July 29, 2003 http://www.britannica.com/eb/article?eu=82823
{{Reflist}}


{{Laboratory Experiments}}
{{Laboratory Experiments}}

Latest revision as of 17:14, 25 April 2020

Objective

The experimental objective of this lab is to design a combinational logic circuit for a given problem statement, and to activate it under specific conditions and test it using LabVIEW. After testing, it will be built on an NI-ELVIS II+ prototyping board.

Overview

The first step in understanding the digital circuits that control the function of electronic devices is the mastery of Boolean logic. George Boole, an English mathematician, established modern symbolic logic in 1854 with the publication of his paper, "Laws of Thought." Boolean logic is the foundation of digital circuitry. Boole's method of logical inference allows conclusions to be drawn from any proposition involving any number of terms. Boolean logic demonstrates that the conclusions found are logically contained in the original premises (Encyclopedia Britannica, 2003).

Truth Tables

In Boolean logic, there are only two values, true and false, represented by the numbers 1 and 0, respectively. These values are combined in equations to yield results that also have these two values. The equations are represented by truth tables that show the inputs to the equation and the outputs produced for those inputs. The rows of the table contain all the possible combinations of 1s and 0s for the inputs. The number of rows is determined by the number of possible combinations.

To illustrate a truth table and additional concepts that will be introduced, an example problem statement will be given. Think of an ATM that has three options: print a statement, withdraw money, or deposit money. The ATM will charge a fee to (1) withdraw money or (2) print a statement without depositing money. The intent of the problem is to develop a Boolean equation and logic circuit that will determine after which possible combination of actions will someone get charged a fee. First, a truth table should be made for all the possible combinations of inputs. The inputs are the ATM's three functions. Let variable stand for printing a statement, for withdrawing money, and for depositing money. There is one output, which is whether or not the ATM will charge a fee. The output will be denoted by . The truth table in Table 1 shows all the possible combinations of the inputs and their corresponding outputs.

Table 1: Truth Table for the ATM Example

Inputs Output
0 0 0 0
0 0 1 0
0 1 0 1
0 1 1 1
1 0 0 1
1 0 1 0
1 1 0 1
1 1 1 1

Logic Gates

Boolean logic is applied to digital circuitry through the use of simple logic gates. There are symbols for each of these gates, and the connections between them are represented by lines running from the output of one gate to the input of another. A line can connect only one output to each input. There are seven of these gates: the NOT, AND, OR, NAND, NOR, XOR, and XNOR gates. Only the first three will be used in this lab (Figure 1).

Figure 1: Logic Gate Symbols

The NOT gate is the simplest of these three. It is an inverter. It has one input and produces its opposite as the output. For example, if a 1 value is put into a NOT gate, a 0 value is outputted, as seen in Table 2. The symbol for the operation is a horizontal bar over the variable. The truth table for a NOT gate is shown in Table 2.

Table 2: Truth Table for a NOT Gate
0 1
1 0

The AND gate performs a multiplication operation on its inputs. If all the inputs are true, the output is also true. But if either of the inputs is false, the output is also false. An AND gate can have two or more inputs, but for this lab, it will have two inputs (denoted by A and B in Table 3). The symbol for the AND operation is a dot (·) or the two inputs one after the other with nothing between them. The truth table for an AND gate is shown in Table 3.

Table 3: Truth Table for an AND Gate
0 0 0
0 1 0
1 0 0
1 1 1

An OR gate performs an addition operation on its inputs. If either of the inputs is true, the output is also true. But if all the inputs are false, the output is also false. An OR gate can have two or more inputs, but for this lab, it will have two inputs (denoted by A and B in Table 4). The symbol for the OR operation is a plus (+). The truth table for an OR gate is shown in Table 4.

Table 4: Truth Table for an OR Gate
0 0 0
0 1 1
1 0 1
1 1 1

Boolean Equations

A truth table is used to write a Boolean equation for a problem. All the combinations that yield an output of 1 are kept, and the equation is written. This is called a Sum of Products solution. Only the combinations that yield an output of 1 are kept because the Boolean equation intends to represent a quantitative function for when the result will have a value of true (when a fee is charged in the example of the ATM machine). The combinations that yield an output of 0 are essentially discarded because there is no interest in when the result has a false value. The Boolean equation for the ATM example can be seen in Figure 2.


Figure 2: Boolean Equation


For each of the combinations (rows) resulting in true in Table 1, the terms of the Boolean equation are determined by multiplying the variables together (the AND operation). If an input is true, the variable can be used as is; for an input that is false, the variable is inverted using the horizontal bar (the NOT operation). Since the output is true if any of the combinations are true, the equation is formed by using addition operations (the OR operation) on all the terms formed by the product of each combination.

Karnaugh Maps (K-Maps)

A truth table showing every possible combination of inputs and their corresponding outputs yields a Boolean equation that is the solution to a problem in digital logic. However, this equation can be simplified using a Karnaugh map (K-map). A K-map identifies and eliminates all the conditions that do not contribute to the solution. The resulting simplified Boolean equation is used to build the digital circuit and will be a combination of the logic gates described above.

A K-map is a two-dimensional representation of the truth table that shows the common characteristics of the inputs. For an equation with three inputs, usually all the combinations of the first two inputs are shown as four columns and the values for the third input are shown as two rows. For four inputs, all the combinations of the third and fourth inputs are shown as four rows. Only one value can change at a time in adjacent rows or columns. For example, in Table 5, the columns change from 00 to 01 to 11 to 10. Table 5 illustrates the K-map for the ATM example.

Table 5: K-Map for the ATM Example
0 0 0 1 1 1 1 0
0 0 1 1 1
1 0 1 1 0

Simplified Boolean Equations

To develop the simplified Boolean equation, look for the cells that have the 1 value in common. Look for cells that can physically be boxed together, where the number of cells in the box is a power of 2 (1, 2, 4, or 8 and so on). The boxes are allowed to overlap so the same cells can be used more than once. Look for the biggest boxes first, and keep finding smaller boxes until all the cells with a 1 in them are used. This means that sometimes just single cells will remain at the end. The cells in the K-map for the ATM example can be grouped like what is shown in Figure 3.

Kmap Boxes.gif
Figure 3: K-Map Boxes for the ATM Example


In this example, all the cells containing a 1 were covered with two boxes. This means is that if the conditions for either box are true, the output will be true. This also means that the simplified Boolean equation will only have two terms. The term for each box can be determined by observing which variables are constant throughout each cell of that box. For the red box, only remains constant through the four cells. switches from the top row to the bottom row, and switches from the left column to the right column. For the blue box, and remains constant through the two cells, while switches from the left cell to the right cell. The two boxes yield the simplified Boolean equation shown in Figure 4.

Figure 4: Simplified Boolean Equation for the ATM Example


This equation meets the conditions in the truth table in Table 1 and achieves the desired result with the minimum number of logic elements.

Combinational Logic Circuits

Lastly, a combinational logic circuit can be created using the simplified equation. First, a NOT operation is performed on by inputting and outputting through a NOT gate. Then, the and inverted are inputted into an AND gate, as denoted by them being multiplied in Figure 4. Finally, the result of the AND operation between the and inverted and the are inputted into an OR gate, as denoted by the addition function in Figure 4. The final combinational logic circuit can be seen in Figure 5.

Figure 5: Combinational Logic Circuit for the ATM Example

Materials and Equipment

  • A 7432 IC (4 dual-input OR gates)
  • A 7408 IC (4 dual-input AND gates)
  • A 7404 IC (6 single-input NOT gates)
  • A lab PC with LabVIEW 2019 software
  • An NI-ELVIS II+ with prototyping board
  • Electrical leads

Problem Statement

Farmer Georgi owns a 350-acre dairy farm in upstate New York. In addition to milk and butter, Farmer Georgi sells fresh eggs at the Union Square Greenmarket in Manhattan. It is imperative that Farmer Georgi protects the hen that produces eggs for his business.

Farmer Georgi has two barns, one hen, and a supply of corn. A fox has been attempting to eat the hen by hiding in a barn. The hen can move freely from one barn to the other. Farmer Georgi sometimes stores corn in one barn and sometimes in the other, but he never stores it in both at the same time. The hen would like to eat the corn and the fox would like to eat the hen. Farmer Georgi needs an alarm system that uses digital logic circuits to protect the hen and the corn. The design should use the fewest logic gates and input variables possible. The alarm will sound if:

  1. The fox and the hen are in the same barn
  2. The hen and the corn are in the same barn

Procedure

1. Test the Integrated Circuits (ICs)

Before performing the lab, the integrated circuits (IC) used in wiring the alarm system on the NI-ELVIS board must be tested to determine if they are functioning. If the procedure is completed without verifying that the ICs work, problems may occur in the circuit that require additional time and troubleshooting. The system for checking the ICs uses an Arduino board to send and receive signals from the AND/OR/NOT chips and determines if they are functioning properly.

First, load the chip onto the Arduino board (Figure 6) and start the Serial Monitor on the Arduino program. The code will cycle through the basic inputs (0, 1 for NOT; 00, 01, 10, 11 for AND/OR) and then send the outputs of each gate in the chip back to the Arduino board. The code compares those results to the expected result. It displays each input/output pair and displays the final result indicating if the chip is functional or defective. The goal is to determine if the gates are outputting the correct results. After, remove the chips carefully from the Arduino board.

Figure 6: IC Testing Setup

2. Procedure

  1. The two barns must be assigned a numeric equivalent before the truth table is prepared. Use 1 for Barn 1 and 0 for Barn 2 (1 does not mean true and 0 does not mean false for the inputs). For the alarm output, use 0 to indicate that the alarm should be off, and 1 to indicate that the alarm should be on.
  2. On a sheet of Lab Notes paper provided by the TAs, create a truth table that includes the three inputs and one output. Assign the input variables. Include all possible scenarios for the hen, the corn, and the fox.
  3. Compute the output column. To do this, analyze the three inputs and logically determine if the alarm will sound in each scenario. Place a 1 in the output column if the alarm will sound and a 0 if it will not.
  4. Note all the combinations that produce a 1 in the output column. Create a Boolean equation from this table that includes each of the inputs that produced a true output.
  5. Create a K-map. Draw a map that lists all the possible combinations from the Boolean equation. Use the Boolean equation to fill in the 1s and 0s on the K-map.
  6. Box the pairs of 1s appropriately. The 1s may only be boxed in powers of 2 starting with the largest possible combination and working down to the smallest. The outcomes that do not contribute to the solution are to be discarded.
  7. This process yields a simplified Boolean equation. Write this simplified Boolean equation down.
  8. Draw a combinational logic circuit of the simplified Boolean equation.
  9. Have a TA approve the steps to obtain the combinational logic circuit for accuracy.
  10. Build the logic circuit in LabVIEW 2019 using the combinational logic circuit that was drawn. Open LabVIEW and select New VI. Go to Window > Tile Left and Right.
  11. Place three switches on the front panel that represent the hen, the corn, and the fox. Place a Boolean indicator on the front panel to represent the output.
  12. Go to the Functions palette > Modern tab > Programming > Boolean and select the AND, NOT, and OR gates necessary for the circuit.
  13. Once the LabVIEW program is complete, have a TA check and approve the circuit.
  14. Build the circuit on a NI-ELVIS II+ prototyping board. On the board, identify each of the three IC chips as an AND, OR, or NOT gate. To do this, read the number on the chip and match it with the numbers shown in Figure 7. Look for the notch at one end of each chip to orient the chip to the diagrams in Figure 7 and to match the pins.
    Figure 7: IC Numbers and Pins
  15. Place the IC chips over the bridge in the NI-ELVIS board (Figure 8).
    Figure 8: IC Chip in Breadboard
  16. Power the chips. Insert one end of an electrical lead into Row 54 (marked +5V) of the NI-ELVIS board. Insert the other end of the lead into Pin 14 of the IC chip. Repeat this process for all three chips.
  17. Ground the chips using the same method. Insert one end of another electrical lead into Row 53 (marked Ground) of the NI-ELVIS board and the other end into Pin 7 of the IC chip. Repeat this process for all three chips.
  18. Look at the top right corner of the breadboard to find the Digital Input/Output (DIO) holes. Select one of the DIO rows to use as one of the input variables and begin wiring the circuit based on the simplified Boolean equation. Assign the other DIO rows for the remaining input variables.
  19. Continue this process until the entire circuit is wired. Insert one end of a lead into the final output of the NI-ELVIS circuit. Attach the other end of the lead to any row for an LED on the board.
  20. Plug in the NI-ELVIS II+ and connect the USB cable to the lab PC.
  21. Power on the NI-ELVIS II+ by toggling the switches on the back of the device and top of the device. When the pop-up window appears, select NI-ELVISmx Instrument Launcher and click OK (Figure 9).
    Figure 9: New Data Acquisition Device Dialog Window
  22. Click on the DigOut Icon on the Instrument Launcher window (Figure 10).
    Figure 10: NI ELVISmx Instrument Launcher Dialog Window
  23. The NI ELVISmx Digital Writer window should appear (Figure 11). Select the appropriate range for the Lines to Write corresponding to the DIO rows used in the wiring. For example, if the fox, hen, and corn are wired to DIO 21, 22, and 23, select 16–23 for the Lines to Write.
    Figure 11: Digital Writer Window
  24. Click Run and toggle the switches corresponding to the fox, hen, and corn. Observe the LED for the alarm light up based on the inputs to each barn.
  25. Have a TA check the circuit.

The lab work is now complete. Please clean up the workstation. Return all unused materials to a TA.

Assignment

Team Lab Report

Follow the lab report guidelines laid out in the EG1003 Writing Style Guide in the Technical Writing section of the manual. The following points should be addressed in the appropriate section of the lab report.

  • Describe the problem statement regarding Farmer Georgi
  • Describe how AND, OR, and NOT gates work
  • Include the truth table, Boolean equation, K-map, simplified Boolean equation, and combinational logic circuit developed during the lab
  • What is a truth table? How does it contribute to obtaining a Boolean equation?
  • What is a K-map? How does it contribute to obtaining a simplified Boolean equation? To demonstrate the simplification, show what the equation would look like if terms were written for each of the true values and the simplified equation by applying the K-map. Discuss how much simpler the circuitry is as a result of applying the K-map
  • Describe how to construct a digital logic circuit using Boolean equations and K-maps
  • Explain why the alarm system did or did not work
  • Why is there a need for the minimization of a logic design and what are the advantages?
  • How does the use of a combinational logic circuit contribute to advances in technology?
  • Discuss other possible design/procedural improvements
  • Describe how the final combinational logic circuit was obtained
  • Include a screenshot of the front and back panels of the LabVIEW VI

Remember: Lab notes must be taken. Experimental details are easily forgotten unless written down. EG1003 Lab Notes paper can be downloaded and printed from the EG1003 Website. Use the lab notes to write the Procedure section of the lab report. At the end of each lab, a TA will scan the lab notes and upload them to the Lab Documents section of the EG1003 Website. One point of extra credit is awarded if the lab notes are attached at the end of the lab report. Keeping careful notes is an essential component of all scientific practice.

Team PowerPoint Presentation

Follow the presentation guidelines laid out in the EG1003 Lab Presentation Format in the Technical Presentations section of the manual. When preparing the presentation, consider the following points.

  • How does digital logic impact the world today?
  • Looking into the future, how will digital logic change the world?
  • Include the truth table, Boolean equation, K-map, simplified Boolean equation, and combinational logic circuit developed during the lab

References

Boole, George, Encyclopedia Britannica, 2003. Encyclopedia Britannica Online. Retrieved July 29, 2003 http://www.britannica.com/eb/article?eu=82823