Difference between revisions of "AutoCAD Skill Builder"

From EG1004 Lab Manual
Jump to: navigation, search
(2015-08-21 Jack Bringardner)
 
(41 intermediate revisions by the same user not shown)
Line 1: Line 1:
<h1 align=center>EG1004 Lab 2: Software for Engineers II</h1>
<h2>Objective</h2>
<h2>Objective</h2>
<p>In this exercise, you will be introduced to additional software used
<p>In this exercise, you will be introduced to additional software used
by technical professionals. You will basic technical
by technical professionals. You will learn basic technical
design methods using Computer-Aided Design (CAD) software, specifically
design methods using Computer-Aided Design (CAD) software, specifically
AutoCAD. Later on in the course, you will use this knowledge to create
AutoCAD. Later on in the course, you will use this knowledge to create
designs, particularly in your semester-long design project. In addition,
designs, particularly in your semester-long design project.</p>
you will learn some basic analytical software, Matlab</p>


<h2>Overview:</h2>
<h2>Overview</h2>


<p>In any design process, engineers must put their ideas on
<p>In any design process, engineers must put their ideas on
Line 63: Line 60:
<h2>Starting and Setting Up AutoCAD</h2>
<h2>Starting and Setting Up AutoCAD</h2>


<p>Start AutoCAD LT 2002. (<i>Note: It is best to have a 3 button mouse.)</i></p>
<p>Start AutoCAD 2010. (''Note: It is best to have a 3 button mouse.'')</p>
 
<p>Once the program has loaded, make sure that you have the AutoCAD LT Today window
(See Figure 3). </p>
 
<p align=center>[[Image:image008.jpg]]</p>
 
<p class=caption>Figure 3</p>
 
<p>If not, you may also access AutoCAD Today from the Tools menu bar  (See Figure 4).</p>
 
<p align=center>[[Image:image009.jpg]]</p>
 
<p class=caption>Figure 4</p>
 
<p>On the AutoCAD LT Today window, click the Create Drawing tab
and select Wizard from the drop down menu and click on Advanced Setup which is
shown below in Figure 5.</p>
 
<p align=center>[[Image:image011.jpg]]</p>
 
<p class=caption>Figure 5</p>
 
<p>In the Advanced Setup wizard select the unit of measurement
to be Engineering and choose the Precision to be two decimal places. Then click
next (See Figure 6).</p>
 
<p align=center>[[Image:image012.jpg]]</p>
 
<p class=caption>Figure 6</p>
 
<p>Select the direction for angle measurement to be East then click next.</p>
 
<p>Select the orientation for angle measurement to be
Counter-Clockwise then click next.  </p>
 
<p>Then, enter the areas you want to represent using full scale
units (See Figure 7). Example:  if you
want a 100 ft x 100 ft area, your width would be: 100’ and your length:  100’.  </p>
 
<p align=center>[[Image:image013.jpg]]</p>
 
<p class=caption>Figure 7</p>
 
<h2>Setting Up Work Area</h2>
 
<p>Now that our page is setup, let’s set up the work area. </p>
 
<p>On AutoCAD LT you will have a similar work space shown below in Figure 8.</p>


<p align=center>[[Image:image014.jpg]]</p>
<p>Note: Beginning with AutoCAD 2010, Autodesk has changed the toolbar interface to resemble that of Microsoft Office's ribbon interface.</p>


<p class=caption>Figure 8</p>
<p>Once the program has loaded, you can close the '''Welcome Screen'''. Note that the tutorials on the left hand side are very useful and should be reviewed later on.</p>


<p>First go to view and select toolbars. (See Figure 9)</p>
[[Image:image008.jpg|frame|center|Figure 3]]


<p align=center>[[Image:image015.jpg]]</p>
<p>In the command box (bottom of the screen) type ''startup'' and the message '''startup(0)''' will appear. Type''1'' then press enter. Now go to the top of the page next to where it says 2D Drafting and Annotations will be the icon for a new blank project. Press this button and a '''Create New Drawing''' window will appear. Select the last option at the top of this window which will be ''Use a Wizard'' (see Figure 4).</p>


<p class=caption>Figure 9</p>
[[Image:image011.jpg|frame|center|Figure 4]]


<p>Select the following toolbars:  Dimension, Inquiry, Object Snap, and Zoom. (See Figure 10)</p>
<p>Select ''Advanced Setup'' and the following window shown in Figure 5 will appear</p>


<p align=center>[[Image:image017.jpg]]</p>
[[Image:image012.jpg|frame|center|Figure 5]]


<p class=caption>Figure 10</p>
<p>For the length unit, select the type to be ''Engineering'' and choose the precision to be two decimal places. Then click next (See Figure 5).</p>


<p>You may place the toolbar where is easy accessible. </p>
<p>The wizard will then take you through the setup for '''Angles''', '''Angle Measurement''', '''Angle Direction''', and '''Area''' The defaults that appear can be left as is unless working on a special project. For the skill builder below, the default settings are correct.</p>


<h2>Setting Up the Dimensions and the Text Style</h2>
<h2>Setting Up the Dimensions and the Text Style</h2>


<p>Later on, we will be inputting text and dimensions into our
<p>Later on, we will be inputting text and dimensions into our
drawing. However, it is best to setup a general style for the drawing due to
drawing. However, it is best to set up a general style for the drawing due to
the fact that the default settings are not sufficient for our needs. </p>
the fact that the default settings are not sufficient for our needs.</p>


<p>First, select the Dimension from the menu bar and select style. (See Figure 11)</p>
<p>First, select the ''Annotate'' tab on the ribbon. Click the arrow at the lower right-hand corner of the '''Dimensions''' group to access the '''Dimension Style Manager''' dialog window. (See Figure 6)</p>


<p align=center>[[Image:image018.jpg]]</p>
[[Image:image018.jpg|frame|center|Figure 6]]


<p class=caption>Figure 11</p>
<p>In the '''Dimension Style Manager''' window, select ''Modify...''. (See Figure 7)</p>


<p>On the style window select modify. (See Figure 12)</p>
[[Image:image019.jpg|frame|center|Figure 7]]


<p align=center>[[Image:image019.jpg]]</p>
<p>Under the '''Lines''' tab, change the following:</p>
<ul>
<li>'''Offset from origin''': 1'</li>
</ul>


<p class=caption>Figure12</p>
<p>Under the '''Symbols and Arrow''' tab, change the following:</p>
<ul>
<li>'''Arrow Size''': 1'</li>
</ul>


<p>On the Lines and Arrow tab, change the following:</p>
<p>Under the '''Text''' tab, change the following:</p>
<ul>
<ul>
<li>Offset from Origin: 1’</li>
<li>'''Text Height''': 1'</li>
<li>Arrow Size: 1’</li>
</ul>
</ul>


<p>On the Text tab, change the following:</p>
<p>Under the '''Primary Units''' tab, change the following:</p>
<ul>
<ul>
<li>Text height: 1’</li>
<li>'''Unit Format''': Engineering</li>
<li>'''Precision''': 0'-0.00"</li>
</ul>
</ul>


<p>To change the Text style: On the menu bar select Format and
<p>To change the text style, click the arrow at the lower right-hand corner of the '''Text''' group of the '''Annotate''' tab on the ribbon. (See Figure 8)</p>
then select Text Style. (See Figure 13)</p>
 
 
<p align=center>[[Image:image020.jpg]]</p>
 
<p class=caption>Figure 13</p>


<p>You may choose the type of font and change the height to 1’
[[Image:image020.jpg|frame|center|Figure 8]]
as shown below in Figure 14.</p>


<p align=center>[[Image:image021.jpg]]</p>
<p>You may choose the type of font and change the height to 1' as shown below in Figure 9.</p>


<p class=caption>Figure 14</p>
[[Image:image021.jpg|frame|center|Figure 9]]


<h2>Command Window</h2>
<h2>Command Window</h2>


<p>At the bottom of the screen, you see a separate window
<p>At the bottom of the screen, you see a separate window showing a few lines of text. (You can change it to show as many lines as you like by dragging the top edge of the window up or down.) Notice the word ''Command''. This is the command line. All commands can be executed by typing them on the command line.  Even if you use a menu item or toolbar button to execute a command, you may need to look at the command line to see how AutoCAD responds. Often, AutoCAD provides options that must be typed in from the keyboard. Also, text that you type appears on the command line. For example, when you type in coordinates specifying a point, they appear on the command line. To see more of the command line, press F2 to open the AutoCAD Text window. You can scroll back through previous commands. Press F2 again to close the window. (See Figure 10)</p>
showing approximately five lines of text. (You can change it to show as many
lines as you like by dragging the top edge of the window up or down.) Notice
the word Command:. This is the command line. All
commands can be executed by typing them on the command line.  Even if you use a menu item or toolbar
button to execute a command, you may need to look at the command line to see
how AutoCAD responds. Often, AutoCAD provides options that must be typed in
from the keyboard. Also, text that you type appears on the command line. For
example, when you type in coordinates specifying a point, they appear on the
command line. To see more of the command line, press F2 to open the AutoCAD
Text window. You can scroll back through previous commands. Press F2 again to
close the window. (See Figure 15)</p>


<p align=center>[[Image:image022.jpg]]</p>
[[Image:image022.jpg|frame|center|Figure 10]]


<p class=caption>Figure 15</p>
<h2>AutoCAD Tools </h2>
 
<h3>Draw Tools</h3>
<h3>To Draw a Line</h3>
<h4>To Draw a Line</h4>
<ol>
<ol>
<li>Type Line or L in the command window, then Enter, or
<li>Type ''line'' or ''l'' in the command window, then ''Enter'', or click the '''Line''' icon [ [[Image:image023.jpg]] ] in the '''Draw''' group under the '''Home''' tab.</li>
click the Line icon [ [[Image:image023.jpg]] ] to invoke
<li>Click the point where you want the line to begin. Drag the line in the direction you want it to go, and specify its length when prompted. Hit ''Enter''.</li>
the Line command.</li>
<li>Press ''Escape'' to exit the '''line''' command.</li>
<li>Click the point where you want the line to begin. Drag the line in the direction
you want it to go, and specify its length when prompted. Hit Enter.</li>
<li>Press Escape to exit the Line command.</li>
</ol>
</ol>


<p><i><b>Note:</b> Most of the commands can be done by clicking
<p><i><b>Note:</b> Most of the commands can be done by clicking an icon or typing into the command window.</i></p>
an icon or typing into the command window.</i></p>
 
<h3>Drawing Lines with specific angles and length</h3>


<p>Polar coordinates take the form distance&lt;angle. Relative
<h4>Drawing Lines with Specific Angles and Lengths</h4>
polar coordinates must have the @ sign before the
coordinate.</p>


<p>By default, angles are measured according to Figure 16.</p>
<p>Relative polar coordinates take the form ''distance''&lt;''angle''.</p>


<p align=center>[[Image:image024.jpg]]</p>
<p>By default, angles are measured according to Figure 11.</p>


<p class=caption>Figure 16</p>
[[Image:image024.jpg|frame|center|Figure 11]]


<p>In order to draw a line that is 10’ at a 30º angle:</p>
<p>In order to draw a line that is 10' at a 30º angle:</p>
<ol>
<ol>
<li>Click on the Line icon [ [[Image:image023.jpg]] ].</li>
<li>Click on the '''Line''' icon [ [[Image:image023.jpg]] ].</li>
<li>Click the point where you want the line to begin.</li>
<li>Click the point where you want the line to begin.</li>
<p>Then type in the Command Window:  @distance&lt;angle. Hit Enter. </p>
<p>Then type in the Command Window:  ''distance''&lt;''angle''. Hit ''Enter''. </p>
<p>EX: @10’&lt;30, then Hit Enter</p>
<p>EX: 10'&lt;30, then hit ''Enter''</p>
<li>Press Escape to exit the Line Command.</li>
<li>Press ''Escape'' to exit the '''Line''' command.</li>
</ol>
</ol>


<h3>Below the Command Window</h3>
<h4>Drawing Arcs</h4>


<p>[[Image:image025.jpg]]</p>
<p>To draw an arc, choose Arc [ [[Image:image043.jpg]] ] from the
Draw toolbar and follow the prompts. As with circles, object snaps are often
helpful when drawing arcs.</p>


<ol>
<p>When drawing an arc by using the Start, End, and Radius options, the three specifications
<li>When in orthogonal mode—ortho mode as it’s called for short—you can only draw
actually define two possible arcs, one minor and one major. AutoCAD draws the minor arc by
orthogonal (right angles) lines with the mouse. Ortho mode also affects editing.
default, in the counterclockwise direction. (A minor arc is less than half a circle.) If you
For example, with ortho mode on, you can only move objects vertically or horizontally.
enter a negative number for the radius, AutoCAD draws the major arc (which is more than
Combined with snap and grid, ortho mode makes drawing easier and more efficient. Ortho
half a circle). The options requiring an angle also define two possible arcs, one drawn
mode is also great for direct distance entry.  Click ORTHO on the status bar to toggle
counterclockwise and one drawn clockwise.</p>
ortho mode on and off. You cannot have polar tracking on at the same time that ortho
mode is on.</li>


<li>Osnap allows a user to precisely acquire certain points on a line or object to be
<p>AutoCAD draws the counterclockwise arc by default. If you type a negative number for the
able to manipulate the drawing, such as aligning or attaching those points that are
angle, AutoCAD draws the arc clockwise.</p>
selected to other points.</li>


<p>Example:</p>
<h4>Drawing Dimensions</h4>


<p align=center>[[Image:image027.jpg]]</p>
<p>Just as the most common objects are lines, the most common
dimensions are linear dimensions.</p>


<p class=caption>Figure 17</p>
<p>Use linear dimensions for lines, a straight segment of a polyline, or a straight
segment in a block. You can also use a linear dimension for arcs and circles—you
get the linear length of the arc (not its perimeter length) and the diameter of
the circle.</p>


<p>In order to draw a line from endpoint A to endpoint B in
<p>When dimensioning a drawing, create a new layer and label the
Figure 17 accurately and insure that we are actually attaching the ends of the
dimensions so that you can toggle the layer on and off. That way, when you modify your
lines and not the space before, near, or around it, we utilize a command called
drawing, there will be less clutter on the screen.</p>
“osnap�?.</p>


<p>To toggle osnap on and off, click the “OSNAP�? button shown in Figure 18.</p>
<p>To dimension a line, choose Dimension from the menu bar and select linear.
 
AutoCAD responds with the <i>Specify first extension line origin or &lt;select
<p align=center>[[Image:image029.jpg]]</p>
object&gt;:</i> prompt. You can now either pick two extension line origin points or
 
press Enter (or right-click) and select an object for dimensioning. (See Figure 23)</p>
<p class=caption>Figure 18</p>


<p>Step 1:  Click on the line icon [ [[Image:image023.jpg]] ] and
[[Image:image066.jpg|frame|center|Figure 23]]
when you situate the crosshair at the endpoint of line A and you will notice a pink
box appear.  This means that the endpoint has acquired by AutoCAD.</p>


<p>Step 2:  Once the endpoint of line A has been acquired, click and move the
<h3>Modify Tools</h3>
crosshair to the end of line B.  You will notice that the endpoint of line B has been
<h4>Offsetting Objects</h4>
found by AutoCAD.</p>
 
<p>Step 3:  Click and press enter to complete the line command function.</p>
 
<p><i><b>Note:</b>  To click on different points of a line, you
will need to change the osnap settings.  In order to go to
the settings of osnap, you will have to right click
on the Osnap tab and the drafting setting will appear
as shown in Figure 19.</i></p>
 
<p align=center>[[Image:image030.jpg]]</p>
 
<p class=caption>Figure 19</p>
 
<p>If you have the object snap toolbar, you can toggle on and off the desired osnap by
click on it after you have selected the line icon. (See Figure 20)</p>
 
<p align=center>[[Image:image031.jpg]]</p>
 
<p class=caption>Figure 20</p>
 
<li>LWT is the Line Weight function, and it controls the width of the line. A lineweight
can help to distinguish various elements of your drawing, both on-screen and on paper.
For example, you could use a thicker lineweight to indicate planned construction changes,
for dimension lines, or even to represent the true width of an object. The LWT button on
the status bar turns on and off the display of lineweights. By default, LWT is off.
(See Figure 21)</li>
</ol>
 
<p align=center>[[Image:image033.jpg]]</p>
 
<p class=caption>Figure 21</p>
 
<p>In order to select the line width of a line, first select the line(s) and then click
on the Line Weight Control and select the desired thickness as show in Figure 22.</p>
 
<p align=center>[[Image:image035.jpg]]</p>
 
<p class=caption>Figure 22</p>
 
<h3>Offsetting Objects</h3>
<p>The Offset command creates lines or curves parallel to one
<p>The Offset command creates lines or curves parallel to one
existing object. The beauty of this command is apparent when you start to
existing object. The beauty of this command is apparent when you start to
Line 315: Line 202:
treated as one object. Using OFFSET, you can create concentric polygons, for
treated as one object. Using OFFSET, you can create concentric polygons, for
example the figure below shows three concentric polygons. The red polygon was
example the figure below shows three concentric polygons. The red polygon was
created with the POLYGON [ [[Image:image036.jpg]] ] command, and the blue polygon was created by using OFFSET as
created with the POLYGON [ [[Image:image036.jpg]] ] command, which is found under the Home tab by clicking the arrow at the bottom right corner of the Draw group and selecting the polygon button shown above. The blue polygon was subsequently created by using OFFSET as
shown in Figure 23.</p>
shown in Figure 18.</p>


<p>Example:</p>
<p>Example:</p>


<p align=center>[[Image:image038.jpg]] [[Image:image040.jpg]]</p>
<div><div style="float: left; display: inline;">[[Image:image038.jpg|frame|center|Figure 18a]]</div><div style="float: left; display: inline; width: 10%;">&nbsp;</div><div style="float: left; display: inline;">[[Image:image040.jpg|frame|center|Figure 18b]]</div></div><br clear="both" />
 
<p class=caption>Figure 23</p>


<p>To offset a line or an object:</p>
<p>To offset a line or an object:</p>
<ol>
<ol>
<li>Click [[Image:image041.jpg]] and then on the command window specific
<li>Click [[Image:image041.jpg]], found under the Home tab in the Modify group, and then on the command window specify
offset distance and then press Enter.</li>
offset distance and then press Enter.</li>


Line 332: Line 217:
</ol>
</ol>


<h3>Drawing Arcs</h3>
<h4>Mirroring Objects</h4>
 
<p>To draw an arc, choose Arc [ [[Image:image043.jpg]] ] from the
Draw toolbar and follow the prompts. As with circles, object snaps are often
helpful when drawing arcs.</p>
 
<p>When drawing an arc by using the Start, End, and Radius options, the three specifications
actually define two possible arcs, one minor and one major. AutoCAD draws the minor arc by
default, in the counterclockwise direction. (A minor arc is less than half a circle.) If you
enter a negative number for the radius, AutoCAD draws the major arc (which is more than
half a circle). The options requiring an angle also define two possible arcs, one drawn
counterclockwise and one drawn clockwise.</p>
 
<p>AutoCAD draws the counterclockwise arc by default. If you type a negative number for the
angle, AutoCAD draws the arc clockwise.</p>
 
<h3>Rotating an Object</h3>
 
<p>To rotate an object, choose Rotate [ [[Image:image044.jpg]] ] from the
Modify toolbar and select an object. Alternatively, select an object and then
choose Rotate from the Modify toolbar. At the Specify base point: prompt from
the command window, indicate the point around which you want to rotate. At the
Specify rotation angle or [Reference]: prompt, type an angle at the command
line.</p>
 
<p>The Reference option lets you specify an absolute existing
rotation angle and the desired angle. At the Specify the reference angle
&lt;0&gt;: prompt, you type in an angle or specify an angle by picking two
points. These can be object snap points on the object that specify the object’s
current angle. At the Specify the new angle: prompt,
type or pick a new angle. You can also pick an object snap on another object in
the drawing to indicate this new angle. You can use the Reference option to align
the object with the X or Y axis or with another object in your drawing.</p>
 
<h3>Mirroring Objects</h3>


<p>Many drawings have symmetrical elements. Often, especially in
<p>Many drawings have symmetrical elements. Often, especially in
Line 379: Line 230:
<p>AutoCAD prompts for the first and second points of the mirror line. This is an imaginary
<p>AutoCAD prompts for the first and second points of the mirror line. This is an imaginary
line across which AutoCAD creates the mirrored object. The length of the line is
line across which AutoCAD creates the mirrored object. The length of the line is
irrelevant—only its start point and direction are important.</p>
irrelevant &mdash; only its start point and direction are important.</p>


<p><i><b>Note:</b> Most mirror lines are orthogonal. Therefore, after you specify the first
<p><i><b>Note:</b> Most mirror lines are orthogonal. Therefore, after you specify the first
Line 386: Line 237:
orthogonal mirror line.</i></p>
orthogonal mirror line.</i></p>


<p>Example based on a mounting plate shown in Figure 24</p>
<p>Example based on a mounting plate shown in Figure 19</p>
<ol>
<ol>
<li>Choose Mirror from the Modify toolbar. <i>Select objects:</i> prompt
<li>Choose Mirror from the Modify toolbar. <i>Select objects:</i> prompt
Line 393: Line 244:


<li>At the Specify first point of mirror line: prompt, pick the intersection
<li>At the Specify first point of mirror line: prompt, pick the intersection
[[Image:image047.jpg]] in Figure 24. At the <i>Spe</i>cify second point of
[[Image:image047.jpg]] in Figure 19. At the <i>Spe</i>cify second point of
mirror line: prompt, pick the intersection[[Image:image049.jpg]].</li>
mirror line: prompt, pick the intersection[[Image:image049.jpg]].</li>


Line 403: Line 254:
and then press Enter.</li>
and then press Enter.</li>


<p align=center>[[Image:image051.jpg]]</p>
[[Image:image051.jpg|frame|center|Figure 19]]
 
<p class=caption>Figure 24</p>


<li>At the <i>Specify first point of mirror line:</i> prompt, pick the intersection
<li>At the <i>Specify first point of mirror line:</i> prompt, pick the intersection
Line 412: Line 261:
Enter again at the <i>Delete source objects? [Yes/No] &lt;N&gt;:</i> prompt.</li>
Enter again at the <i>Delete source objects? [Yes/No] &lt;N&gt;:</i> prompt.</li>


<li>AutoCAD completes the mounting plate seen in Figure 25.</li>
<li>AutoCAD completes the mounting plate seen in Figure 20.</li>
</ol>
</ol>


<p align=center>[[Image:image056.jpg]]</p>
[[Image:image056.jpg|frame|center|Figure 20]]


<p class=caption>Figure 25</p>
<h4>Trimming objects</h4>
 
<h3>Trimming objects</h3>


<p>As you edit a drawing, you may find that lines or arcs that
<p>As you edit a drawing, you may find that lines or arcs that
Line 426: Line 273:
object you want to trim. You define the cutting edge by selecting an object.
object you want to trim. You define the cutting edge by selecting an object.
You can select several cutting edges and several objects to trim at one time,
You can select several cutting edges and several objects to trim at one time,
as shown in Figure. When you select an object to trim, you must pick the object
as shown in Figure 21. When you select an object to trim, you must pick the object
on the side that you want trimmed (not on the side that you want to remain). A
on the side that you want trimmed (not on the side that you want to remain). A
common use for the TRIM command is to create intersections of walls in
common use for the TRIM command is to create intersections of walls in
Line 434: Line 281:
objects by pressing the Shift key as you select objects to trim.</p>
objects by pressing the Shift key as you select objects to trim.</p>


<p align=center>[[Image:image058.jpg]]</p>
[[Image:image058.jpg|frame|center|Figure 21]]
 
<p class=caption>Figure 26</p>


<p>To trim an object, choose Trim [ [[Image:image060.jpg]] ] from the
<p>To trim an object, choose Trim [ [[Image:image060.jpg]] ] from the
Modify toolbar. You cannot select objects before starting the TRIM command.
Modify toolbar. You cannot select objects before starting the TRIM command.
AutoCAD displays the <i>Current settings:
AutoCAD displays the <i>Current settings:
Projection=UCS, Edge=Non,e
Projection=UCS, Edge=None,
Select cutting edges ... Select objects:</i> prompt. AutoCAD lets you know the
Select cutting edges ... Select objects:</i> prompt. AutoCAD lets you know the
values of the two system variables that affect trimming. The Projection setting
values of the two system variables that affect trimming. The Projection setting
Line 448: Line 293:
cutting edge and the object to be trimmed. At this prompt, pick the object(s)
cutting edge and the object to be trimmed. At this prompt, pick the object(s)
that you want to use as a cutting edge. Press Enter to end object selection. (See
that you want to use as a cutting edge. Press Enter to end object selection. (See
Figure 26)</p>
Figure 21)</p>


<p>Now you may be able to cut the lines within the cutting
<p>Now you may be able to cut the lines within the cutting
edges. Use the Undo (CTRL+Z) option if the results of the trim are not what you
edges. Use the Undo (CTRL+Z) option, or type ''u'' then press ''Enter'', if the results of the trim are not what you
want. You can then continue to select objects to trim.</p>
want. You can then continue to select objects to trim.</p>


<h3>Layers</h3>
<h4>Rotating an Object</h4>
 
<p>To rotate an object, choose Rotate [ [[Image:image044.jpg]] ] from the
Modify toolbar and select an object. Alternatively, select an object and then
choose Rotate from the Modify toolbar. At the Specify base point: prompt from
the command window, indicate the point around which you want to rotate. At the
Specify rotation angle or [Reference]: prompt, type an angle at the command
line.</p>
 
<p>The Reference option lets you specify an absolute existing
rotation angle and the desired angle. At the Specify the reference angle
&lt;0&gt;: prompt, you type in an angle or specify an angle by picking two
points. These can be object snap points on the object that specify the object's
current angle. At the Specify the new angle: prompt,
type or pick a new angle. You can also pick an object snap on another object in
the drawing to indicate this new angle. You can use the Reference option to align
the object with the X or Y axis or with another object in your drawing.</p>
 
<h4>Hatching</h4>
 
<p>To hatch an area, select Draw from the menu bar and select
Hatch icon [ [[Image:Image112.jpg]] ] in the Draw group under the Home tab. AutoCAD opens a new tab, ''Hatch Creation'', as shown below in Figure
26.</p>
 
[[Image:Image113.jpg|frame|center|Figure 26]]
 
<p>Click on the arrow at the bottom right corner of the ''Options'' to open the ''Hatch and Gradient'' window.</p>
 
[[Image:image070.jpg|frame|center|Figure 27]]
 
<p>Use this dialog box to define your hatch. From the Type and Pattern drop-down box, choose one
of the three options:</p>
 
<ol>
<li><b>Predefined</b>: Enables you to select one of AutoCAD's hatch patterns.</li>
 
<li><b>User-defined</b>: Enables you to define your own hatch pattern by
specifying the angle and spacing, using the current linetype.</li>
 
<li><b>Custom</b>: Enables you to choose a pattern you have created in your own .pat
file.</li>
</ol>
 
<p>Click the Pattern drop-down box to choose the hatch patterns from a list.
(See Figure 28)</p>
 
[[Image:image071.jpg|frame|center|Figure 28]]
 
<p>In the palette, click the tabs to see the different types of
hatches. Click the image tile to choose a hatch pattern and click OK.</p>
 
<h4>Determining Hatching Boundaries</h4>
 
<p>The hardest part of hatching is placing the hatch, not
defining it. Hatching an entire object is the simplest way to place a hatch.
But often the area you want to hatch is fairly complex, and AutoCAD needs to do
some calculations to determine it. The Boundary Hatch dialog box offers two
ways to specify the hatch boundary— you can pick points inside an area and let
AutoCAD try to find an enclosed boundary, or you can select objects. If you
want to hatch an entire object:</p>
 
 
<ol>
<li>Choose Select Objects. AutoCAD returns you temporarily to your drawing.</li>
 
<li>Select all the objects you want to hatch. You can use all the standard object
selection options to select objects. Remove and Add are especially helpful.</li>
 
<li>Press Enter to end object selection and return to the dialog box.</li>
</ol>
 
<p>If the area you want to hatch does not neatly fit into one or more objects,
choose <i>Pick Points</i>. At the <i>Select internal point</i>: prompt, pick a point
that is inside the boundary that you want to hatch. You can continue to pick internal
points to hatch adjoining areas. AutoCAD helpfully highlights the boundaries it finds.
Press Enter to return to the dialog box.</p>
 
<h3>File Tools</h3>
<h4>Layers</h4>


<p>The best way to organize your drawing into colors, linetypes, and lineweights is to use
<p>The best way to organize your drawing into colors, linetypes, and lineweights is to use
Line 494: Line 417:
<p>Creating a new layer:</p>
<p>Creating a new layer:</p>


<p>To create a new layer, choose Layer Properties Manager [ [[Image:image061.jpg]] ] from the
<p>To create a new layer, select the Layer Properties Manager [ [[Image:image061.jpg]] ] from the
Layers toolbar [ [[Image:image062.jpg]] ].</p>
Layers group under the Home tab.</p>


<p>AutoCAD opens the Layer Properties Manager, as shown in Figure 27.</p>
<p>AutoCAD opens the Layer Properties Manager, as shown in Figure 22.</p>


<p align=center>[[Image:image064.jpg]]</p>
[[Image:image064.jpg|frame|center|Figure 22]]
 
<p class=caption>Figure 27</p>


<p>This dialog box lists all current layers and their properties. You can also create
<p>This dialog box lists all current layers and their properties. You can also create
new layers and modify current ones.</p>
new layers and modify current ones.</p>


<h3>Drawing Dimensions</h3>
<h4>Below the Command Window</h4>


<p>Just as the most common objects are lines, the most common
<p>[[Image:image025.jpg]]</p>
dimensions are linear dimensions.</p>
 
<p>Use linear dimensions for lines, a straight segment of a polyline, or a straight
segment in a block. You can also use a linear dimension for arcs and circles—you
get the linear length of the arc (not its perimeter length) and the diameter of
the circle.</p>
 
<p>When dimensioning a drawing, create a new layer and label the
dimensions so that you can toggle the layer on and off. That way, when you modify your
drawing, there will be less clutter on the screen.</p>
 
<p>To dimension a line, choose Dimension from the menu bar and select linear.
AutoCAD responds with the <i>Specify first extension line origin or &lt;select
object&gt;:</i> prompt. You can now either pick two extension line origin points or
press Enter (or right-click) and select an object for dimensioning. (See Figure 28)</p>


<p align=center>[[Image:image066.jpg]]</p>
<p>From left to right: Infer Constraints, Snap Mode, Grid, Ortho Mode, Polar Tracking, Object Snap, 3D Object Snap, Object Snap Tracking UCS, Allow/Disallow Dynamic, Dynamic Input, Show/Hide Lineweight, Show/Hide Transparency, Quick Properties, Select Cycling.</p>


<p class=caption>Figure 28</p>
<h3>Inserting an External reference [Title Block]</h3>
<p>External references (commonly called xrefs) enable you to view any drawing as a
reference while in your current drawing. The external drawing is not part of your
current drawing.  The current drawing keeps track of the location and name of an
external reference so you can always reference it easily. As with blocks, you can
snap to objects in the external reference, thereby using it as a reference for the
drawing process. You can also change the visibility settings of the xref’s layers.</p>
<p>To insert external reference:</p>
<ol>
<ol>
<li>Click on the Insert on the menu bar and select External Reference.</li>
<li>When in orthogonal mode—ortho mode as it's called for short—you can only draw
<li>Select ANSI A title block from the template folder.</li>
orthogonal (right angles) lines with the mouse. Ortho mode also affects editing.
<li>Make sure that the boxes are unchecked for the Specify On-screen. </li>
For example, with ortho mode on, you can only move objects vertically or horizontally.
Combined with snap and grid, ortho mode makes drawing easier and more efficient. Ortho
mode is also great for direct distance entry.  Click ORTHO on the status bar to toggle
ortho mode on and off. You cannot have polar tracking on at the same time that ortho
mode is on.</li>


<p align=center>[[Image:image067.jpg]]</p>
<li>Object snap (osnap) allows a user to precisely acquire certain points on a line or object to be
able to manipulate the drawing, such as aligning or attaching those points that are
selected to other points.</li>


<p class=caption>Figure 29</p>
<p>Example:</p>


<p>The drawing’s scale is set to be 1"=10’. Since there are 12 inches in 1 foot and
[[Image:image027.jpg|frame|center|Figure 12]]
the scale is set to be 1 inch per 10 feet. You would get 12 x 10 = 120, thus making
the Scale for X, Y and Z to be 120. (See Figure 29)</p>


<li>Click OK to complete operation. (See Figure 30)</li>
<p>In order to draw a line from endpoint A to endpoint B in
</ol>
Figure 12 accurately and ensure that we are actually attaching the ends of the
lines and not the space before, near, or around it, we utilize a command called
"osnap".</p>


<p align=center>[[Image:image069.jpg]]</p>
<p>To toggle osnap on and off, click the "OSNAP" button. Figure 13 shows the use of osnap.</p>


<p class=caption>Figure 30</p>
[[Image:image029.jpg|frame|center|Figure 13]]


<h3>Hatching</h3>
<p>Step 1:  Click on the line icon [ [[Image:image023.jpg]] ] and
when you situate the crosshair at the endpoint of line A and you will notice a pink
or green box appear.  This means that the endpoint has acquired by AutoCAD.</p>


<p>To hatch an area, select Draw from the menu bar and select
<p>Step 2:  Once the endpoint of line A has been acquired, click and move the
Hatch command. AutoCAD opens the Boundary Hatch dialog box shown below in Figure
crosshair to the end of line B. You will notice that the endpoint of line B has been
31.</p>
found by AutoCAD.</p>


<p align=center>[[Image:image070.jpg]]</p>
<p>Step 3: Click and press enter to complete the line command function.</p>


<p class=caption>Figure 31</p>
<p><i><b>Note:</b> To click on different points of a line, you
will need to change the osnap settings.  In order to go to
the settings of osnap, you will have to right click
on any part below the command window and a context menu will appear. See Figure 14.</i></p>


<p>Use this dialog box to define your hatch. From the Type drop-down box, choose one
[[Image:image030.jpg|frame|center|Figure 14]]
of the three options:</p>


<ol>
<p>Select settings and then you can choose the settings for which option you would like to change. (See Figure 15)</p>
<li><b>Predefined</b>: Enables you to select one of AutoCAD’s hatch patterns.</li>


<li><b>User-defined</b>: Enables you to define your own hatch pattern by
[[Image:image031.jpg|frame|center|Figure 15]]
specifying the angle and spacing, using the current linetype.</li>


<li><b>Custom</b>: Enables you to choose a pattern you have created in your own .pat
<li>LWT is the Lineweight function, and it controls the width of the line. A lineweight
file.</li>
can help to distinguish various elements of your drawing, both on-screen and on paper.
For example, you could use a thicker lineweight to indicate planned construction changes,
for dimension lines, or even to represent the true width of an object. The LWT button on
the status bar turns on and off the display of lineweights. By default, LWT is off.
(See Figure 16)</li>
</ol>
</ol>


<p>Click the Pattern drop-down box to choose the hatch patterns from a list.
[[Image:image033.jpg|frame|center|Figure 16]]
(See Figure 32)</p>


<p align=center>[[Image:image071.jpg]]</p>
<p>In order to select the line width of a line, first select the line(s) and then click
on the Line Weight Control and select the desired thickness as show in Figure 17.</p>


<p class=caption>Figure 32</p>
[[Image:image035.jpg|frame|center|Figure 17]]


<p>In the palette, click the tabs to see the different types of
<h4>Inserting an External reference [Title Block]</h4>
hatches. Click the image tile to choose a hatch pattern and click OK. </p>


<h3>Determining Hatching Boundaries</h3>
<p>External references (commonly called xrefs) enable you to view any drawing as a
reference while in your current drawing. The external drawing is not part of your
current drawing.  The current drawing keeps track of the location and name of an
external reference so you can always reference it easily. As with blocks, you can
snap to objects in the external reference, thereby using it as a reference for the
drawing process. You can also change the visibility settings of the xref's layers.</p>


<p>The hardest part of hatching is placing the hatch, not
<p>To insert external reference:</p>
defining it. Hatching an entire object is the simplest way to place a hatch.
<ol>
But often the area you want to hatch is fairly complex, and AutoCAD needs to do
<li>Type ''MVSETUP'' in the command window.</li>
some calculations to determine it. The Boundary Hatch dialog box offers two
<li>AutoCAD will prompt: ''Enable paper space [Y/N]''. Select ''Y''.</li>
ways to specify the hatch boundary— you can pick points inside an area and let
<li>AutoCAD will prompt: ''Enter Option''. Select ''Title Block''.</li>
AutoCAD try to find an enclosed boundary, or you can select objects. If you
<li>AutoCAD will prompt: ''Enter Title Block Option''. Select ''Insert''.</li>
want to hatch an entire object:</p>
<li>Figure 24 shown below will appear. Type ''7'' and press ''Enter'' to select '''ANSI A'''.


[[Image:image067.jpg|frame|center|Figure 24]]


<ol>
<li>AutoCAD will prompt: ''Create Drawing''. Select ''Yes''.
<li>Choose Select Objects. AutoCAD returns you temporarily to your drawing.</li>
<p>'''''Note''': AutoCAD will take you to a new window which shows how the paper will look when it prints. The screen in the middle is known as the viewport (The grid area in Figure 25) and you can move images in and out of this viewport to print desired images. This is very helpful when drawing multiple images in one AutoCAD file but wanting to print only a couple together, or separately. To access the viewport, double click in the center. You can now draw directly in this space or type “pan” and move the background around to find other drawings in the same file.''</p>


<li>Select all the objects you want to hatch. You can use all the standard object
<li>The title block acts as a single component. You can select a single line and the entire title block will be selected. You can now scale the title block, move it or make any other changes you wish. </li>
selection options to select objects. Remove and Add are especially helpful.</li>
<p>The drawing's scale is set to be 1"=10'. Since there are 12 inches in 1 foot and
 
the scale is set to be 1 inch per 10 feet. You would get 12 x 10 = 120, thus making
<li>Press Enter to end object selection and return to the dialog box.</li>
the Scale for X, Y and Z to be 120.</p>
</ol>
</ol>


<p>If the area you want to hatch does not neatly fit into one or more objects,
[[Image:image069.jpg|frame|center|Figure 25]]
choose <i>Pick Points</i>. At the <i>Select internal point</i>: prompt, pick a point
that is inside the boundary that you want to hatch. You can continue to pick internal
points to hatch adjoining areas. AutoCAD helpfully highlights the boundaries it finds.
Press Enter to return to the dialog box.</p>


<h2>AutoCAD Exercise</h2>
<h2>AutoCAD Exercise</h2>


<p>We will be drawing Josephine Poly’s room. It will have walls, a window, and a door.
<p>We will be drawing Josephine Poly's room. It will have walls, a window, and a door.
It will be dimensioned and have a title block.</p>
It will be dimensioned and have a title block.</p>


Line 626: Line 533:


<p>Your TA will show you how to use AutoCAD to create the elements you will need to
<p>Your TA will show you how to use AutoCAD to create the elements you will need to
complete this assignment. The scale for the drawing is 1�? = 10’.</p>
complete this assignment. The scale for the drawing is 1" = 10'.</p>


<p>First insert external reference, refer to page setup.  (See Figure 33)</p>
<p>First insert external reference, refer to page setup.  (See Figure 29)</p>


<p align=center>[[Image:image073.jpg]]</p>
[[Image:image073.jpg|frame|center|Figure 29]]
 
<p class=caption>Figure 33</p>


<p>Now it is time to start creating the drawing, so type the word line in the command
<p>Now it is time to start creating the drawing, so type the word line in the command
box. The cursor will then ask you to specify a point on the screen to start the line.
box. The cursor will then ask you to specify a point on the screen to start the line.
To specify a point on the screen, move the cursor to the point that you want to start
To specify a point on the screen, move the cursor to the point that you want to start
the line and click the left mouse clicker as shown in Figure 34.</p>
the line and click the left mouse clicker as shown in Figure 30.</p>


<p align=center>[[Image:image075.jpg]]</p>
[[Image:image075.jpg|frame|center|Figure 30]]
 
<p class=caption>Figure 34</p>


<p>After you have specified the point that you want the line to start now you must
<p>After you have specified the point that you want the line to start now you must
specify were you want it to finish. To specify the length of a line type the
specify where you want it to finish. To specify the length of a line type the
following: @ <u>length</u> &lt; <u>angle</u>. For example the base line of drawing is
following: <u>length</u>&lt;<u>angle</u>. For example the base line of drawing is
20’ and is a horizontal line, type @20’&lt;0. (See Figure 35)</p>
20' and is a horizontal line, type 20'&lt;0. (See Figure 30)</p>
 
<p align=center>[[Image:image077.jpg]]</p>
 
<p class=caption>Figure 35</p>


<p>The next line is a vertical line 25’ long. </p>
<p>If the line cannot be seen fully in the viewport, go the View tab then in the ''Navigate'' group, click on the arrow next to the third option which should be set by default to ''Extents''. Select ''Out'' and zoom out as many times as needed to see the full object.</p>


<p align=center>[[Image:image079.jpg]]</p>
<p>The next line is a vertical line 25' long.</p>


<p class=caption>Figure 36</p>
[[Image:image079.jpg|frame|center|Figure 31]]


<p>The next line is another horizontal line, to the left. When choosing the angle
<p>The next line is another horizontal line, to the left. When choosing the angle
remember the Angles are in polar form.  This means a line to left is 180 degrees.</p>
remember the Angles are in polar form.  This means a line to left is 180 degrees.</p>


<p align=center>[[Image:image081.jpg]]</p>
[[Image:image081.jpg|frame|center|Figure 32]]
 
<p class=caption>Figure 37</p>


<p>For this particular exercise, you can see that we will only be dealing with
<p>For this particular exercise, you can see that we will only be dealing with
<b><i>right-angles.</i></b> So in order to simplify matters turn your “ortho�? on
<b><i>right-angles.</i></b> So in order to simplify matters turn your "ortho" on
by clicking on the ortho button situated at the bottom of the screen. Now go ahead
by clicking on the ortho button situated at the bottom of the screen. Now go ahead
and finish drawing the outer-walls. At this point your drawing should look like the
and finish drawing the outer-walls. At this point your drawing should look like the
following as shown in Figure 357.</p>
following as shown in Figure 32.</p>


<p align=center>[[Image:image083.jpg]]</p>
<p>Note: When in ortho mode it is not necessary to specify the angle. Just point the line in the direction you wish to go and type in the length then press enter.</p>


<p class=caption>Figure 38</p>
[[Image:image083.jpg|frame|center|Figure 33]]


<p>Now we are going to draw the inner-walls. The distance between the inner and
<p>Now we are going to draw the inner-walls. The distance between the inner and
outer-walls is required to be 6 inches. To draw a line spaced exactly 6 inches and
outer-walls is required to be 6 inches. To draw a line spaced exactly 6 inches and
parallel from another one we will use the “offset�? command. Either click the
parallel from another one we will use the "offset" command. Either click the
“offset�? icon or type offset in the command window. Once you do, the command
"offset" icon or type offset in the command window. Once you do, the command
window will display the following <i>Specify
window will display the following <i>Specify
offset distance or [Through] &lt;Through&gt;</i>: prompting you to enter the
offset distance or [Through] &lt;Through&gt;</i>: prompting you to enter the
distance from the original line you wish to create the parallel line. Type the
distance from the original line you wish to create the parallel line. Type the
following exactly and press enter: 6�? Afterwards, the command window will
following exactly and press enter: 6" Afterwards, the command window will
display <i>Select object to offset or
display <i>Select object to offset or
&lt;exit&gt;</i>:  basically asking you
&lt;exit&gt;</i>:  basically asking you
Line 689: Line 586:
to offset</i>:  which means on which side
to offset</i>:  which means on which side
of the original line you want to create the new line parallel to it; i.e. the
of the original line you want to create the new line parallel to it; i.e. the
left or right of it. For our case let’s start on the right most
left or right of it. For our case let's start on the right most
line/outer-wall. The side to which you will “offset�? will be to the left of the
line/outer-wall. The side to which you will "offset" will be to the left of the
original line because you want to create the inner-walls. Your drawing should
original line because you want to create the inner-walls. Your drawing should
now look like the following Figure 39.</p>
now look like the following Figure 34.</p>
 
<p align=center>[[Image:image085.jpg]]</p>
 
<p class=caption>Figure 39</p>


<p>Now that you know how to “offset�?, go ahead and do that to all the outer-walls.
[[Image:image085.jpg|frame|center|Figure 34]]
When your are done with that you will notice that your drawing has all the
inner-walls intersecting one another and in contact with the outer-walls. </p>


<p align=center>[[Image:image087.jpg]]</p>
<p>Now that you know how to "offset", go ahead and offset all the outer-walls.
When you are done with that you will notice that your drawing has all the
inner-walls intersecting one another and in contact with the outer-walls.</p>


<p class=caption>Figure 40</p>
[[Image:image087.jpg|frame|center|Figure 35]]


<p>In order to correct this we will use the trim command. For the lines that are
<p>In order to correct this we will use the trim command. For the lines that are
intersecting one another we will trim them. Type “trim�? or click on the trim icon.
intersecting one another we will trim them. Type "trim" or click on the trim icon.
AutoCAD will display <i>Select cutting
AutoCAD will display <i>Select cutting
edges… Select objects:  </i> select the line you wish to use as the edge
edges… Select objects:  </i> select the line you wish to use as the edge
Line 716: Line 609:
of the line you wish to trim along your selected cutting edge. The portions we
of the line you wish to trim along your selected cutting edge. The portions we
wish to eliminate are the sections of the inner-walls that protrude beyond the
wish to eliminate are the sections of the inner-walls that protrude beyond the
6�? boundary and come in contact with the outer-wall. When you “trim�? all those
6" boundary and come in contact with the outer-wall. When you "trim" all those
sections your drawing should look like the following Figure 41.</p>
sections your drawing should look like the following Figure 36.</p>


<p align=center>[[Image:image089.jpg]]</p>
[[Image:image089.jpg|frame|center|Figure 36]]
 
<p class=caption>Figure 41</p>


<p>When you are done trimming you will
<p>When you are done trimming you will
notice that there is a section of the inner-wall that has a gap in it. In order
notice that there is a section of the inner-wall that has a gap in it. In order
to correct this problem we will use the extend command. Typed “extend�? in the command
to correct this problem we will use the extend command. Typed "extend" in the command
window or click the extend icon. You will receive the message <i>Current settings:
window or click the extend icon. You will receive the message <i>Current settings:
Projection=UCS, Edge=None Select boundary edges ... Select objects</i>:  
Projection=UCS, Edge=None Select boundary edges ... Select objects</i>:  
Line 732: Line 623:
message displayed will be <i>Select object
message displayed will be <i>Select object
to extend or shift-select to trim or [Project/Edge/Undo]:  </i> which is asking you to
to extend or shift-select to trim or [Project/Edge/Undo]:  </i> which is asking you to
select the object that you wish to extend, however, before you select that line, type “edge�?
select the object that you wish to extend, however, before you select that line, type "edge"
and press enter. AutoCAD will then display the following message <i>Enter an implied edge
and press enter. AutoCAD will then display the following message <i>Enter an implied edge
extension mode [Extend/No extend] &lt;No extend&gt;:  </i> and reply to this by typing “extend�?
extension mode [Extend/No extend] &lt;No extend&gt;:  </i> and reply to this by typing "extend"
and press enter. When you do this AutoCAD will again display the message <i>Select object to
and press enter. When you do this AutoCAD will again display the message <i>Select object to
extend or shift-select to trim or [Project/Edge/Undo]</i>:, now select the line
extend or shift-select to trim or [Project/Edge/Undo]</i>:, now select the line
you wished to extend. Your drawing should now look like the following Figure 42.</p>
you wished to extend. Your drawing should now look like the following Figure 37.</p>
 
<p align=center>[[Image:image091.jpg]]</p>


<p class=caption>Figure 42</p>
[[Image:image091.jpg|frame|center|Figure 37]]


<p>Now let’s add a window to Josephine’s room. We do this by drawing a 6 inch line
<p>Now let's add a window to Josephine's room. We do this by drawing a 6 inch line
from the inner-wall to the outer-wall along the right side of the room. Then we offset
from the inner-wall to the outer-wall along the right side of the room. Then we offset
that line by 2.5 feet in the appropriate direction. Now turn “osnap�?
that line by 2.5 feet in the appropriate direction. Now turn "osnap"
on and make sure that in its settings tab the midpoint option is selected. Once
on and make sure that in its settings tab the midpoint option is selected. Once
that is done, draw a line from the midpoint of one line to the next. Your
that is done, draw a line from the midpoint of one line to the next. Your
drawing should now look like the following Figure 43.</p>
drawing should now look like the following Figure 38.</p>
 
<p align=center>[[Image:image093.jpg]]</p>


<p class=caption>Figure 43</p>
[[Image:image093.jpg|frame|center|Figure 38]]


<p>Now let’s put a door. On the top-left section of the room draw a 6 inch line from
<p>Now let's put a door. On the top-left section of the room draw a 6 inch line from
the inner-wall to the outer-wall and offset this line through a distance of 4 feet. Once
the inner-wall to the outer-wall and offset this line through a distance of 4 feet. Once
you do that “trim�? the inner and outer-walls situated in-between these to lines. Your
you do that "trim" the inner and outer-walls situated in-between these two lines. Your
drawing should look like the following Figure 44.</p>
drawing should look like the following Figure 39.</p>


<p align=center>[[Image:image095.jpg]]</p>
[[Image:image095.jpg|frame|center|Figure 39]]
 
<p class=caption>Figure 44</p>


<p>Now draw a line 4 feet in length extending outward from the room from the upper
<p>Now draw a line 4 feet in length extending outward from the room from the upper
corner of the outer-wall section you just trimmed. Then draw an arc of radius 4 feet
corner of the outer-wall section you just trimmed. Then draw an arc of radius 4 feet
from the protruding line to the bottom corner of the outer-wall section you just trimmed.
from the protruding line to the bottom corner of the outer-wall section you just trimmed.
Your drawing should look like the following Figure 45.</p>
Your drawing should look like the following Figure 40.</p>
 
<p align=center>[[Image:image097.jpg]]</p>


<p class=caption>Figure 45</p>
[[Image:image097.jpg|frame|center|Figure 40]]


<p>At this point make sure that you
<p>At this point make sure that you
have three layers, two will have a predetermined name by AutoCAD (one for your
have three layers, two will have a predetermined name by AutoCAD (one for your
title block and another for command purposes) the second one should be named
title block and another for command purposes) the second one should be named
“Room�? for the actual room itself which is what you should have been using to
"Room" for the actual room itself which is what you should have been using to
draw your room in. Create a fourth layer called “Text�? and a fifth one named
draw your room in. Create a fourth layer called "Text" and a fifth one named
“Title block�?. You will use this layer to label the room as well as the
"Title block". You will use this layer to label the room as well as the
appropriate sections of your title block. Set the “text�? layer to current and
appropriate sections of your title block. Set the "text" layer to current and
click on the “Multiline Text�? icon and create a text
click on the "Multiline Text" icon and create a text
box inside the room. Type the following: Josephine Poly’s
box inside the room. Type the following: Josephine Poly's
Room. Then set the current layer to be “title block�?. In the top left box of
Room. Then set the current layer to be "title block". In the top left box of
the bottom section of the title block enter the company name of “Polytechnic
the bottom section of the title block enter the company name of "NYU Polytechnic School of Engineering", in the top right box of the bottom section type the names of your
University�?, in the top right box of the bottom section type the names of your
partner and yourself. In the box labeled "scale" input the scale of
partner and yourself. In the box labeled “scale�? input the scale of
your drawing which in our case should be " 1"=10' ". Now switch your current
your drawing which in our case should be “ 1�?=10’ �?. Now switch your current
layer to the "Text" layer and type, in the box below the one you inserted you
layer to the “Text�? layer and type, in the box below the one you inserted you
and your partners' names, "Josephine Poly's Room" and
and your partners’ names, “Josephine Poly’s Room�? and
in the box labeled "DWG. NO." type 1A. Your drawing should now look like the
in the box labeled “DWG. NO.�? type 1A. Your drawing should now look like the
one below in Figure 41:</p>
one below in Figure 46:</p>
 
<p align=center>[[Image:image099.jpg]]</p>


<p class=caption>Figure 46</p>
[[Image:image099.jpg|frame|center|Figure 41]]


<p>Now create a new layer called “Electrical�?
<p>Now create a new layer called "Electrical"
and make it current. Create a text box by the door entrance inside the room and
and make it current. Create a text box by the door entrance inside the room and
type the letter “S�? which represents a light switch. Rotate the text box 90 degrees such
type the letter "S" which represents a light switch. Rotate the text box 90 degrees such
that it is facing in the same plane that the respective wall exists in (y-axis).
that it is facing in the same plane that the respective wall exists in (y-axis).
Then in the same layer create the following two objects shown below.</p>
Then in the same layer create the following two objects shown below in Figure 42.</p>


<p align=center>[[Image:image101.jpg]] [[Image:image103.jpg]]</p>
<div><div style="float: left; display: inline;">[[Image:image101.jpg|frame|center|Figure 42a]]</div><div style="float: left; display: inline; width: 10%;">&nbsp;</div><div style="float: left; display: inline;">[[Image:image103.jpg|frame|center|Figure 42b]]</div></div><br clear="both" />
<p class=caption>Figure 47</p>


<p>These represent electrical outlets of 220V and 120V respectively. Make them an
<p>These represent electrical outlets of 220V and 120V respectively. Make them an
Line 810: Line 689:
are attached to the wall so if the wall is moved the outlets will come with it. To do this,
are attached to the wall so if the wall is moved the outlets will come with it. To do this,
you can use the rotation command, if necessary. Now turn the text layer
you can use the rotation command, if necessary. Now turn the text layer
off and type “Electrical�? where you had previously typed “Josephine Poly’s Room�? and in the
off and type "Electrical" where you had previously typed "Josephine Poly's Room" and in the
box labeled “DWG. NO.�? type 1B. Your drawing should now look similar to the one below in
box labeled "DWG. NO." type 1B. Your drawing should now look similar to the one below in
Figure 48.</p>
Figure 43.</p>


<p align=center>[[Image:image105.jpg]]</p>
[[Image:image105.jpg|frame|center|Figure 43]]


<p class=caption>Figure 48</p>
<p>Now create a new layer called "Dimension", set it to current, and turn the electrical
 
layer off. Type "Dimension" where you had previously typed "Electrical" and in the box
<p>Now create a new layer called “Dimension�?, set it to current, and turn the electrical
labeled "DWG. NO." type 1C. Create linear dimensions for all the outer-walls except for
layer off. Type “Dimension�? where you had previously typed “Electrical�? and in the box
labeled “DWG. NO.�? type 1C. Create linear dimensions for all the outer-walls except for
the one with the door. Then create one for the window and door. Your drawing should now
the one with the door. Then create one for the window and door. Your drawing should now
look similar to the one below in Figure 49.</p>
look similar to the one below in Figure 44.</p>
 
<p align=center>[[Image:image107.jpg]]</p>


<p class=caption>Figure 49</p>
[[Image:image107.jpg|frame|center|Figure 44]]


<p>Now you are done. Congratulations.</p>
<p>Now you are done. Congratulations.</p>
Line 832: Line 707:
<h3>Printing</h3>
<h3>Printing</h3>


<p>In order print the drawings, have the drawing set to as you
<p>In order to print the drawings, have the drawing set to as you
would like it printed. For example, if you would like the have the dimensions
would like it printed. For example, if you would like to only have the dimensions
printed only have the dimensions layer on and the others off.</p>
printed, have the dimensions layer on and the others off. Have all the layers turned on
before printing.</p>


<p>Go to File on the menu bar and select plot.  A plot dialog window will appear as
<p>Go to the top bar of AutoCAD.</p>
shown in Figure 50. Make sure the proper printer in selected in the Plot Device
[[Image:image114.jpg]]
tab. As for Figure 50, it is the Lab JAB 574.</p>


<p align=center>[[Image:image109.jpg]]</p>
<p>Click on the last icon that looks like a printer. This is the plot icon. A plot dialog window will appear as
shown in Figure 45. Make sure the proper printer is selected in the Plot Device
tab.</p>


<p class=caption>Figure 50</p>
[[Image:image109.jpg|frame|center|Figure 45]]


<p>Next, select the Plot Settings and change the Plot Scale to 1 inches = 120 drawing
<p>Next, select the Plot Settings and change the Plot Scale to custom and then specify underneath: 1 inches = 120 drawing
units. Check off Center the Plot in the Plot Offset section. And last but not least,
units. Check off Center the Plot in the Plot Offset section. And last but not least,
select Extents in the Plot Area. Everything should look like Figure 51. You may preview
select Extents in the Plot Area. Everything should look like Figure 46. You may preview
your drawing print out by click on Full Preview. When satisfied with the entire options
your drawing print out by click on Preview. When satisfied with the entire options
click OK.</p>
click OK.</p>


<p align=center>[[Image:image111.jpg]]</p>
[[Image:image111.jpg|frame|center|Figure 46]]
 
<p class=caption>Figure 51</p>
 
<h2>Introduction to Matlab</h2>
 
<h3>Starting Matlab:</h3>
 
<p>Open Matlab. </p>
 
<h3>Matlab Desktop:</h3>
 
<p align=center>[[Image:Engg_SW_II_image200.gif]]</p>
 
<p class=caption>Figure 52: Matlab Desktop</p>
 
<p><b>Command Window:</b>  The command window is the window you write commands
in to perform desired Matlab functions.</p>
 
<p><b>Current Directory:</b> The current directory window shows which directory
Matlab is currently using.  It can be replaced by the workspace window.</p>
 
<p><b>Workspace:</b> The workspace widow displays the names and the values of
the variable you are currently using in the Matlab workspace.</p>
 
<p><b>Command History:</b> The command history window displays the commands that
you have recently used in the Matlab command window.  This also displays
commands from previous Matlab sessions.</p>
 
<h3>Basic Arithmetic:</h3>
 
<ol>
<li>Open the workspace window, it should be empty</li>
 
<li>In the command window type 3 + 5 and press enter</li>
 
<li>Type a = 7 + 6;  in the command window, remember to include the semicolon
after the expression</li>
 
<li>Now type the letter “a�? in the command window and press enter</li>
 
<li>b = 16 – 4</li>
 
<li>c = 7 * 6</li>
 
<li>d = 25 / 5</li>
 
<li>e = 8 ^ 2</li>
 
<li>f = sqrt(36)</li>
 
<p><b>Note:</b> Matlab can perform multiple operations on series of
numbers, or matrices.  These tools are very useful in advanced mathematics such
as Linear Algebra.</p>
 
<li>A = [ 4 8 15 16 23 42 ] and B = [ 13 7 82 5 19 8 ]</li>
 
<li>C = A + B</li>
 
<li>D = B – A</li>
 
<li>E = A .* B</li>
 
<li>F = B ./ A</li>
 
<li>G = B .^ 2</li>
 
<li>H = sqrt(A)</li>
 
<p><b>Note:</b> The “:�? operator counts between two different
numbers. By default the value is “1�? though this can be changed.</p>
 
<li>I = 0:10</li>
 
<li>J = 0 : 0.5 : 5</li>
 
<li>K = 25 : 5 : 53</li>
 
<li>L = 100 : -3 : 80</li>
 
<li>M = [16 3 2 13; 5 10 11 8; 9 6 7 12; 4 15 14 1]</li>
 
<li>sum(M)</li>
</ol>
 
<h3>Basic Trigonometry:</h3>
 
<ol>
<li>In the command window type the word “clear�?</li>
 
<p><b>Note:</b> In Matlab <font face="Symbol">&#960;</font> is represented by the word “pi.�?</p>
 
<li>x = <font face="Symbol">&#960;</font>/2 and y = sin(x)</li>
 
<li>y = cos(<font face="Symbol">&#960;</font>)</li>
 
<li>x = <font face="Symbol">&#960;</font>/4 and y = sin(x)</li>
 
<li>y = cos(x)</li>
</ol>
 
<h3>2-D Plotting:</h3>
 
<ol>
<li>In the command window type the word “clear�?</li>
 
<li>x = 0 : <font face="Symbol">&#960;</font>/8 : 2<font face="Symbol">&#960;</font> and y = sin(x)</li>
 
<li>plot(x, y), save this plot as “EG sin�?</li>
 
<li>Now plot y = cos(x), save this plot as “EG cos�?</li>
 
<li>theta = 0 : <font face="Symbol">&#960;</font>/16 : 2<font face="Symbol">&#960;</font>;</li>
 
<li>x = cos(theta);  y = sin(theta);</li>
 
<li>Plot x against y and save this as “EG circle�?</li>
 
<p><b>Note:</b> exp(x) represents e<sup>x</sup></li>
 
<li>x = 0 : 5;  y = exp(x);</li>
 
<li>Again plot x against y and save this plot as “EG e�?</p>
</ol>
 
<h3>3-D Plotting:</h3>
 
<ol>
<li>In the command window type the word “clear�?</li>
 
<li>sphere(20) save this as “EG sphere�?</li>
 
<p align=center>[[Image:Engg_SW_II_image201.gif]]</p>
 
<p class=caption>Figure 2: Top of figure window</p>
 
<li>Click onto the rotation tool on the top of the window</li>
 
<li>Click on the figure and drag the mouse around the screen</li>
 
<li>z is equal to the space between zero and two with increments of 0.1 and 
r = sin(3<font face="Symbol">&#960;</font>z) + 2;</li>
 
<li>cylinder(r) save this as “EG cylinder�?</li>
 
<li>u = -5 : 0.2 : 5; [x, y] = meshgrid(u,u);</li>
 
<li>&nbsp;</li>
<p>[[Image:Engg_SW_II_image202.gif]]</p>
 
<li>surf(x,y,z)  save this as “EG surface�?</li>
 
 
<li>Copy and paste your Matlab code into a Word Document.  Copy your Matlab graphs
and paste them into the same Word Document underneath the code you used to make
them.</li>
 
<li>Exit Matlab by clicking on the red “x�? on the upper right hand corner of
the window</li>
 
<li>Submit this Word document to eg.poly.edu.</li>
</ol>


<p>You have now completed the lab. Log off the PC and make sure your work area is
<p>You have now completed the lab. Log off the PC and make sure your work area is

Latest revision as of 08:28, 2 September 2015

Objective

In this exercise, you will be introduced to additional software used by technical professionals. You will learn basic technical design methods using Computer-Aided Design (CAD) software, specifically AutoCAD. Later on in the course, you will use this knowledge to create designs, particularly in your semester-long design project.

Overview

In any design process, engineers must put their ideas on paper, usually in the form of a sketch. This initial drawing is done in pencil without rulers or straight edges. It shows some detail, for example, blocks represent objects and double parallel lines represent walls. The type of line used to draw an object is important because it indicates what is to be built. Here is a list of some types of lines and their uses:

Construction Line: Image001.jpg

The construction line is the one used most frequently in technical drawings. It indicates solid objects like walls.

Hidden Line: Image002.jpg

The hidden line is used to show hidden objects like wiring in walls.

Dimension Line: Image003.jpg

This line is used to indicate dimensions.

Center Line: Image004.jpg

This line is used to show the center of circles and curves on a drawing. Contractors are able to locate the center of the circle when this type of line is used.

These line types are used together to create a picture of the design. This picture can be isometric or orthographic. An isometric drawing is a three dimensional view. See Figure 1.

Image005.jpg

An orthographic drawing is a two dimensional view from different perspectives. There are usually three views - top, front and side. See Figure 2.

Image006.jpg

Computer-Aided Design

Computer-Aided Design (CAD) programs allow engineers to make precise scaled drawings in less time than more traditional methods. CAD drawing allows designers to make changes easily and efficiently making them more productive. You will need to understand the fundamentals of Computer-Aided Design to progress in your career.

This exercise has been designed to introduce the basics of CAD drawing.

Starting and Setting Up AutoCAD

Start AutoCAD 2010. (Note: It is best to have a 3 button mouse.)

Note: Beginning with AutoCAD 2010, Autodesk has changed the toolbar interface to resemble that of Microsoft Office's ribbon interface.

Once the program has loaded, you can close the Welcome Screen. Note that the tutorials on the left hand side are very useful and should be reviewed later on.

Figure 3

In the command box (bottom of the screen) type startup and the message startup(0) will appear. Type1 then press enter. Now go to the top of the page next to where it says 2D Drafting and Annotations will be the icon for a new blank project. Press this button and a Create New Drawing window will appear. Select the last option at the top of this window which will be Use a Wizard (see Figure 4).

Figure 4

Select Advanced Setup and the following window shown in Figure 5 will appear

Figure 5

For the length unit, select the type to be Engineering and choose the precision to be two decimal places. Then click next (See Figure 5).

The wizard will then take you through the setup for Angles, Angle Measurement, Angle Direction, and Area The defaults that appear can be left as is unless working on a special project. For the skill builder below, the default settings are correct.

Setting Up the Dimensions and the Text Style

Later on, we will be inputting text and dimensions into our drawing. However, it is best to set up a general style for the drawing due to the fact that the default settings are not sufficient for our needs.

First, select the Annotate tab on the ribbon. Click the arrow at the lower right-hand corner of the Dimensions group to access the Dimension Style Manager dialog window. (See Figure 6)

Figure 6

In the Dimension Style Manager window, select Modify.... (See Figure 7)

Figure 7

Under the Lines tab, change the following:

  • Offset from origin: 1'

Under the Symbols and Arrow tab, change the following:

  • Arrow Size: 1'

Under the Text tab, change the following:

  • Text Height: 1'

Under the Primary Units tab, change the following:

  • Unit Format: Engineering
  • Precision: 0'-0.00"

To change the text style, click the arrow at the lower right-hand corner of the Text group of the Annotate tab on the ribbon. (See Figure 8)

Figure 8

You may choose the type of font and change the height to 1' as shown below in Figure 9.

Figure 9

Command Window

At the bottom of the screen, you see a separate window showing a few lines of text. (You can change it to show as many lines as you like by dragging the top edge of the window up or down.) Notice the word Command. This is the command line. All commands can be executed by typing them on the command line. Even if you use a menu item or toolbar button to execute a command, you may need to look at the command line to see how AutoCAD responds. Often, AutoCAD provides options that must be typed in from the keyboard. Also, text that you type appears on the command line. For example, when you type in coordinates specifying a point, they appear on the command line. To see more of the command line, press F2 to open the AutoCAD Text window. You can scroll back through previous commands. Press F2 again to close the window. (See Figure 10)

Figure 10

AutoCAD Tools

Draw Tools

To Draw a Line

  1. Type line or l in the command window, then Enter, or click the Line icon [ Image023.jpg ] in the Draw group under the Home tab.
  2. Click the point where you want the line to begin. Drag the line in the direction you want it to go, and specify its length when prompted. Hit Enter.
  3. Press Escape to exit the line command.

Note: Most of the commands can be done by clicking an icon or typing into the command window.

Drawing Lines with Specific Angles and Lengths

Relative polar coordinates take the form distance<angle.

By default, angles are measured according to Figure 11.

Figure 11

In order to draw a line that is 10' at a 30º angle:

  1. Click on the Line icon [ Image023.jpg ].
  2. Click the point where you want the line to begin.
  3. Then type in the Command Window: distance<angle. Hit Enter.

    EX: 10'<30, then hit Enter

  4. Press Escape to exit the Line command.

Drawing Arcs

To draw an arc, choose Arc [ Image043.jpg ] from the Draw toolbar and follow the prompts. As with circles, object snaps are often helpful when drawing arcs.

When drawing an arc by using the Start, End, and Radius options, the three specifications actually define two possible arcs, one minor and one major. AutoCAD draws the minor arc by default, in the counterclockwise direction. (A minor arc is less than half a circle.) If you enter a negative number for the radius, AutoCAD draws the major arc (which is more than half a circle). The options requiring an angle also define two possible arcs, one drawn counterclockwise and one drawn clockwise.

AutoCAD draws the counterclockwise arc by default. If you type a negative number for the angle, AutoCAD draws the arc clockwise.

Drawing Dimensions

Just as the most common objects are lines, the most common dimensions are linear dimensions.

Use linear dimensions for lines, a straight segment of a polyline, or a straight segment in a block. You can also use a linear dimension for arcs and circles—you get the linear length of the arc (not its perimeter length) and the diameter of the circle.

When dimensioning a drawing, create a new layer and label the dimensions so that you can toggle the layer on and off. That way, when you modify your drawing, there will be less clutter on the screen.

To dimension a line, choose Dimension from the menu bar and select linear. AutoCAD responds with the Specify first extension line origin or <select object>: prompt. You can now either pick two extension line origin points or press Enter (or right-click) and select an object for dimensioning. (See Figure 23)

Figure 23

Modify Tools

Offsetting Objects

The Offset command creates lines or curves parallel to one existing object. The beauty of this command is apparent when you start to create complex objects, such as polylines. Polygons and rectangles are polylines, meaning that they are treated as one object. Using OFFSET, you can create concentric polygons, for example the figure below shows three concentric polygons. The red polygon was created with the POLYGON [ Image036.jpg ] command, which is found under the Home tab by clicking the arrow at the bottom right corner of the Draw group and selecting the polygon button shown above. The blue polygon was subsequently created by using OFFSET as shown in Figure 18.

Example:

Figure 18a
 
Figure 18b


To offset a line or an object:

  1. Click Image041.jpg, found under the Home tab in the Modify group, and then on the command window specify offset distance and then press Enter.
  2. Select the object and click in the direction you would like the object to be offset.

Mirroring Objects

Many drawings have symmetrical elements. Often, especially in mechanical drawing, you can create one-half or one-quarter of a model and complete it simply by mirroring what you have drawn.

To mirror, select an object or objects and then choose Mirror [ Image045.jpg ] from the Modify toolbar. Alternatively, choose Mirror from the Modify toolbar and then select an object or objects.

AutoCAD prompts for the first and second points of the mirror line. This is an imaginary line across which AutoCAD creates the mirrored object. The length of the line is irrelevant — only its start point and direction are important.

Note: Most mirror lines are orthogonal. Therefore, after you specify the first mirror point, turn on ORTHO and move the mouse in the direction of the second point. You can then quickly pick the second point. Polar tracking can also easily guide you to specify an orthogonal mirror line.

Example based on a mounting plate shown in Figure 19

  1. Choose Mirror from the Modify toolbar. Select objects: prompt appears at the command window. Pick the exterior line and two arcs and press Enter.
  2. At the Specify first point of mirror line: prompt, pick the intersection Image047.jpg in Figure 19. At the Specify second point of mirror line: prompt, pick the intersectionImage049.jpg.
  3. AutoCAD prompts: Delete source objects? [Yes/No] <N>: Press Enter to accept the default, No.
  4. Again choose Mirror from the Modify toolbar. At the Select objects: prompt, type P and then press Enter to pick the original lines. Then pick the new exterior line and two arcs and then press Enter.
  5. Figure 19
  6. At the Specify first point of mirror line: prompt, pick the intersection Image053.jpg. At the Specify second point of mirror line: prompt, pick the intersectionImage055.jpg. Press Enter again at the Delete source objects? [Yes/No] <N>: prompt.
  7. AutoCAD completes the mounting plate seen in Figure 20.
Figure 20

Trimming objects

As you edit a drawing, you may find that lines or arcs that once perfectly met other objects now hang over. To trim an object, you must first specify the cutting edge, which defines the point at which AutoCAD cuts the object you want to trim. You define the cutting edge by selecting an object. You can select several cutting edges and several objects to trim at one time, as shown in Figure 21. When you select an object to trim, you must pick the object on the side that you want trimmed (not on the side that you want to remain). A common use for the TRIM command is to create intersections of walls in architectural floor plans.

While using the TRIM command, you can switch to extending objects by pressing the Shift key as you select objects to trim.

Figure 21

To trim an object, choose Trim [ Image060.jpg ] from the Modify toolbar. You cannot select objects before starting the TRIM command. AutoCAD displays the Current settings: Projection=UCS, Edge=None, Select cutting edges ... Select objects: prompt. AutoCAD lets you know the values of the two system variables that affect trimming. The Projection setting is used only for 3D models. The Edge setting is used for implied intersections. When Edge is set to Extend, AutoCAD trims to the implied intersection of the cutting edge and the object to be trimmed. At this prompt, pick the object(s) that you want to use as a cutting edge. Press Enter to end object selection. (See Figure 21)

Now you may be able to cut the lines within the cutting edges. Use the Undo (CTRL+Z) option, or type u then press Enter, if the results of the trim are not what you want. You can then continue to select objects to trim.

Rotating an Object

To rotate an object, choose Rotate [ Image044.jpg ] from the Modify toolbar and select an object. Alternatively, select an object and then choose Rotate from the Modify toolbar. At the Specify base point: prompt from the command window, indicate the point around which you want to rotate. At the Specify rotation angle or [Reference]: prompt, type an angle at the command line.

The Reference option lets you specify an absolute existing rotation angle and the desired angle. At the Specify the reference angle <0>: prompt, you type in an angle or specify an angle by picking two points. These can be object snap points on the object that specify the object's current angle. At the Specify the new angle: prompt, type or pick a new angle. You can also pick an object snap on another object in the drawing to indicate this new angle. You can use the Reference option to align the object with the X or Y axis or with another object in your drawing.

Hatching

To hatch an area, select Draw from the menu bar and select Hatch icon [ Image112.jpg ] in the Draw group under the Home tab. AutoCAD opens a new tab, Hatch Creation, as shown below in Figure 26.

Figure 26

Click on the arrow at the bottom right corner of the Options to open the Hatch and Gradient window.

Figure 27

Use this dialog box to define your hatch. From the Type and Pattern drop-down box, choose one of the three options:

  1. Predefined: Enables you to select one of AutoCAD's hatch patterns.
  2. User-defined: Enables you to define your own hatch pattern by specifying the angle and spacing, using the current linetype.
  3. Custom: Enables you to choose a pattern you have created in your own .pat file.

Click the Pattern drop-down box to choose the hatch patterns from a list. (See Figure 28)

Figure 28

In the palette, click the tabs to see the different types of hatches. Click the image tile to choose a hatch pattern and click OK.

Determining Hatching Boundaries

The hardest part of hatching is placing the hatch, not defining it. Hatching an entire object is the simplest way to place a hatch. But often the area you want to hatch is fairly complex, and AutoCAD needs to do some calculations to determine it. The Boundary Hatch dialog box offers two ways to specify the hatch boundary— you can pick points inside an area and let AutoCAD try to find an enclosed boundary, or you can select objects. If you want to hatch an entire object:


  1. Choose Select Objects. AutoCAD returns you temporarily to your drawing.
  2. Select all the objects you want to hatch. You can use all the standard object selection options to select objects. Remove and Add are especially helpful.
  3. Press Enter to end object selection and return to the dialog box.

If the area you want to hatch does not neatly fit into one or more objects, choose Pick Points. At the Select internal point: prompt, pick a point that is inside the boundary that you want to hatch. You can continue to pick internal points to hatch adjoining areas. AutoCAD helpfully highlights the boundaries it finds. Press Enter to return to the dialog box.

File Tools

Layers

The best way to organize your drawing into colors, linetypes, and lineweights is to use layers. Layers offer powerful features that enable you to distinguish all the various elements of your drawing. In an architectural drawing, for example, common layers are walls, doors, windows, plumbing, electrical, fixtures, structural elements, notes (text), dimensions, ceiling, insulation, posts, title block, and so on. Mechanical drawings might use center, hidden, hatch, object, and title block layers. Each discipline has its own conventions, and you might have specific conventions where you work.

Besides having a color, linetype, and lineweight, every layer must have a name. All drawings come with a default layer, called layer 0 (zero). Its color is Black/white, its linetype is Continuous, and its lineweight is Default. (The lineweight for Default is 0.010 inch or 0.25 mm.) All the exercises in this book up to this point have used layer 0. To create a new layer, you must give it a name, a color, a linetype, and a lineweight. You can then start drawing on that layer.

Layers also have four states. These states control visibility, regeneration, editability, and plottability of layers:

  • On/Off: On layers (the default) are visible. Off layers are invisible and are regenerated with the drawing.
  • Thawed/Frozen: Thawed layers (the default) are visible. Frozen layers are invisible and are not regenerated with the drawing. However, when you thaw a frozen layer, it requires regeneration. If you have floating viewports, you can also freeze a layer just in the current viewport, or only for new viewports that you create.
  • Unlocked/Locked: Unlocked layers (the default) are visible and editable. Locked layers are visible but cannot be edited.
  • Plottable/Not Plottable: Plottable layers are plotted. Not plottable layers are not plotted. This setting affects only layers that are on or thawed because off and frozen layers are not plotted anyway.

Creating a new layer:

To create a new layer, select the Layer Properties Manager [ Image061.jpg ] from the Layers group under the Home tab.

AutoCAD opens the Layer Properties Manager, as shown in Figure 22.

Figure 22

This dialog box lists all current layers and their properties. You can also create new layers and modify current ones.

Below the Command Window

Image025.jpg

From left to right: Infer Constraints, Snap Mode, Grid, Ortho Mode, Polar Tracking, Object Snap, 3D Object Snap, Object Snap Tracking UCS, Allow/Disallow Dynamic, Dynamic Input, Show/Hide Lineweight, Show/Hide Transparency, Quick Properties, Select Cycling.

  1. When in orthogonal mode—ortho mode as it's called for short—you can only draw orthogonal (right angles) lines with the mouse. Ortho mode also affects editing. For example, with ortho mode on, you can only move objects vertically or horizontally. Combined with snap and grid, ortho mode makes drawing easier and more efficient. Ortho mode is also great for direct distance entry. Click ORTHO on the status bar to toggle ortho mode on and off. You cannot have polar tracking on at the same time that ortho mode is on.
  2. Object snap (osnap) allows a user to precisely acquire certain points on a line or object to be able to manipulate the drawing, such as aligning or attaching those points that are selected to other points.
  3. Example:

    Figure 12

    In order to draw a line from endpoint A to endpoint B in Figure 12 accurately and ensure that we are actually attaching the ends of the lines and not the space before, near, or around it, we utilize a command called "osnap".

    To toggle osnap on and off, click the "OSNAP" button. Figure 13 shows the use of osnap.

    Figure 13

    Step 1: Click on the line icon [ Image023.jpg ] and when you situate the crosshair at the endpoint of line A and you will notice a pink or green box appear. This means that the endpoint has acquired by AutoCAD.

    Step 2: Once the endpoint of line A has been acquired, click and move the crosshair to the end of line B. You will notice that the endpoint of line B has been found by AutoCAD.

    Step 3: Click and press enter to complete the line command function.

    Note: To click on different points of a line, you will need to change the osnap settings. In order to go to the settings of osnap, you will have to right click on any part below the command window and a context menu will appear. See Figure 14.

    Figure 14

    Select settings and then you can choose the settings for which option you would like to change. (See Figure 15)

    Figure 15
  4. LWT is the Lineweight function, and it controls the width of the line. A lineweight can help to distinguish various elements of your drawing, both on-screen and on paper. For example, you could use a thicker lineweight to indicate planned construction changes, for dimension lines, or even to represent the true width of an object. The LWT button on the status bar turns on and off the display of lineweights. By default, LWT is off. (See Figure 16)
Figure 16

In order to select the line width of a line, first select the line(s) and then click on the Line Weight Control and select the desired thickness as show in Figure 17.

Figure 17

Inserting an External reference [Title Block]

External references (commonly called xrefs) enable you to view any drawing as a reference while in your current drawing. The external drawing is not part of your current drawing. The current drawing keeps track of the location and name of an external reference so you can always reference it easily. As with blocks, you can snap to objects in the external reference, thereby using it as a reference for the drawing process. You can also change the visibility settings of the xref's layers.

To insert external reference:

  1. Type MVSETUP in the command window.
  2. AutoCAD will prompt: Enable paper space [Y/N]. Select Y.
  3. AutoCAD will prompt: Enter Option. Select Title Block.
  4. AutoCAD will prompt: Enter Title Block Option. Select Insert.
  5. Figure 24 shown below will appear. Type 7 and press Enter to select ANSI A.
    Figure 24
  6. AutoCAD will prompt: Create Drawing. Select Yes.

    Note: AutoCAD will take you to a new window which shows how the paper will look when it prints. The screen in the middle is known as the viewport (The grid area in Figure 25) and you can move images in and out of this viewport to print desired images. This is very helpful when drawing multiple images in one AutoCAD file but wanting to print only a couple together, or separately. To access the viewport, double click in the center. You can now draw directly in this space or type “pan” and move the background around to find other drawings in the same file.

  7. The title block acts as a single component. You can select a single line and the entire title block will be selected. You can now scale the title block, move it or make any other changes you wish.
  8. The drawing's scale is set to be 1"=10'. Since there are 12 inches in 1 foot and the scale is set to be 1 inch per 10 feet. You would get 12 x 10 = 120, thus making the Scale for X, Y and Z to be 120.

Figure 25

AutoCAD Exercise

We will be drawing Josephine Poly's room. It will have walls, a window, and a door. It will be dimensioned and have a title block.

Image032.jpg

Your TA will show you how to use AutoCAD to create the elements you will need to complete this assignment. The scale for the drawing is 1" = 10'.

First insert external reference, refer to page setup. (See Figure 29)

Figure 29

Now it is time to start creating the drawing, so type the word line in the command box. The cursor will then ask you to specify a point on the screen to start the line. To specify a point on the screen, move the cursor to the point that you want to start the line and click the left mouse clicker as shown in Figure 30.

Figure 30

After you have specified the point that you want the line to start now you must specify where you want it to finish. To specify the length of a line type the following: length<angle. For example the base line of drawing is 20' and is a horizontal line, type 20'<0. (See Figure 30)

If the line cannot be seen fully in the viewport, go the View tab then in the Navigate group, click on the arrow next to the third option which should be set by default to Extents. Select Out and zoom out as many times as needed to see the full object.

The next line is a vertical line 25' long.

Figure 31

The next line is another horizontal line, to the left. When choosing the angle remember the Angles are in polar form. This means a line to left is 180 degrees.

Figure 32

For this particular exercise, you can see that we will only be dealing with right-angles. So in order to simplify matters turn your "ortho" on by clicking on the ortho button situated at the bottom of the screen. Now go ahead and finish drawing the outer-walls. At this point your drawing should look like the following as shown in Figure 32.

Note: When in ortho mode it is not necessary to specify the angle. Just point the line in the direction you wish to go and type in the length then press enter.

Figure 33

Now we are going to draw the inner-walls. The distance between the inner and outer-walls is required to be 6 inches. To draw a line spaced exactly 6 inches and parallel from another one we will use the "offset" command. Either click the "offset" icon or type offset in the command window. Once you do, the command window will display the following Specify offset distance or [Through] <Through>: prompting you to enter the distance from the original line you wish to create the parallel line. Type the following exactly and press enter: 6" Afterwards, the command window will display Select object to offset or <exit>: basically asking you to select the original line you wish to offset from. Once you select the line you want, AutoCAD will ask you to Specify point on side to offset: which means on which side of the original line you want to create the new line parallel to it; i.e. the left or right of it. For our case let's start on the right most line/outer-wall. The side to which you will "offset" will be to the left of the original line because you want to create the inner-walls. Your drawing should now look like the following Figure 34.

Figure 34

Now that you know how to "offset", go ahead and offset all the outer-walls. When you are done with that you will notice that your drawing has all the inner-walls intersecting one another and in contact with the outer-walls.

Figure 35

In order to correct this we will use the trim command. For the lines that are intersecting one another we will trim them. Type "trim" or click on the trim icon. AutoCAD will display Select cutting edges… Select objects: select the line you wish to use as the edge along which you will cut another line. Press enter when you select the line you wish to use as your cutting edge. Once you do the command window will display the following Select object to trim or shift-select to extend or [Project/Edge/Undo]: basically asking you to select the portion of the line you wish to trim along your selected cutting edge. The portions we wish to eliminate are the sections of the inner-walls that protrude beyond the 6" boundary and come in contact with the outer-wall. When you "trim" all those sections your drawing should look like the following Figure 36.

Figure 36

When you are done trimming you will notice that there is a section of the inner-wall that has a gap in it. In order to correct this problem we will use the extend command. Typed "extend" in the command window or click the extend icon. You will receive the message Current settings: Projection=UCS, Edge=None Select boundary edges ... Select objects: which is asking you to select the line to which you wish to extend another one to. So select one of the lines in the gap area and press enter. The message displayed will be Select object to extend or shift-select to trim or [Project/Edge/Undo]: which is asking you to select the object that you wish to extend, however, before you select that line, type "edge" and press enter. AutoCAD will then display the following message Enter an implied edge extension mode [Extend/No extend] <No extend>: and reply to this by typing "extend" and press enter. When you do this AutoCAD will again display the message Select object to extend or shift-select to trim or [Project/Edge/Undo]:, now select the line you wished to extend. Your drawing should now look like the following Figure 37.

Figure 37

Now let's add a window to Josephine's room. We do this by drawing a 6 inch line from the inner-wall to the outer-wall along the right side of the room. Then we offset that line by 2.5 feet in the appropriate direction. Now turn "osnap" on and make sure that in its settings tab the midpoint option is selected. Once that is done, draw a line from the midpoint of one line to the next. Your drawing should now look like the following Figure 38.

Figure 38

Now let's put a door. On the top-left section of the room draw a 6 inch line from the inner-wall to the outer-wall and offset this line through a distance of 4 feet. Once you do that "trim" the inner and outer-walls situated in-between these two lines. Your drawing should look like the following Figure 39.

Figure 39

Now draw a line 4 feet in length extending outward from the room from the upper corner of the outer-wall section you just trimmed. Then draw an arc of radius 4 feet from the protruding line to the bottom corner of the outer-wall section you just trimmed. Your drawing should look like the following Figure 40.

Figure 40

At this point make sure that you have three layers, two will have a predetermined name by AutoCAD (one for your title block and another for command purposes) the second one should be named "Room" for the actual room itself which is what you should have been using to draw your room in. Create a fourth layer called "Text" and a fifth one named "Title block". You will use this layer to label the room as well as the appropriate sections of your title block. Set the "text" layer to current and click on the "Multiline Text" icon and create a text box inside the room. Type the following: Josephine Poly's Room. Then set the current layer to be "title block". In the top left box of the bottom section of the title block enter the company name of "NYU Polytechnic School of Engineering", in the top right box of the bottom section type the names of your partner and yourself. In the box labeled "scale" input the scale of your drawing which in our case should be " 1"=10' ". Now switch your current layer to the "Text" layer and type, in the box below the one you inserted you and your partners' names, "Josephine Poly's Room" and in the box labeled "DWG. NO." type 1A. Your drawing should now look like the one below in Figure 41:

Figure 41

Now create a new layer called "Electrical" and make it current. Create a text box by the door entrance inside the room and type the letter "S" which represents a light switch. Rotate the text box 90 degrees such that it is facing in the same plane that the respective wall exists in (y-axis). Then in the same layer create the following two objects shown below in Figure 42.

Figure 42a
 
Figure 42b


These represent electrical outlets of 220V and 120V respectively. Make them an appropriate size and place one 220V outlet along the bottom wall towards the left side and one 120V outlet towards the right side. Then make a copy of the 120V outlet paste it along the rightmost wall near the top. Make sure that the legs of the above objects are attached to the wall so if the wall is moved the outlets will come with it. To do this, you can use the rotation command, if necessary. Now turn the text layer off and type "Electrical" where you had previously typed "Josephine Poly's Room" and in the box labeled "DWG. NO." type 1B. Your drawing should now look similar to the one below in Figure 43.

Figure 43

Now create a new layer called "Dimension", set it to current, and turn the electrical layer off. Type "Dimension" where you had previously typed "Electrical" and in the box labeled "DWG. NO." type 1C. Create linear dimensions for all the outer-walls except for the one with the door. Then create one for the window and door. Your drawing should now look similar to the one below in Figure 44.

Figure 44

Now you are done. Congratulations.

Printing

In order to print the drawings, have the drawing set to as you would like it printed. For example, if you would like to only have the dimensions printed, have the dimensions layer on and the others off. Have all the layers turned on before printing.

Go to the top bar of AutoCAD.

Image114.jpg

Click on the last icon that looks like a printer. This is the plot icon. A plot dialog window will appear as shown in Figure 45. Make sure the proper printer is selected in the Plot Device tab.

Figure 45

Next, select the Plot Settings and change the Plot Scale to custom and then specify underneath: 1 inches = 120 drawing units. Check off Center the Plot in the Plot Offset section. And last but not least, select Extents in the Plot Area. Everything should look like Figure 46. You may preview your drawing print out by click on Preview. When satisfied with the entire options click OK.

Figure 46

You have now completed the lab. Log off the PC and make sure your work area is clean, with any scrap paper you used, etc. properly of.

Return to Table of Contents